NCN25-F35-A2-250-V1 Inductive sensor

Key Benefits at a Glance

Comfort series
Extended temperature range of sensor component
0 ... 250 °C (0 ... 482 °F)
10 m cable between sensor and amplifier with metal case
Suitable for drag chains and abrasion resistant
Minimum bending radius of 30 cm for movable installation

Product photo: Inductive sensor NCN25-F35-A2-250-V1

Dimensions: Inductive sensor NCN25-F35-A2-250-V1

Note

All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.

Datasheet Classification Product Documentation Design / Simulation Approvals Related Products

Technical data of NCN25-F35-A2-250-V1

Switching function		complementary
Output type		PNP
Rated operating distance	s_n	25 mm
Installation		flush mountable
Output polarity		DC
Assured operating distance	s_a	0 ... 20 mm
Reduction factor r_Al		0.5
Reduction factor r_Cu		0.5
Reduction factor r₃₀₄		0.6 ... 1
Output type		4-wire
Mounting angle		Al
Amplifier housing		Stainless steel

Operating voltage	U_B	10 ... 30 V
Switching frequency	f	0 ... 20 Hz
Hysteresis	H	0.3 ... 5 typ. 2 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop	U_d	≤ 3 V
Operating current	I_L	0 ... 200 mA
No-load supply current	I₀	≤ 25 mA
Time delay before availability	t_v	≤ 20 ms
Switching state indicator		Multihole-LED, yellow

MTTF_d		7515 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %

Standard conformity

Standards

EN IEC 60947-5-2

UL approval		cULus Listed, General Purpose, Class 2 Power Source
CCC approval		CCC approval / marking not required for products rated ≤36 V

Ambient temperature

0 ... 250 °C (32 ... 482 °F)

Connection type

Connector plug M12 x 1 , 4-pin

Cable version

PFA cable, with armour of stainless steel

Core cross section

3 x 0.34 , screened

Housing material

PTFE / Al / 1.4305 / AISI 303

Sensing face

PTFE

Degree of protection

amplifier IP67
sensor IP40

Dimensions

Height		40 mm
Width		44 mm
Length		56 mm

Cable length

L = 10 m

Note

- amplifier 0 °C ... 70 °C
- r_1.4305 dep. on thickness of measurement plate d:
r_1.4305 = 1 for d < 1mm
Additional accessory: Protective cover SH-F35 is available for use in areas where there is moisture and as a means of mechanical protection.

General Notes

We value your privacy!

We and our partners are using technologies like cookies and process personal data like the IP-address or browser information in order to personalize the advertising that you see. This helps us to show you more relevant ads and improves your internet experience. We also use it in order to measure results or align our website content. Because we value your privacy, we are herewith asking for your permission to use these technologies. You can always change/withdraw your consent later by clicking on the settings button on the left lower corner of the page.

Categories	Description	Status
Functional	These cookies are necessary so that you can navigate through the pages and use essential functions (e.g. login).
Analytics	We use these cookies and scripts to measure the visits and clicks on our website in order to constantly improve it.
Marketing	These cookies and similar technologies are used to provide you with personalized and therefore relevant advertising content.