Serviceline Industrial Sensors
Serviceline Explosion Protection
Redundancy Module PS1000-D2-24.20.RM
- 24 V DC to 28 V DC input
- 2 inputs with 1 output
- Output 24 V DC, 20 A
- Housing width 32 mm
- Built-in decoupling mosfets for 1+1 and N+1 redundancy
- Automatic load sharing
- Reverse input polarity protection
- Easy wiring: distribution terminal for negative pole included
- Redundancy status indicator
- Suitable for Zone 2/Div. 2 mounting
Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.
Ladda ned datablad som PDF::
Utdrag ur datablad: Tekniska data för PS1000-D2-24.20.RM
| Electrical specifications | ||
|---|---|---|
| Voltage drop | input to output 0.1 ... 0.5 V at input 2 x 5 A 0.2 ... 0.5 V at input 2 x 10 A 0.24 ... 0.5 V at input 2 x 12 A load share dependent |
|
| Power dissipation | 1.7 W no load 2.6 ... 4.7 W at input 2 x 5 A 5.6 ... 8.7 W at input 2 x 10 A |
|
| Input | ||
| Rated voltage | 24 ... 28 V | |
| Voltage range | 18 ... 35 V DC | |
| Current | 2 x 12 A at ambient temperature < 45 °C (113 °F) 2 x 10 A at ambient temperature 70 °C (158 °F) 2x 17 mA for max. 5 s for lower output currents see technical information |
|
| Output | ||
| Voltage range | 24 ... 28 V DC | |
| Current | 24 A at ambient temperature < 45 °C (113 °F) 20 A at ambient temperature < 70 °C (158 °F) 32.5 A for max. 5 s max. 26 A in overload or short circuit mode (voltage < 6 V DC) |
|
| Fault indication output | ||
| Connection | terminals 13, 14 : relay contact load share terminals 23, 24 : relay contact redundancy |
|
| Output type | relay contact load share - contact is closed if the adjustment of the output voltages are sufficient - contact is open if an even load share does not occur and readjustment of the output voltage is required relay contact redundancy - contact is closed if no fault is detected - contact is open if one or both input voltages are below 22 V DC or above 30 V DC - contact is open if the output current is higher than the adjusted value of the output current - contact is open if an internal defect of the device is detected |
|
| Contact loading | max. 60 V DC/0.3 A ; 30 V DC/1 A ; 30 V AC/0.5 A resistive load min. 1 mA at 5 V DC |
|
| Galvanic isolation | ||
| Input/Output | SELV/PELV | |
| Indicators/settings | ||
| Display elements | LED green: output status - LED lights up if the output current is smaller than the adjusted value of the output current LEDs green: load share status - LEDs indicate the load share status between the two power supplies LED green: redundancy status - LED lights up if no fault is detected - LED flashes if one ore both input values are below 22 V or above 30 V - LED flashes if the output current is higher than the adjusted value of the output current - LED flashes if an internal defect is detected |
|
| Control elements | rotary switch | |
| Configuration | setting of the output current via rotary switch - switch setting to 5 A in combination with two 5A power supplies (1+1 redundancy) - switch setting to 10 A in combination with two 10A power supplies (1+1 redundancy) - switch setting to 20 A for N+1 redundant systems |
|
| Directive conformity | ||
| Electromagnetic compatibility | ||
| Directive 2014/30/EU | IEC/EN 61000-6-1 , IEC/EN 61000-6-2 , IEC/EN 61000-6-3 , IEC/EN 61000-6-4 | |
| Low voltage | ||
| Directive 2014/35/EU | EN 61010-1 | |
| RoHS | ||
| Directive 2011/65/EU (RoHS) | IEC/EN 63000:2019 | |
| Conformity | ||
| Degree of protection | EN 60529 | |
| Shock resistance | EN 60068-2-27 | |
| Vibration resistance | EN 60068-2-6 | |
| Ambient conditions | ||
| Ambient temperature | -40 ... 70 °C (-40 ... 158 °F) , see technical information | |
| Storage temperature | -40 ... 85 °C (-40 ... 185 °F) | |
| Relative humidity | 5 ... 95 %, noncondensing | |
| Shock resistance | 20 g , 11 ms or 30 g , 6 ms | |
| Vibration resistance | 2 ... 17.8 Hz : ± 1.6 mm , 17.8 ... 500 Hz : 2 g | |
| Mechanical specifications | ||
| Housing material | aluminum alloy , galvanized steel | |
| Degree of protection | IP20 | |
| Connection | ||
| Input/Output | screw terminals conductor cross section: max. 6 mm2 (AWG 20-10) cable diameter: max. 2.8 mm, wire end ferrules included stripped insulation length: 7 mm tightening torque: max. 0.8 Nm |
|
| Relay contact output | spring terminals conductor cross section: max. 1.5 mm2 (AWG 24-16) cable diameter: max. 1.6 mm, wire end ferrules included stripped insulation length: 7 mm |
|
| Mass | approx. 310 g | |
| Dimensions | 32 x 124 x 117 mm (W x H x D) , without DIN mounting rail | |
| Height | 124 mm | |
| Width | 32 mm | |
| Depth | 117 mm | |
| Mounting | on 35 mm DIN mounting rail acc. to EN 60715:2001 | |
| Data for application in connection with hazardous areas | ||
| ATEX approval | ||
| ATEX certificate | EPS 11 ATEX 1 312 X | |
| ATEX marking |  II 3G Ex ec nC II T4 Gc |
|
| Directive conformity | ||
| Directive 2014/34/EU | EN 60079-0:2012+A11:2013 , EN 60079-7:2016 , EN 60079-15:2010 | |
| International approvals | ||
| UL approval | E223176 | |
| IECEx approval | ||
| IECEx certificate | IECEx EPS 20.0057X | |
| IECEx marking | Ex ec nC IIC T4 Gc | |
| Standards | IEC 60079-0:2011 , IEC 60079-7:2015 , IEC 60079-15:2010 | |
| General information | ||
| Supplementary information | Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com. | |
Classifications
| System | Classcode |
|---|---|
| ECLASS 13.0 | 27040790 |
| ECLASS 12.0 | 27040790 |
| ECLASS 11.0 | 27040790 |
| ECLASS 10.0.1 | 27040790 |
| ECLASS 9.0 | 27040790 |
| ECLASS 8.0 | 27049090 |
| ECLASS 5.1 | 27049090 |
| ETIM 9.0 | EC002542 |
| ETIM 8.0 | EC002542 |
| ETIM 7.0 | EC002542 |
| ETIM 6.0 | EC002542 |
| ETIM 5.0 | EC002542 |
| UNSPSC 12.1 | 39121004 |
Details: PS1000-D2-24.20.RM
Informative Literature: PS1000-D2-24.20.RM
| Literature | Language | File Type | File Size |
|---|---|---|---|
| Product Information - PS1000 for Global Use up to Zone 2/Div. 2 | ENG | 577 KB |
Product Documentation: PS1000-D2-24.20.RM
| Product information | Language | File Type | File Size |
|---|---|---|---|
| Technical information | ENG | 3796 KB | |
| Safety and Security Documentation | |||
| Instruction manual / Betriebsanleitung | ALL | 225 KB | |
| Instruction manual / Betriebsanleitung | ALL | 294 KB | |
Design / Simulation: PS1000-D2-24.20.RM
| CAD | Language | File Type | File Size |
|---|---|---|---|
| CAD 3-D / CAD 3-D | ALL | STP | 4884 KB |
| CAD Portal / CAD Portal | ALL | LINK | --- |
| CAE | |||
| CAE EPLAN macro EDZ / CAE EPLAN Makro EDZ | ALL | EDZ | 200 KB |
Approvals: PS1000-D2-24.20.RM
| Certificates | Cert No. | Language | File Type | File Size |
|---|---|---|---|---|
| Bureau Veritas IECEx Certificate of Conformity | IECEx EPS 20.0057X | ALL | LINK | --- |
| Canada, USA CSA Hazardous Location | CoC 80059967 | ALL | 84 KB | |
| China SITIIAS CCC Ex Certificate | 2023122303116293 (Mannheim) | ALL | 519 KB | |
| Europe Bureau Veritas ATEX Category 3 G | EPS 11 ATEX 1 312X | ALL | 1011 KB | |
| US CA UL | CoC E223176 RptRef E223176-20070416 | ALL | 444 KB | |
| Declaration of Conformity | ||||
| EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F) | DOC-4793 | ALL | 73 KB | |
| EU Declaration of Conformity (P+F) | TDOC-4793ASWE | SWE | 183 KB | |
Associated Products: PS1000-D2-24.20.RM
| Accessory of | ||||||
|---|---|---|---|---|---|---|
|
||||||
|
||||||
Pepperl+Fuchs AB
Bultgatan 40 A
442 40 Kungälv
Sverige
orgnr. 556212-2126
info@se.pepperl-fuchs.com
+46 303 246070
© 2024 All Rights Reserved.
Pepperl+Fuchs is a leading developer and manufacturer of electronic sensors and components for the global automation market. Continuous innovation, enduring quality, and steady growth have been the foundation of our success for more than 70 years. Pepperl+Fuchs employs 6,300 people worldwide and has manufacturing facilities in Germany, USA, Singapore, Hungary, Indonesia and Vietnam, most of them ISO 9001 certified.