Select Your Country

Go to global website

  1. en
  2. Products
  3. Hazardous Area Products and Solutions
  4. Intrinsic Safety Barriers
  5. H-System (Termination Board mounting)
  6. HiC2065

Archived Product Version

HiC2065 Voltage Repeater

Key Benefits at a Glance

  • 1-channel isolated barrier
  • 24 V DC supply (bus powered)
  • Voltage input 0 mV ... ± 50 mV
  • Voltage output 0 mV ... ± 50 mV
  • Selectable up/downscale sensor breakage detection
  • Fault output signal

Show more

Please contact us for exact delivery estimation.
Product photo: Voltage Repeater HiC2065
Product photo: Voltage Repeater HiC2065
Approval
Product Compliance: USA - cULus
Approval
Product Compliance: Europe – CE
Note

All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.

EN
  • DE
  • EN
  • ES
  • FR
  • PL
DatasheetFunctionClassificationProduct DocumentationDesign / SimulationApprovals

Technical data of HiC2065

Signal typeAnalog input
ConnectionSL1: 1a, 1b(-); 2a, 2b(+)
Rated voltageUr20 ... 30 V DC bus powered via Termination Board
Ripplewithin the supply tolerance
Rated currentIr≤ 22 mA
Power dissipation/power consumption0.7 W max.
Lockout voltage> 11 V DC
Connection sidefield side
ConnectionSL2: 5a(+), 5b(-)
Input resistance≥ 16 MΩ
Transmission range0 ... ± 50 mV
Offset voltage/current≤ 5 µV / ≤ 5 nA
Connection sidecontrol side
ConnectionSL1: 8a(+), 7a(-)
Voltage0 ... ± 50 mV
LoadAccuracy figures for infinite load impedance. Additional 0.03 % of span for a load resistance of 10 kΩ
Output resistancemax. 3 Ω
Line fault detectioninput: ± 100 mV
output: +200 mV, -115 mV
ConnectionSL1: 6b
Output typeopen collector transistor (internal fault bus)
Fault voltage< Vcc/2 (when connected to Vcc via 10 kΩ pull up resistor)
Deviation
After calibrationat 20 °C (68 °F):
± 3 µV up to ± 10mV/± 0.05 % of the span up to +50 mV/± 0.05 % of the span up to -50 mV
Influence of ambient temperature± 1 µV/K (typical ± 0.25 µV/K)
Absolute< 0.25 K at 30 V voltage supply
BandwidthDC to > 350 Hz (-3 dB)
Settling time< 2 ms
Rise time/fall time≤ 1 ms
Output/power supplyfunctional insulation, rated insulation voltage 50 V AC
Display elementsLEDs
Control elementsDIP switch
Configurationvia DIP switches
Labelingspace for labeling at the front
Electromagnetic compatibility
Directive 2014/30/EUEN 61326-1:2013 (industrial locations)
Electromagnetic compatibilityNE 21:2006
For further information see system description.
Degree of protectionIEC 60529:2001
Protection against electrical shockUL 61010-1
Ambient temperature-20 ... 60 °C (-4 ... 140 °F)
Degree of protectionIP20
Massapprox. 100 g
Dimensions12.5 x 106 x 128 mm (0.5 x 4.2 x 5.1 inch) (W x H x D)
Height106 mm
Width12.5 mm
Depth128 mm
Mountingon termination board
Codingpin 2, 3 and 4 trimmed
For further information see system description.
EU-type examination certificateBASEEFA 10 ATEX 0031X
MarkingEx-Hexagon II (1)GD, I (M1), [Ex ia] IIC, [Ex iaD], [Ex ia] I (-20 °C ≤ Tamb ≤ 60 °C) [circuit(s) in zone 0/1/2]
VoltageUo5.5 V DC
CurrentIo2.4 mA
PowerPo3.3 mW
Supply
Maximum safe voltageUm253 V (Attention! The rated voltage can be lower.)
CertificateBASEEFA 10 ATEX 0032X
MarkingEx-Hexagon II 3G Ex nA II T4
Galvanic isolation
Input/Outputsafe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
Input/power supplysafe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
Directive conformity
Directive 2014/34/EUEN 60079-0:2012+A11:2013 , EN 60079-11:2012 , EN 60079-15:2010
UL approval
Control drawing116-0317 (cULus)
IECEx approval
IECEx certificateIECEx BAS 10.0012X
IECEx BAS 10.0013X
IECEx marking[Zone 0] [Ex ia] IIC, [Ex iaD], [Ex ia] I
Ex nA II T4
Supplementary informationObserve the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.
General Notes

Related News and Applications

Read more on news and applications related to this product.

HiC2422 isolated barrier for analog signals, Pepperl+Fuchs
Products and Solutions
4/2/2024

New Universal Isolated Barrier for Analog Signals: HiC2422

The new H-System HiC2422 intrinsic safety barrier has two freely configurable channels for analog signals, which means it can be used both as a SMART transmitter power supply for two-wire transmitters and as a current driver for valve positioners.
More information

We value your privacy!

We and our partners are using technologies like cookies and process personal data like the IP-address or browser information in order to personalize the advertising that you see. This helps us to show you more relevant ads and improves your internet experience. We also use it in order to measure results or align our website content. Because we value your privacy, we are herewith asking for your permission to use these technologies. You can always change/withdraw your consent later by clicking on the settings button on the left lower corner of the page.

Privacy Policy

Deny all cookies