AS-Interface sensor/actuator module VBA-4E2A-G2-XE/E2
- AS-Interface certificate
- Degree of protection IP67
- A/B node with extended addressing possibility for up to 62 nodes
- Addressing jack
- Flat cable connection with cable piercing technique, variable flat cable guide
- Communication monitoring
- Inputs for 3-wire sensors (PNP) and mechanical contacts
- Power supply of the inputs and outputs from the external auxiliary voltage
- Ground connection (FE) possible
- Function display for bus, ext. auxiliary voltage, inputs and outputs
- Detection of output overload
Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.
Download the complete datasheet as a PDF:
Datasheet excerpt: Technical data of VBA-4E2A-G2-XE/E2
| Product Description |
|---|
| G2 flat module 4 inputs and 2 electronic outputs |
| General specifications | ||
|---|---|---|
| Node type | A/B node | |
| AS-Interface specification | V2.1 | |
| Required gateway specification | ≥ V2.1 | |
| UL File Number | E223772 | |
| Indicators/operating means | ||
| LED FAULT | error display; LED red red: communication error or address is 0 red flashing: overload of outputs |
|
| LED PWR | AS-Interface voltage; LED green | |
| LED AUX | ext. auxiliary voltage UAUX ; LED green | |
| LED IN | switching state (input); 4 LED yellow | |
| LED OUT | Switching state (output); 2 LED yellow | |
| Electrical specifications | ||
| Auxiliary voltage (output) | 20 ... 30 V DC PELV | |
| Rated operating voltage | 26.5 ... 31.6 V from AS-Interface | |
| Rated operating current | ≤ 30 mA | |
| Protection class | III | |
| Current loading capacity | 2 A (IAUX) | |
| Surge protection | UAUX, Uin: Over voltage category III, safe isolated power supplies (PELV) | |
| Input | ||
| Number/Type | 4 inputs for mechanical contacts or 3-wire sensors (PNP), DC | |
| Supply | from external auxiliary voltage UAUX | |
| Input current | 3 mA (typically) | |
| Switching point | according to DIN EN 61131-2 (type 1) | |
| 0 (unattenuated) | ≤ 0.5 mA | |
| 1 (attenuated) | ≥ 2 mA | |
| Signal delay | < 2 ms (input/AS-Interface) | |
| Signal frequency | ≤ 250 Hz | |
| Output | ||
| Number/Type | 2 electronic outputs, PNP, overload and short-circuit proof | |
| Supply | from external auxiliary voltage UAUX | |
| Voltage | ≥ (UAUX - 0.5 V) | |
| Current | 1 A per output , 2 A per module | |
| Usage category | DC-13 | |
| Galvanic isolation | ||
| Input/Output | none | |
| Input/AS-Interface | Basic insulation, rated insulation voltage 120 V DC | |
| Output/AS-Interface | Basic insulation, rated insulation voltage 120 V DC | |
| Directive conformity | ||
| Electromagnetic compatibility | observe notices on the certificate of conformity. | |
| Directive 2014/30/EU | EN 62026-2:2013 | |
| Standard conformity | ||
| Galvanic isolation | EN 60947-1:2007 | |
| Degree of protection | EN 60529:2000 | |
| Mech. capacity | EN 60068-2-6:2008, EN 60068-2-27:1995 | |
| Input | EN 61131-2:2007 | |
| Usage category | EN 60947-5-1:2005 | |
| Emitted interference | EN 61000-6-4:2001 | |
| AS-Interface | EN 62026-2:2013 | |
| Noise immunity | EN 61326-1:2006 | |
| Programming instructions | ||
| Profile | S-7.A.E | |
| IO code | 7 | |
| ID code | A | |
| ID1 code | 7 | |
| ID2 code | E | |
| Data bits (function via AS-Interface) | ||
| D0 | ||
| D1 | ||
| D2 | ||
| D3 | ||
| Parameter bits (programmable via AS-i) | function | |
| P0 | not used | |
| P1 | not used | |
| P2 | not used | |
| P3 | not used | |
| Ambient conditions | ||
| Ambient temperature | -25 ... 60 °C (-13 ... 140 °F) | |
| Storage temperature | -25 ... 85 °C (-13 ... 185 °F) | |
| Relative humidity | 85 % , noncondensing | |
| Climatic conditions | For indoor use only | |
| Altitude | ≤ 2000 m above MSL | |
| Pollution degree | 3 | |
| Mechanical specifications | ||
| Degree of protection | IP67 | |
| Connection | Cable piercing method flat cable yellow/flat cable black inputs/outputs: M12 round connector |
|
| Material | ||
| Housing | PBT | |
| Mass | approx. 100 g | |
| Tightening torque, cable gland | 0.4 Nm | |
| Mounting | Mounting plate | |
Classifications
| System | Classcode |
|---|---|
| ECLASS 13.0 | 27242604 |
| ECLASS 12.0 | 27242604 |
| ECLASS 11.0 | 27242604 |
| ECLASS 10.0.1 | 27242604 |
| ECLASS 9.0 | 27242604 |
| ECLASS 8.0 | 27242604 |
| ECLASS 5.1 | 27242604 |
| ETIM 9.0 | EC001599 |
| ETIM 8.0 | EC001599 |
| ETIM 7.0 | EC001599 |
| ETIM 6.0 | EC001599 |
| ETIM 5.0 | EC001599 |
| UNSPSC 12.1 | 39121535 |
Details: VBA-4E2A-G2-XE/E2
Function
The VBA-4E2A-G2-XE/E2 is an AS-Interface I/O module with 4 inputs and 2 electronic outputs. Mechanical contacts (for example buttons) or 3-wire sensors (PNP) can be connected to the inputs. The outputs are electronic outputs designed for a load of 1 A per output. The sensors and actuators connected to the module input and output must receive power externally through an auxiliary power source.
The IP67 flat module is ideally suited for use in the field. An addressing socket is built into the module.
The connection to the sensors/actuators is made by a M12 x 1 rounded connector. An LED is available on the top of the module to display the current switching state for each channel. There is also an LED for monitoring AS-Interface communication and to display whether the module has 0 as an address. One LED indicates when the AS-Interface voltage is applied, while a second one indicates external power supply.
In the standard configuration, the base (mounting plate) of the U-G3FF is used to connect the yellow AS-Interface flat cable and the black flat cable of the external auxiliary power. This lower section allows for contact with the flat cable from both sides.
It is also possible to feed in the external auxiliary voltage with the M12 x 1 rounded connectors. In this case, the seal included in the base of the U-G3FF should be placed in the cage for the black flat cable to ensure protection type IP67.
The device includes communication monitoring, which switches power off to the outputs if no communication takes place on the AS-Interface line for more than 40 ms.
An output overload is reported by the "periphery error" to the AS-Interface master. Communication over the AS-Interface remains in effect.
Product Documentation: VBA-4E2A-G2-XE/E2
| Brief Instructions | Language | File Type | File Size |
|---|---|---|---|
| Instruction leaflet / Beipackzettel | ALL | 188 KB |
Design / Simulation: VBA-4E2A-G2-XE/E2
| CAD | Language | File Type | File Size |
|---|---|---|---|
| CAD 3-D / CAD 3-D | ALL | STP | 149 KB |
| CAD Portal / CAD Portal | ALL | LINK | --- |
Approvals: VBA-4E2A-G2-XE/E2
| Certificates | Certificate No. | Language | File Type | File Size |
|---|---|---|---|---|
| Canada, USA UL | CoC 20141115-E223772 | ALL | 342 KB | |
| Declaration of Conformity | ||||
| EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F) | DOC-1018C | ALL | 118 KB | |
Associated Products: VBA-4E2A-G2-XE/E2
| Matching System Components | ||||||
|---|---|---|---|---|---|---|
|
||||||
| Accessories | ||||||
|
||||||
|
||||||
This free PDF white paper compares the different TCP-based communication protocols (AMQP, OPC UA, MQTT, REST API) that have found their way up and are considered the enablers of IIoT and Industry 4.0. Get your free download now!
AS-Interface Switch Cabinet Module KE5 – Simple Handling and Improved Manageability
The unique housing design of the new KE5 switch cabinet module enables distinct visibility and simplifies mounting, wiring, and maintenance inside switch cabinets and junction boxes.
Pepperl+Fuchs (Pty) Ltd
8 Glen Eagle Office Park
Koorsboom Ave, Glen Marais, Kempton Park
1619 Johannesburg
South Africa
info@za.pepperl-fuchs.com
+27 87985 0797
Pepperl+Fuchs is a leading developer and manufacturer of electronic sensors and components for the global automation market. Continuous innovation, enduring quality, and steady growth have been the foundation of our success for more than 70 years. Pepperl+Fuchs employs 6,300 people worldwide and has manufacturing facilities in Germany, USA, Singapore, Hungary, Indonesia and Vietnam, most of them ISO 9001 certified.