Com Unit for MODBUS TCP FB8211H0756.3

Interface between the I/O modules and the PCS/PLC
Com unit for 80 analog or 184 digital channels
Communication via MODBUS TCP
Installation in suitable enclosures in Zone 1
Module can be exchanged under voltage (hot swap)
HART communication via MODBUS TCP
Configuration via FDT 1.2 DTM
Non-volatile memory for configuration and parameter settings
Self configuration in redundant systems
Permanently self-monitoring
Outputs drive to safe state in case of failures

Technical Data
Details
Informative Literature
Product Documentation
Design / Simulation
Approvals
Software
Associated Products
Ask an Expert

Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.

Download the complete datasheet as a PDF:

Datasheet excerpt: Technical data of FB8211H0756.3

Product Description
Com Unit for MODBUS TCP

Slots
Occupied slots		2
Supply
Connection		backplane bus
Rated voltage		5 V DC , only in connection with the power supplies FB92**
Power dissipation		2 W
Power consumption		2.5 W
Fieldbus connection
Fieldbus type		MODBUS TCP
Ethernet Interface
Connection type		wired to Ex e terminals via backplane
Transfer rate		10 MBit/s
Station connection		directly to PCS or PLC or via hubs or switches
Bus length		max. 100 m (Ethernet standard)
Addressing		IP address assigned via Ethernet
Ethernet address		IP V4 address (factory standard setting: 0.0.0.0, auto IP, DHCP)
Number of channels per station		max. 80 analog, max. 184 digital
Supported I/O modules		all FB remote I/O modules
HART communication		via Ethernet
Internal bus
Connection		backplane bus
Redundancy		via left front connector
Service interface
Connection		via right front connector in connection with service adapter SERV8001
Indicators/settings
LED indication		LED green (power supply): On = operating, fast flash = cold start LED red (collective alarm): On = internal fault, flashing = no Modbus TCP connection LED yellow (operating mode): flashing 1 (1:1 ratio) = active, normal operation; flashing 2 (7:1 ratio) = active, simulation
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2013
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Fieldbus standard		IEEE 802.3
Environmental test		EN 60068-2-14
Shock resistance		EN 60068-2-27
Vibration resistance		EN 60068-2-6
Damaging gas		EN 60068-2-42
Relative humidity		EN 60068-2-78
Ambient conditions
Ambient temperature		-40 ... 60 °C (-40 ... 140 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Relative humidity		95 % non-condensing
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz; transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g; 10 cycles frequency range 5 ... 100 Hz; transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g; 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 (module) , a separate housing is required acc. to the system description
Connection		via backplane
Mass		approx. 750 g
Dimensions		57 x 107 x 132 mm (2.2 x 4.2 x 5.2 inch)
Data for application in connection with hazardous areas
EU-type examination certificate		Presafe 19 ATEX 14058U
	Marking	Ex db eb q [ib] IIC Gb
Directive conformity
	Directive 2014/34/EU	EN IEC 60079-0:2018+AC:2020 EN 60079-1:2014 EN 60079-5:2015 EN 60079-7:2015+A1:2018 EN 60079-11:2012
International approvals
ATEX approval		Presafe 19 ATEX 14058U
IECEx approval		IECEx PRE 19.0013U
	Approved for	Ex db eb q [ib] IIC Gb
General information
System information		The module has to be mounted in appropriate backplanes (FB92**) in Zone 1, 2, or outside hazardous areas. Observe the corresponding EC-type examination certificate.
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.

Classifications

System	Classcode
ECLASS 13.0	27210121
ECLASS 12.0	27210121
ECLASS 11.0	27210121
ECLASS 10.0.1	27210121
ECLASS 9.0	27210121
ECLASS 8.0	27210121
ECLASS 5.1	27210121
ETIM 9.0	EC001485
ETIM 8.0	EC001485
ETIM 7.0	EC001485
ETIM 6.0	EC001485
ETIM 5.0	EC001485
UNSPSC 12.1	39121008

Details: FB8211H0756.3

Function

The MODBUS TCP com unit forms the interface between the I/O modules on the backplane and the process control system.

It supports all single width and dual width I/O modules. Thereby signals from NAMUR sensors, mechanical contacts, high-power solenoid drivers, power relays, sounders, and alarm LEDs are transported to the higher-level bus system.

The com unit can be easily configured via DTM and supports redundancy as well as HART.

Informative Literature: FB8211H0756.3

Literature	Language	File Type	File Size
Application Report - Communication Redundancy for Uninterrupted Operation	ENG	PDF	529 KB
Application Report - LB and FB Remote I/O Systems for Digitally Connecting Analog Field Devices	ENG	PDF	208 KB
Application Report - Space Saving Extension for Existing Plants	ENG	PDF	300 KB
Application Report - Using Remote I/O Systems for the Efficient Digitalization of Plants	ENG	PDF	371 KB

Product Documentation: FB8211H0756.3

System Descriptions	Language	File Type	File Size
Supported I/O modules	ENG	PDF	31 KB
Brief Instructions
Brief Instructions - Firmware update	ENG	PDF	5602 KB
Safety and Security Documentation
Instruction manual	ENG	PDF	183 KB
Manuals
Manual for LB8107/FB8207, LB8111/FB8211 com unit for MODBUS RTU/TCP	ENG	PDF	6849 KB
Hardware Manual FB-Remote-I/O-System	ENG	PDF	9157 KB
Software Information
Software Product Note Remote I/O DTM / Softwareproduktschein Remote I/O DTM	ALL	PDF	256 KB

Design / Simulation: FB8211H0756.3

CAD	Language	File Type	File Size
CAD 3-D / CAD 3-D	ALL	STP	7330 KB
CAD Portal / CAD Portal	ALL	LINK	---
CAE
CAE EPLAN Data Portal / CAE EPLAN Data Portal	ALL	LINK	---
EPLAN macro EDZ / EPLAN Makro EDZ	ALL	EDZ	2213 KB

Approvals: FB8211H0756.3

Certificates	Cert No.	Language	File Type	File Size
Brasil TUV Rheinland Brazil	TÜV 19.0480 U	ALL	PDF	1258 KB
China SITIIAS CCC Ex Certificate	2021322310004115 (Mannheim)	ALL	PDF	2333 KB
Europe Presafe DNV GL II 2(1)G I (M1) ATEX II (1) D	Presafe 19 ATEX 14058U	ALL	PDF	607 KB
Presafe DNV GL IECEx Certificate of Conformity	IECEx PRE 19.0013U	ALL	LINK	---
Declaration of Conformity
EU Declaration of Conformity (P+F)	TDOC-4263DENG	ENG	PDF	1142 KB
UK Declaration of Conformity (P+F)	TDOC-6753_ENG	ENG	PDF	1110 KB

Software: FB8211H0756.3

Firmware	Release Info	File Type	File Size
Firmware for Comm Units 8x11 / Firmware für Buskoppler 8x11	7.56	ZIP	1615 KB
Firmware for Comm Units 8x11 / Firmware für Buskoppler 8x11	7.55	ZIP	1606 KB
Service-Tool / Service-Tool	3.00.0003	ZIP	5185 KB

Associated Products: FB8211H0756.3

Accessories

	DTM LB/FB DTM collection
	Device DTM, For Remote I/O systems, Frame application, like e. g. PACTware, must be installed separatelypa

General Notes Relating to Pepperl+Fuchs Product Information

Quick Links

Pepperl+Fuchs (Aust) Pty Ltd
131-149 Link Drive
Campbellfield, Victoria
Melbourne, Victoria 3061
Australia
sales@au.pepperl-fuchs.com
phone +61 3 9358 3400

Pepperl+Fuchs is a leading developer and manufacturer of electronic sensors and components for the global automation market. Continuous innovation, enduring quality, and steady growth have been the foundation of our success for more than 70 years. Pepperl+Fuchs employs 6,300 people worldwide and has manufacturing facilities in Germany, USA, Singapore, Hungary, Indonesia and Vietnam, most of them ISO 9001 certified.