Solenoid Driver HiD2872
- 2-channel isolated barrier
- 24 V DC supply (bus or loop powered)
- Output 40 mA at 12 V DC, 55 mA current limit
- Contact or logic control input
- Entity parameter Io/Isc = 110 mA
- Line fault detection (LFD)
- Up to SIL 2 acc. to IEC/EN 61508 (bus powered)
- Up to SIL 3 acc. to IEC/EN 61508 (loop powered)
Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.
Download the complete datasheet as a PDF:
Datasheet excerpt: Technical data of HiD2872
| General specifications | ||
|---|---|---|
| Signal type | Digital Output | |
| Functional safety related parameters | ||
| Safety Integrity Level (SIL) | SIL 3 | |
| Supply | ||
| Connection | SL1: 1a(-), 1b(-); 2a(+), 2b(+) | |
| Rated voltage | 20.4 ... 30 V DC loop powered 20.4 ... 30 V DC bus powered via Termination Board |
|
| Input current | 62 mA at 24 V, 300 Ω load (per channel) | |
| Power dissipation | 1 W at 24 V, 300 Ω load (per channel) | |
| Input | ||
| Connection side | control side | |
| Connection | SL1: 8a(+), 7a(-); 10a(+), 9a(-) bus powered SL1: 8b(+), 7b(-); 9b(+), 10b(-) loop powered |
|
| Control input | external switch (dry contact or open collector) non isolated or logic signal input fully floating | |
| Signal level | 1-signal: 15...30 V DC (current limited to 3 mA) or contact close (internal 10 kΩ pull-up) 0-signal: 0...5 V DC or contact open |
|
| Power dissipation | 1 W at 24 V, 300 Ω load (per channel) for loop powered | |
| Inrush current | 0.2 A , 15 ms loop powered | |
| Output | ||
| Connection side | field side | |
| Connection | SL2: 5a(+), 5b(-), 7a(+); 1a(+), 1b(-), 3b(+) | |
| Internal resistor | approx. 240 Ω | |
| Current | ≤ 40 mA | |
| Voltage | ≥ 12 V | |
| Current limit | 55 mA | |
| Open loop voltage | approx. 22.5 V | |
| Load | nominal 0.1 ... 5 kΩ | |
| Switching frequency | - bus powered: filter OFF: max. 150 Hz, filter ON: max. 15 Hz - loop powered: max. 10 Hz |
|
| Energized/De-energized delay | - bus powered: filter OFF: 1 ms, filter ON: 10 ms - loop powered: switch-on 50 ms, switch-off 6 ms (300 Ω load) |
|
| Fault indication output | ||
| Connection | SL1: 6b | |
| Output type | open collector transistor (internal fault bus) | |
| Fault current | 4 mA pulsing (20 ms ON, 200 ms OFF) | |
| Fault level | lead short-circuit detection at < 25 Ω lead breakage detection at > 100 kΩ typical |
|
| Galvanic isolation | ||
| Output/Output | safe electrical isolation acc. to EN 60079-11: 2007, voltage peak value 60 V | |
| Output/power supply, inputs, and collective error | safe electrical isolation acc. to EN 60079-11: 2007, voltage peak value 375 V | |
| Indicators/settings | ||
| Display elements | LEDs | |
| Control elements | DIP switch | |
| Configuration | via DIP switches | |
| Labeling | space for labeling at the front | |
| Directive conformity | ||
| Electromagnetic compatibility | ||
| Directive 2014/30/EU | EN 61326-1:2013 (industrial locations) | |
| Conformity | ||
| Electromagnetic compatibility | NE 21:2006 For further information see system description. |
|
| Degree of protection | IEC 60529:2001 | |
| Ambient conditions | ||
| Ambient temperature | -20 ... 60 °C (-4 ... 140 °F) | |
| Relative humidity | 5 ... 90 %, non-condensing up to 35 °C (95 °F) | |
| Mechanical specifications | ||
| Degree of protection | IP20 | |
| Mass | approx. 140 g | |
| Dimensions | 18 x 114 x 130 mm (0.7 x 4.5 x 5.1 inch) (W x H x D) | |
| Height | 114 mm | |
| Width | 18 mm | |
| Depth | 130 mm | |
| Mounting | on termination board | |
| Coding | pin 1 and 4 trimmed For further information see system description. |
|
| Data for application in connection with hazardous areas | ||
| EU-type examination certificate | CESI 10 ATEX 036 | |
| Marking |  II (1)G [Ex ia Ga] IIC II (1)D [Ex ia Da] IIIC I (M1) [Ex ia Ma] I |
|
| Output | Ex ia Ga, Ex ia Da, Ex ia Ma | |
| Voltage | 26 V | |
| Current | 110 mA | |
| Power | 715 mW | |
| Supply | ||
| Maximum safe voltage | 253 V AC (Attention! Um is no rated voltage.) | |
| Certificate | PF 10 CERT 1729 X | |
| Marking | II 3G Ex nA IIC T4 Gc |
|
| Directive conformity | ||
| Directive 2014/34/EU | EN 60079-0:2012+A11:2013 , EN 60079-11:2012 , EN 60079-15:2010 | |
| International approvals | ||
| CSA approval | ||
| Control drawing | 366-005CS-12B (cCSAus) | |
| IECEx approval | ||
| IECEx certificate | IECEx CES 10.0013 | |
| IECEx marking | [Ex ia Ga] IIC, [Ex ia Da] IIIC, [Ex ia Ma] I | |
| General information | ||
| Supplementary information | Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com. | |
Classifications
| System | Classcode |
|---|---|
| ECLASS 13.0 | 27210101 |
| ECLASS 12.0 | 27210190 |
| ECLASS 11.0 | 27210190 |
| ECLASS 10.0.1 | 27210190 |
| ECLASS 9.0 | 27210190 |
| ECLASS 8.0 | 27210190 |
| ECLASS 5.1 | 27210121 |
| ETIM 9.0 | EC001485 |
| ETIM 8.0 | EC001485 |
| ETIM 7.0 | EC001485 |
| ETIM 6.0 | EC001485 |
| ETIM 5.0 | EC001485 |
| UNSPSC 12.1 | 39121008 |
Details: HiD2872
Function
This isolated barrier is used for intrinsic safety applications.
It supplies power to solenoids, LEDs, and audible alarms, located in a hazardous area.
It is controlled with a loop-powered control signal, switch contact, transistor, or logic signal.
At full load, 12 V at 40 mA (with 55 mA current limit) is available for the hazardous area application.
An alternative low current output is available for driving a single LED without installing an external current limiting resistor.
Line fault detection of the field circuit is indicated by a red LED and an output on the fault bus.
This device mounts on a HiD Termination Board.
Product Documentation: HiD2872
| Product information | Language | File Type | File Size |
|---|---|---|---|
| Application Guideline Solenoid Drivers | ENG | 734 KB | |
| Safety and Security Documentation | |||
| Instruction manual | ENG | 168 KB | |
| Functional Safety Manual | ENG | 1399 KB | |
| Manuals | |||
| System Manual | ENG | 5438 KB | |
Design / Simulation: HiD2872
| CAD | Language | File Type | File Size |
|---|---|---|---|
| CAD 2-D / CAD 2-D | ALL | ZIP | 16364 KB |
| CAE | |||
| EPLAN macros H-System devices (EMA) / EPLAN-Makros Geräte H-System (EMA) | ALL | ZIP | 3536 KB |
Approvals: HiD2872
| Certificates | Certificate No. | Language | File Type | File Size |
|---|---|---|---|---|
| CESI IECEx Certificate of Conformity | IECEx CES 10.0013 | ALL | LINK | --- |
| Canada, USA CSA | CoC 70001345 | ALL | 136 KB | |
| Europe CESI ATEX Category (1) D ATEX Category (M1) ATEX Category (1) G | CESI 10 ATEX 036 | ALL | 1416 KB | |
| Europe Pepperl+Fuchs Certificate of Compliance ATEX Category 3 | PF 10 CERT 1729X | ALL | 206 KB | |
| exida Functional Safety Assessment | P+F 11/07-044 R034 V1R2 | ALL | 577 KB | |
| Control Drawings | ||||
| Control drawing CSA / Control drawing CSA | ALL | 98 KB | ||
| Declaration of Conformity | ||||
| EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F) | DOC-0931B | ALL | 52 KB | |
Choose from various selection criteria like safety integrity level, performance level, device function, and signal type and find the SIL/PL assessed device that you are looking for.
Pepperl+Fuchs GB Ltd.
77 Ripponden Road
Oldham OL1 4EL, Lancs.
United Kingdom
sales@gb.pepperl-fuchs.com
+44 161 6336431
Pepperl+Fuchs is a leading developer and manufacturer of electronic sensors and components for the global automation market. Continuous innovation, enduring quality, and steady growth have been the foundation of our success for more than 70 years. Pepperl+Fuchs employs 6,300 people worldwide and has manufacturing facilities in Germany, USA, Singapore, Hungary, Indonesia and Vietnam, most of them ISO 9001 certified.