General specifications |
Sensing range | 60 ... 800 mm |
Adjustment range | 70 ... 800 mm |
Dead band | 0 ... 60 mm |
Standard target plate | 100 mm x 100 mm |
Transducer frequency | approx. 255 kHz |
Response delay | minimum : 13 ms factory setting: 49 ms |
Sensor cycle time | ≥ 13 ms (factory setting) ; programmable to 60 s |
Memory |
Non-volatile memory | EEPROM |
Write cycles | 300000 |
Indicators/operating means |
LED green | solid: power on flashing: standby mode or IO-Link communication |
LED yellow | solid: object in evaluation range flashing: switch point programming, object detected |
LED red | solid: error flashing: switch point programming, object not detected |
Electrical specifications |
Operating voltage | 10 ... 30 V DC , ripple 10 %SS |
No-load supply current | ≤ 40 mA |
Power consumption | ≤ 400 mW |
Time delay before availability | ≤ 300 ms |
Interface |
Interface type | IO-Link (via C/Q = Pin 4) |
IO-Link revision | 1.1 |
Device profile | Smart Sensor |
Device ID | 0x300302 (3146498) |
Transfer rate | COM2 (38.4 kBit/s) |
Min. cycle time | 2.3 ms |
Process data width | 16 bit |
SIO mode support | yes |
Compatible master port type | A |
Input/Output |
Input/output type | 1 synchronization connection, bidirectional |
| 0 Level | 0 ... 1 V |
| 1 Level | 2.5 V ... UB |
| Input impedance | > 22 kΩ |
| Output current | current source < 2.5 mA |
| Pulse length | ≥ 1 ms with external control, low active |
Synchronization frequency | |
| Common mode operation | ≤ 82 Hz |
| Multiplex operation | ≤ 82 Hz / n , n = number of sensors , n ≤ 10
|
Output |
Output type | 1 push-pull (4 in 1) output, short-circuit protected, reverse polarity protected |
Rated operating current | 100 mA , short-circuit/overload protected |
Voltage drop | ≤ 2.5 V |
Repeat accuracy | ≤ ± 0.1 % of full-scale value |
Switching frequency | factory setting: 12 Hz programmable max. 27 Hz |
Range hysteresis | 1 % of the adjusted operating range (default settings), programmable , min. 1 mm |
Temperature influence | ≤ ± 0.75 % of the end value (with temperature compensation)
from 10 minutes after switching on the sensor ; 0.17 %/K (without temperature compensation) |
Compliance with standards and directives |
Standard conformity | |
| Standards | EN IEC 60947-5-2:2020 IEC 60947-5-2:2019 IEC 61131-9:2013 |
Approvals and certificates |
UL approval | cULus Listed, Class 2 Power Source |
CCC approval | CCC approval / marking not required for products rated ≤36 V |
Ambient conditions |
Ambient temperature | -25 ... 70 °C (-13 ... 158 °F) When fixing with one M18 nut, the temperature range begins with 0 °C (32 °F). |
Storage temperature | -40 ... 85 °C (-40 ... 185 °F) |
Mechanical specifications |
Connection type | Connector plug M8 x 1 , 4-pin |
Degree of protection | IP67 |
Material | |
| Housing | Polycarbonate |
| Transducer | epoxy resin/hollow glass sphere mixture; polyurethane foam |
Installation position | any position |
Mass | 13 g |
Tightening torque, fastening screws | with M3 nuts max. 0.2 Nm with M18 nuts max. 1 Nm |
Dimensions | |
| Height | 31 mm |
| Width | 21 mm |
| Length | 23 mm |
Factory settings |
Output | near switch point: 70 mm far switch point: 800 mm Output mode: Window mode Output logic: normally open |
Beam width | wide |