Ultrasonic sensor UC800-F77S-IU-IO-V31-P001
- IO-Link interface for parameterization
- Programmable via DTM with PACTWARE
- Selectable sound lobe width
- Synchronization options
- Temperature compensation
- Analog output
- Customer-specific configuration
Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.
Download the complete datasheet as a PDF:
Datasheet excerpt: Technical data of UC800-F77S-IU-IO-V31-P001
| Product Description |
|---|
| Single head system |
| General specifications | ||
|---|---|---|
| Sensing range | 100 ... 800 mm | |
| Adjustment range | 100 ... 800 mm | |
| Dead band | 0 ... 100 mm | |
| Standard target plate | 100 mm x 100 mm | |
| Transducer frequency | approx. 255 kHz | |
| Response delay | minimum : 13 ms factory setting: 49 ms |
|
| Sensor cycle time | ≥ 13 ms (factory setting) ; programmable to 60 s |
|
| Memory | ||
| Non-volatile memory | EEPROM | |
| Write cycles | 300000 | |
| Indicators/operating means | ||
| LED green | solid: power on flashing: standby mode or IO-Link communication |
|
| LED yellow | solid: object in evaluation range flashing: programming of the limits, object detected |
|
| LED red | solid: fault flashing: programming limits, object not detected |
|
| Electrical specifications | ||
| Operating voltage | 18 ... 30 V DC , ripple 10 %SS |
|
| No-load supply current | ≤ 50 mA | |
| Power consumption | ≤ 500 mW | |
| Time delay before availability | ≤ 300 ms | |
| Interface | ||
| Interface type | IO-Link (available after activation via programming button until next reset) | |
| Input/Output | ||
| Input/output type | 1 synchronization connection, bidirectional | |
| 0 Level | 0 ... 1 V | |
| 1 Level | 2.5 V ... UB | |
| Input impedance | > 22 kΩ | |
| Output current | current source < 2.5 mA | |
| Pulse length | ≥ 1 ms with external control, low active | |
| Synchronization frequency | ||
| Common mode operation | ≤ 82 Hz | |
| Multiplex operation | ≤ 82 Hz / n , n = number of sensors , n ≤ 10 |
|
| Output | ||
| Output type | 1 analog output 0 (4) ... 20 mA or 1 analog output 0 ... 10 V |
|
| Resolution | current output: evaluation range [mm]/3200 but ≥ 0.35 mm voltage output: evaluation range [mm]/4000 but ≥ 0.35 mm |
|
| Deviation of the characteristic curve | ≤ ± 1 % of full-scale value | |
| Repeat accuracy | ≤ ± 0.1 % of full-scale value | |
| Load impedance | current output: ≤ 500 Ohm voltage output: ≥ 1000 Ohm |
|
| Temperature influence | ≤ ± 0.75 % of the end value (with temperature compensation) from 10 minutes after switching on the sensor ; 0.17 %/K (without temperature compensation) | |
| Compliance with standards and directives | ||
| Standard conformity | ||
| Standards | EN IEC 60947-5-2:2020 IEC 60947-5-2:2019 EN 60947-5-7:2003 IEC 60947-5-7:2003 IEC 61131-9:2013 |
|
| Approvals and certificates | ||
| UL approval | cULus Listed, Class 2 Power Source | |
| CCC approval | CCC approval / marking not required for products rated ≤36 V | |
| Ambient conditions | ||
| Ambient temperature | current output -25 ... 60 °C (-13 ... 140 °F) voltage output -25 ... 70 °C (-13 ... 158 °F) When fixing with one M18 nut, the temperature range for each begins with 0 °C (32 °F). |
|
| Storage temperature | -40 ... 85 °C (-40 ... 185 °F) | |
| Mechanical specifications | ||
| Connection type | Connector plug M8 x 1 , 4-pin | |
| Degree of protection | IP67 | |
| Material | ||
| Housing | Polycarbonate | |
| Transducer | epoxy resin/hollow glass sphere mixture; polyurethane foam | |
| Installation position | any position | |
| Mass | 13 g | |
| Tightening torque, fastening screws | with M3 nuts max. 0.2 Nm with M18 nuts max. 1 Nm |
|
| Dimensions | ||
| Height | 31 mm | |
| Width | 21 mm | |
| Length | 23 mm | |
| Factory settings | ||
| Output | near limit: 100 mm far limit: 800 mm Output mode: rising ramp output type: 4 ... 20 mA |
|
| Beam width | wide | |
Classifications
| System | Classcode |
|---|---|
| ECLASS 13.0 | 27272803 |
| ECLASS 12.0 | 27272803 |
| ECLASS 11.0 | 27272803 |
| ECLASS 10.0.1 | 27272803 |
| ECLASS 9.0 | 27272803 |
| ECLASS 8.0 | 27272803 |
| ECLASS 5.1 | 27272803 |
| ETIM 9.0 | EC001849 |
| ETIM 8.0 | EC001849 |
| ETIM 7.0 | EC001849 |
| ETIM 6.0 | EC001849 |
| ETIM 5.0 | EC001849 |
| UNSPSC 12.1 | 41111960 |
Details: UC800-F77S-IU-IO-V31-P001
Product Documentation: UC800-F77S-IU-IO-V31-P001
| Brief Instructions | Language | File Type | File Size |
|---|---|---|---|
| Commissioning instruction for UC*-F77*-IU* / Inbetriebnahmeanleitung für UC*-F77*-IU* | ALL | 440 KB | |
| Manuals | |||
| Manual UC***-F77 Series Parameterization of Ultrasonic Sensors with IO-Link Interface | ENG | 4224 KB | |
Design / Simulation: UC800-F77S-IU-IO-V31-P001
| CAD | Language | File Type | File Size |
|---|---|---|---|
| CAD 3-D / CAD 3-D | ALL | STP | 1739 KB |
| CAE | |||
| EPLAN macro EDZ / EPLAN Makro EDZ | ALL | EDZ | 63 KB |
Software: UC800-F77S-IU-IO-V31-P001
| Software Tools | Release Info | File Type | File Size |
|---|---|---|---|
| PACTware 4.1 SP6 / PACTware 4.1 SP6 | 4.1.0.53 | ZIP | 43327 KB |
| PACTware 5.0 / PACTware 5.0 | 5.0.5.31 | ZIP | 44203 KB |
| Pepperl+Fuchs PACTware Connection Wizard (Add-In for parameterization software PACTware) / Pepperl+Fuchs PACTware Connection Wizard (Add-In für Parametriersoftware PACTware) | 1.0.0.3 | ZIP | 295 KB |
Associated Products: UC800-F77S-IU-IO-V31-P001
| Accessories | ||||||
|---|---|---|---|---|---|---|
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
The USi-safety ultrasonic sensor system is breaking new ground for safety applications—whether in challenging, dusty environments or in outdoor areas.
Pepperl+Fuchs offers you various downloadable documents containing knowledge on ultrasonic sensors.
Pepperl+Fuchs (India) Pvt. Ltd.
Ground Floor, #546/1, Sy. No. 46, 7th Main
4th Phase, Peenya Industrial Estate
Bangalore - 560058
India
info@in.pepperl-fuchs.com
+91 80 4609 6000
© 2024 All Rights Reserved.
Pepperl+Fuchs is a leading developer and manufacturer of electronic sensors and components for the global automation market. Continuous innovation, enduring quality, and steady growth have been the foundation of our success for more than 70 years. Pepperl+Fuchs employs 6,300 people worldwide and has manufacturing facilities in Germany, USA, Singapore, Hungary, Indonesia and Vietnam, most of them ISO 9001 certified.