SMART Transmitter Power Supply/Current Driver HiD2024

4-channel isolated barrier
24 V DC supply (bus powered)
Analog in or analog out signals
Sink and source mode outputs
SMART pass-through
Up to SIL 2 acc. to IEC/EN 61508

Technical Data
Product Documentation
Design / Simulation
Approvals

Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.

Ladda ned datablad som PDF::

Utdrag ur datablad: Tekniska data för HiD2024

General specifications
Signal type		Analog input/analog output
Functional safety related parameters
Safety Integrity Level (SIL)		SIL 2
Supply
Connection		SL1: 1a(-), 1b(-); 2a(+), 2b(+)
Rated voltage		20.4 ... 30 V DC bus powered via Termination Board
Ripple		≤ 10 %
Rated current		140 mA at 24 V and 20 mA
Power dissipation		≤ 1.8 W at 20 mA
Power consumption		≤ 3.3 W at 20 mA
Control circuit
Connection		SL1: 8a(+), 7a(-); 10a(+), 9a(-); 9b(+), 10b(-); 8b(+), 7b(-)
Voltage drop		approx. 6 V or internal resistance 300 Ω at 20 mA
Ripple		200 mV _eff
Input
	Signal	4 ... 20 mA
	Resistor	> 100 kΩ at max. 23 V, with field wiring open
Output
	Signal	4 ... 20 mA or 1 ... 5 V (on 250 Ω, 0.1 % internal shunt) 4 ... 20 mA (sink mode), operating voltage 15 ... 26 V
	Load	0 ... 300 Ω (source mode)
Field circuit
Connection		SL2: 5a(+), 5b(-); 1a(+), 1b(-); 3a(+), 3b(-); 7a(+), 7b(-)
Voltage		≥ 15 V at 20 mA
Input
	Signal	4 ... 20 mA , limited to approx. 30 mA
Output
	Signal	4 ... 20 mA
	Load	0 ... 650 Ω
Transfer characteristics
Deviation		at 20 °C (68 °F) ≤ ± 0.1 % incl. non-linearity and hysteresis (source mode 4 ... 20 mA) ≤ ± 0.2 % incl. non-linearity and hysteresis (sink mode 4 ... 20 mA) ≤ ± 0.2 % incl. non-linearity and hysteresis (source mode 1 ... 5 V) ≤ ± 0.2 % incl. non-linearity and hysteresis (analog output mode 4 ... 20 mA)
	Influence of ambient temperature	< 2 µA/K (0 ... 60 °C (32 ... 140 °F)); < 4 µA/K (-20 ... 0 °C (-4 ... 32 °F))
Frequency range		field side into the control side: bandwidth with 0.5 V_pp signal 0 ... 3 kHz (-3 dB) control side into the field side: bandwidth with 0.5 V_pp signal 0 ... 3 kHz (-3 dB)
Rise time		10 to 90 % ≤ 20 ms
Galvanic isolation
Output/power supply		basic insulation according to IEC 62103, rated insulation voltage 50 V_eff
Indicators/settings
Display elements		LED
Control elements		DIP switch potentiometer
Factory setting		analog input with source output
Configuration		via DIP switches via potentiometer
Labeling		space for labeling at the front
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2013 (industrial locations)
Conformity
Electromagnetic compatibility		NE 21:2006 For further information see system description.
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Mechanical specifications
Degree of protection		IP20
Mass		approx. 140 g
Dimensions		18 x 114 x 130 mm (0.7 x 4.5 x 5.1 inch) (W x H x D)
	Height	114 mm
	Width	18 mm
	Depth	130 mm
Mounting		on termination board
Coding		pin 1 and 3 trimmed For further information see system description.
Data for application in connection with hazardous areas
EU-type examination certificate		CESI 02 ATEX 086
	Marking	II (1)G [Ex ia Ga] IIC , II (1)D [Ex ia Da] IIIC
	Input	Ex ia, Ex iaD
Supply
	Maximum safe voltage	250 V AC (Attention! U_m is no rated voltage.)
Equipment
	Voltage	25.2 V
	Current	93 mA
	Power	586 mW
	Internal capacitance	1.2 nF
	Internal inductance	negligible
Certificate		PF 11 CERT 2109 X
	Marking	II 3G Ex nA IIC T4 Gc
Galvanic isolation
	Input/Output	safe electrical isolation acc. to EN 60079-11: 2007, voltage peak value 375 V
	Input/power supply	safe electrical isolation acc. to EN 60079-11: 2007, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2012+A11:2013 , EN 60079-11:2012 , EN 60079-15:2010
International approvals
IECEx approval
	IECEx certificate	IECEx TUN 04.0012
	IECEx marking	[Ex ia] IIC
General information
Supplementary information		Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.

Classifications

System	Classcode
ECLASS 13.0	27210119
ECLASS 12.0	27210119
ECLASS 11.0	27210119
ECLASS 10.0.1	27210119
ECLASS 9.0	27210119
ECLASS 8.0	27210119
ECLASS 5.1	27210119
ETIM 9.0	EC001485
ETIM 8.0	EC001485
ETIM 7.0	EC001485
ETIM 6.0	EC001485
ETIM 5.0	EC001485
UNSPSC 12.1	32101514

Details: HiD2024

Product Documentation: HiD2024

Safety and Security Documentation	Language	File Type	File Size
Manual	SWE	PDF	160 KB
Functional Safety Manual	ENG	PDF	518 KB
Manuals
System Manual	ENG	PDF	5438 KB

Design / Simulation: HiD2024

CAD	Language	File Type	File Size
CAD 2-D / CAD 2-D	ALL	ZIP	16364 KB
CAE
EPLAN macros H-System devices (EMA) / EPLAN-Makros Geräte H-System (EMA)	ALL	ZIP	3536 KB

Approvals: HiD2024

Certificates	Cert No.	Language	File Type	File Size
Europe CESI ATEX Category (1) D ATEX Category (1) G	CESI 02 ATEX 086	ALL	PDF	3887 KB
Europe Pepperl+Fuchs ATEX Category 3 G	PF 11 CERT 2109 X	ALL	PDF	446 KB
TUV Nord IECEx Certificate of Conformity	IECEx TUN 04.0012	ALL	LINK	---
Declaration of Conformity
EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F)	DOC-0905B	ALL	PDF	48 KB

Allmänna kommentarer om produktinformationen från Pepperl+Fuchs

Länkar

Selector for Safety Products

Choose from various selection criteria like safety integrity level, performance level, device function, and signal type and find the SIL/PL assessed device that you are looking for.

Pepperl+Fuchs AB
Bultgatan 40 A
442 40 Kungälv
Sverige
orgnr. 556212-2126
info@se.pepperl-fuchs.com
phone +46 303 246070

Pepperl+Fuchs is a leading developer and manufacturer of electronic sensors and components for the global automation market. Continuous innovation, enduring quality, and steady growth have been the foundation of our success for more than 70 years. Pepperl+Fuchs employs 6,300 people worldwide and has manufacturing facilities in Germany, USA, Singapore, Hungary, Indonesia and Vietnam, most of them ISO 9001 certified.