Not available for purchase
AS-Interface I/O module VBA-4E3A-G20-ZEL/E2L-P8-GEB
- A/B slave with extended addressing possibility for up to 62 slaves
- Power supply of the inputs and outputs from the external auxiliary voltage
- Communication monitoring
- Function display for bus, external auxiliary voltage, in- and outputs
- Cable piercing method with gold plated contact pins
Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.
Download the complete datasheet as a PDF:
Datasheet excerpt: Technical data of VBA-4E3A-G20-ZEL/E2L-P8-GEB
| Product Description |
|---|
| G20 module 4 inputs/3 outputs |
| General specifications | ||
|---|---|---|
| Node type | A/B node | |
| AS-Interface specification | V3.0 | |
| Required gateway specification | ≥ V2.1 | |
| UL File Number | E223772 "For use in NFPA 79 Applications only" | |
| MTBF | 110 a | |
| Indicators/operating means | ||
| LED FAULT | Fault indication; red LED Red: communication error or address is 0 Flashing red: overload at motor supply or overload at outputs, or external auxiliary voltage UAUX not present |
|
| LED PWR | AS-Interface voltage; green LED Green: voltage OK Flashing green: address is 0 or overload at motor supply, or overload at outputs, or external auxiliary voltage UAUX not present |
|
| LED AUX | ext. auxiliary voltage UAUX; dual LED green/red green: voltage OK red: reverse voltage |
|
| LED IN | switching state (input); 4 LED yellow | |
| LED OUT | Switching state (output); 3 LED yellow | |
| Electrical specifications | ||
| Auxiliary voltage (output) | 20 ... 30 V DC PELV | |
| Rated operating voltage | 26.5 ... 31.6 V from AS-Interface | |
| Rated operating current | ≤ 35 mA | |
| Input | ||
| Number/Type | 4 Inputs (PNP), DC | |
| Supply | from external auxiliary voltage UAUX | |
| Input current | ≤ 8 mA (limited internally) | |
| Switching point | according to DIN EN 61131-2 0 (undamped) ≤ 0.5 mA 1 (damped) ≥ 2.0 mA |
|
| Signal delay | < 1 ms (input/AS-Interface) | |
| Output 1 | ||
| Number/Type | 3 electronic outputs, PNP, overload and short-circuit proof | |
| Supply | from external auxiliary voltage UAUX | |
| Current | 500 mA per output | |
| Voltage | ≥ (UAUX - 0.5 V) | |
| Output 2 | ||
| Number/Type | Motor supply | |
| Supply | from external auxiliary voltage UAUX | |
| Current | TB < 40 °C: 2 A continuously, 5 A briefly (< 0.5 s) TB < 60 °C: 2 A continuously, 3 A briefly (< 0.5 s) |
|
| Voltage | ≥ (UAUX - 0.5 V) | |
| Directive conformity | ||
| Electromagnetic compatibility | ||
| Directive 2014/30/EU | EN 62026-2:2013 | |
| Standard conformity | ||
| Degree of protection | EN 60529:2000 | |
| Fieldbus standard | EN 62026-2:2013 | |
| Input | EN 61131-2:2007 | |
| Emitted interference | EN 61000-6-4:2007 | |
| Noise immunity | EN 61000-6-2:2005, EN 61326-1:2006, EN 62026-2:2013 | |
| Programming instructions | ||
| Profile | S-7.A.E | |
| IO code | 7 | |
| ID code | A | |
| ID1 code | 7 | |
| ID2 code | E | |
| Data bits (function via AS-Interface) | ||
| D0 | ||
| D1 | ||
| D2 | ||
| D3 | ||
| Parameter bits (programmable via AS-i) | function | |
| P0 | Communication monitoring P0 = 0 monitoring = off, the outputs maintain the status if communication fails P0 = 1 monitoring = on, i.e. if communication fails, the outputs are deenergised (default settings) |
|
| P1 | Input filter P1 = 0 input filter on, pulse suppression ≤ 2 ms P1 = 1 input filter off (default settings) |
|
| P2 | Synchronous mode P2 = 0 synchronous mode on P2 = 1 synchronous mode off (default settings) |
|
| Ambient conditions | ||
| Ambient temperature | -25 ... 60 °C (-13 ... 140 °F) | |
| Storage temperature | -25 ... 85 °C (-13 ... 185 °F) | |
| Mechanical specifications | ||
| Degree of protection | IP54 according to EN 60529 | |
| Connection | AS-Interface, AUX: Insulation piercing technology Yellow flat cable/black flat cable Inputs/outputs: 8-pin M8 round plug connector, bushing contacts, screw-locking Motor supply: 4-pin M12 round plug connector, bushing contacts, screw-locking, T-coded |
|
| Mass | 260 g | |
| Dimensions | ||
| Height | 27.5 mm | |
| Width | 152 mm | |
| Length | 53.3 mm | |
| Mounting | 2 clips with ∅ 8 mm drill hole | |
| Cable length | 1 m | |
| Note | The flat cable routing is designed for 100 actuation cycles | |
Classifications
| System | Classcode |
|---|---|
| ECLASS 13.0 | 27242604 |
| ECLASS 12.0 | 27242604 |
| ECLASS 11.0 | 27242604 |
| ECLASS 10.0.1 | 27242604 |
| ECLASS 9.0 | 27242604 |
| ECLASS 8.0 | 27242604 |
| ECLASS 5.1 | 27242604 |
| ETIM 9.0 | EC001599 |
| ETIM 8.0 | EC001599 |
| ETIM 7.0 | EC001599 |
| ETIM 6.0 | EC001599 |
| ETIM 5.0 | EC001599 |
| UNSPSC 12.1 | 39121535 |
Details: VBA-4E3A-G20-ZEL/E2L-P8-GEB
Product Documentation: VBA-4E3A-G20-ZEL/E2L-P8-GEB
| Brief Instructions | Language | File Type | File Size |
|---|---|---|---|
| Instruction leaflet / Beipackzettel | ALL | 557 KB |
Design / Simulation: VBA-4E3A-G20-ZEL/E2L-P8-GEB
| CAE | Language | File Type | File Size |
|---|---|---|---|
| CAE EPLAN macro EDZ / CAE EPLAN Makro EDZ | ALL | EDZ | 364 KB |
Associated Products: VBA-4E3A-G20-ZEL/E2L-P8-GEB
| Accessories | ||||||
|---|---|---|---|---|---|---|
|
||||||
|
||||||
|
||||||
This free PDF white paper compares the different TCP-based communication protocols (AMQP, OPC UA, MQTT, REST API) that have found their way up and are considered the enablers of IIoT and Industry 4.0. Get your free download now!
AS-Interface Switch Cabinet Module KE5 – Simple Handling and Improved Manageability
The unique housing design of the new KE5 switch cabinet module enables distinct visibility and simplifies mounting, wiring, and maintenance inside switch cabinets and junction boxes.
Pepperl+Fuchs GB Ltd.
77 Ripponden Road
Oldham OL1 4EL, Lancs.
United Kingdom
sales@gb.pepperl-fuchs.com
+44 161 6336431
Pepperl+Fuchs is a leading developer and manufacturer of electronic sensors and components for the global automation market. Continuous innovation, enduring quality, and steady growth have been the foundation of our success for more than 70 years. Pepperl+Fuchs employs 6,300 people worldwide and has manufacturing facilities in Germany, USA, Singapore, Hungary, Indonesia and Vietnam, most of them ISO 9001 certified.