Digital Input LB1009A

8-channel
Inputs Ex ic
Installation in Zone 2 or safe area
Dry contact or NAMUR inputs
Positive or negative logic selectable
Simulation mode for service operations (forcing)
Line fault detection (LFD)
Permanently self-monitoring
Module can be exchanged under voltage

Technical Data
Informative Literature
Product Documentation
Design / Simulation
Approvals
Tilhørende produkter

Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.

Hent hele databladet som PDF:

Uddrag af datablad: Tekniske data for LB1009A

Produkt beskrivelse
Digital Input

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power dissipation		1.55 W
Power consumption		1.55 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Digital input
Number of channels		8
Sensor interface
	Connection	NAMUR sensor
	Connection [2]	volt-free contact
	Connection [3]	Usage without connection to areas where there is a risk of explosion: active signals, mechanical contacts, NAMUR sensors, 2-wire sensors If the device has been operated in general electrical systems that are not connected to areas where there is a risk of explosion, the device cannot then be used in electrical systems that are connected to areas where there is a risk of explosion. Usage with connection to areas where there is a risk of explosion: mechanical contacts, NAMUR sensors
Connection		Terminals 1+, 2-, 3+, 4-, 5+, 6-, 7+, 8-, 9+, 10-, 11+, 12-, 13+,14-, 15+, 16-
Rated values		acc. to EN 60947-5-6 (NAMUR)
Switching point/switching hysteresis		1.2 ... 2.1 mA / ± 0.2 mA
Voltage		8.2 V
Internal resistor		1 kΩ
Line fault detection		can be switched on/off for each channel via configuration tool , active signals (24 V, 5 V) without line fault detection
	Connection	mechanical switch with additional resistors (see connection diagram) proximity sensors without additional wiring
	Short-circuit	< 360 Ω
	Open-circuit	< 0.35 mA
Digital signals (active)		Use in safe area: configurable 24 V 5 V
	Switching point: ON	> 8 V > 2.7 V
	Switching point: OFF	< 3 V < 2.3 V
Minimum pulse duration		15 ms
Indicators/settings
LED indication		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1-8) red: line fault (lead breakage or short circuit) , yellow: signal (per channel)
Coding		optional mechanical coding via front socket
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2013
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Environmental test		EN 60068-2-14
Shock resistance		EN 60068-2-27
Vibration resistance		EN 60068-2-6
Damaging gas		EN 60068-2-42
Relative humidity		EN 60068-2-78
Ambient conditions
Ambient temperature		-40 ... 60 °C (-40 ... 140 °F) , 70 °C (non-Ex)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Relative humidity		95 % non-condensing
Altitude		max. 2000 m
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz; transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g; 10 cycles frequency range 5 ... 100 Hz; transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g; 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with spring terminal (0.14 ... 0.5 mm²)
Mass		approx. 90 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
Input
	Voltage	10 V
	Current	12 mA
	Power	30 mW (linear characteristic)
Certificate		EXA 13 ATEX 0037X
	Marking	II 3 G Ex nA [ic] IIC T4 Gc
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN IEC 60079-0:2018+AC:2020 EN 60079-11:2012 EN 60079-15:2010
International approvals
ATEX approval		EXA 13 ATEX 0037X
IECEx approval
	IECEx certificate	IECEx EXA 13.0003X
	IECEx marking	Ex nA [ic] IIC T4 Gc
General information
System information		The module has to be mounted in appropriate backplanes (LB9***) in Zone 2 or outside hazardous areas. Here, observe the corresponding declaration of conformity. For use in hazardous areas (e. g. Zone 2 or Zone 22) the module must be installed in an appropriate enclosure.
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.

Classifications

System	Classcode
ECLASS 13.0	27210121
ECLASS 12.0	27210121
ECLASS 11.0	27210121
ECLASS 10.0.1	27210121
ECLASS 9.0	27210121
ECLASS 8.0	27210121
ECLASS 5.1	27210120
ETIM 9.0	EC001485
ETIM 8.0	EC001485
ETIM 7.0	EC001485
ETIM 6.0	EC001485
ETIM 5.0	EC001485
UNSPSC 12.1	39121008

Details: LB1009A

Informative Literature: LB1009A

Literature	Sprog	Fil type	Fil størrelse
Application Report - Communication Redundancy for Uninterrupted Operation	ENG	PDF	529 KB
Application Report - LB and FB Remote I/O Systems for Digitally Connecting Analog Field Devices	ENG	PDF	208 KB
Application Report - Space Saving Extension for Existing Plants	ENG	PDF	300 KB
Application Report - The Modern Whiskey Distillery	ENG	PDF	176 KB
Application Report - Use of Remote I/O in Fluidized Bed Systems	ENG	PDF	222 KB
Application Report - Using Remote I/O Systems for the Efficient Digitalization of Plants	ENG	PDF	371 KB

Product Documentation: LB1009A

Safety and Security Documentation	Sprog	Fil type	Fil størrelse
Instruktions manual	DAN	PDF	171 KB
Manuals
Hardware Manual LB-Remote-I/O-System	ENG	PDF	5385 KB

Design / Simulation: LB1009A

CAD	Sprog	Fil type	Fil størrelse
CAD 3-D / CAD 3-D	ALL	STP	3018 KB

Approvals: LB1009A

Certificates	Certifikat nr.	Sprog	Fil type	Fil størrelse
Brasil TUV Rheinland Brazil	TÜV 14.1600 X	ALL	PDF	1224 KB
Bureau Veritas (Maritime) Marine	22449/C0 BV	ALL	PDF	590 KB
China SITIIAS CCC Ex Certificate	2020322310002776 (Singapore)	ALL	PDF	1374 KB
EXA IECEx Certificate of Conformity Non-Sparking nA	IECEx EXA 13.0003X	ALL	LINK	---
Europe ATEX Category 3 G	EXA 13 ATEX 0037X	ALL	PDF	2198 KB
Lloyd's Register Marine	LR2003616TA-02	ALL	PDF	557 KB
South Africa MASC	MASC MS/20-8433X	ALL	PDF	756 KB
South Africa MASC	MASC MS/20-8438X	ALL	PDF	730 KB
Declaration of Conformity
EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F)	DOC-0372C	ALL	PDF	1141 KB
UK Declaration of Conformity (P+F) / UK-Konformitäterklärung (P+F)	DOC-5375	ALL	PDF	1137 KB

Tilhørende produkter: LB1009A

Accessories

	LB9131A Terminal Block
	Spring terminal, For LB modules, 8-pole, Color green, For non-intrinsically safe or Ex ic applications, For wire end ferrules without plastic sleeve only, Construction type: spring terminalpa

Generelle bemærkninger vedr. produktoplysninger fra Pepperl+Fuchs

Hurtige links

The Gateway to Industry 4.0

The new LB/FB PROFINET gateways from Pepperl+Fuchs open the door for IIoT 4.0 applications in process industries.

Pepperl+Fuchs A/S
Kirkebjerg Allé 90
DK-2605 Brøndby
Denmark
info@dk.pepperl-fuchs.com
phone +45 7010 4210

Pepperl+Fuchs er markedsledende indenfor udvikling og fabrikation af elektroniske sensorer og komponenter til det globale automatiseringsmarked. Kontinuerlig innovation, kombineret med høj kvalitet og stabil vækst har sikret uafbrudt succes gennem mere end 70 år. Pepperl+Fuchs har 6.300 ansatte på verdensplan og har produktionsfaciliteter i Tyskland, USA, Singapore, Ungarn, Indonesien og Vietnam; de fleste ISO 9001 certificerede.