| General specifications |
| Signal type | Digital Output |
| Functional safety related parameters |
| Safety Integrity Level (SIL) | SIL 3 |
| Supply |
| Connection | Power Rail or terminals 14+, 15- |
| Rated voltage | 19 ... 30 V DC |
| Rated current | < 35 mA |
| Power consumption | < 0.8 W |
| Input |
| Connection side | control side |
| Connection | terminals 10+, 11- |
| Input current | 40 mA at 19 ... 30 V DC |
| Signal level | 1-signal: 19 ... 30 V DC
0-signal: 0 ... 5 V DC |
| Power consumption | < 1.2 W |
| Operating mode | loop powered |
| Output |
| Connection side | field side/control side |
| Connection | terminals 1+, 3- (terminals 1+, 2 for test loop) |
| Internal resistor | approx. 275 Ω |
| Current | ≤ 20.4 mA |
| Voltage | ≥ 13.5 V |
| Open loop voltage | > 16 V |
| Voltage | 1-signal: > 13.5 V |
| Current | 1-signal: 20.4 A
0-signal: 4.2 mA |
| Load | max. 650 Ω |
| Response time | < 40 ms input to output |
| Line fault detection | short circuit voltage < 1 V , open circuit voltage > 16 V |
| Output II | |
| Connection | terminal 7: source (-) or sink (+), terminal 8: source (+), terminal 9: sink (-) |
| Current | 11 mA (source or sink mode) |
| Voltage | 9 ... 30 V sink mode from external supply |
| Load | max. 650 Ω , source mode , for HART ≥ 230 Ω |
| Communication | pass-through of HART signal between input II and output |
| Galvanic isolation |
| Input/power supply | functional insulation acc. to IEC 62103, rated insulation voltage 50 Veff |
| Output II/power supply | functional insulation acc. to IEC 62103, rated insulation voltage 50 Veff |
| Indicators/settings |
| Display elements | LEDs |
| Control elements | DIP switch |
| Configuration | via DIP switches |
| Labeling | space for labeling at the front |
| Directive conformity |
| Electromagnetic compatibility | |
| Directive 2014/30/EU | EN 61326-1:2013 (industrial locations) |
| Conformity |
| Electromagnetic compatibility | NE 21:2012 |
| Degree of protection | IEC 60529:2001 |
| Ambient conditions |
| Ambient temperature | -20 ... 60 °C (-4 ... 140 °F) |
| Mechanical specifications |
| Degree of protection | IP20 |
| Connection | screw terminals |
| Mass | approx. 150 g |
| Dimensions | 20 x 119 x 115 mm (0.8 x 4.7 x 4.5 inch) (W x H x D) , housing type B2 |
| Height | 119 mm |
| Width | 20 mm |
| Depth | 115 mm |
| Mounting | on 35 mm DIN mounting rail acc. to EN 60715:2001 |
| Data for application in connection with hazardous areas |
| EU-type examination certificate | CESI 09 ATEX 037 |
| Marking |  II (1)GD [Ex ia] IIC; [Ex iaD] [circuit(s) in zone 0/1/2/20/21/22] |
| Equipment | terminals 1+, 2 / 3- |
| Voltage | 24.5 V |
| Current | 93.6 mA |
| Power | 595 mW (linear characteristic) |
| Supply | |
| Maximum safe voltage | 253 V (Attention! The rated voltage can be lower.) |
| Input | |
| Maximum safe voltage | 253 V (Attention! The rated voltage can be lower.) |
| Collective error message | |
| Maximum safe voltage | 253 V (Attention! The rated voltage can be lower.) |
| Certificate | PF 09 CERT 1438 X |
| Marking | II 3G Ex nA IIC T4 Gc |
| Galvanic isolation | |
| Output I/other circuits | safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V |
| Directive conformity | |
| Directive 2014/34/EU | EN 60079-0:2012+A11:2013 , EN 60079-11:2012 , EN 60079-15:2010 |
| International approvals |
| CSA approval | |
| Control drawing | 116-0335 |
| IECEx approval | |
| IECEx certificate | IECEx CES 09.0008 |
| IECEx marking | [Ex ia] IIC , [Ex iaD] |
| General information |
| Supplementary information | Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com. |
+31 73 75 07 107