Support Industrielle sensorer
Support Explosion Protection
Double sheet sensor UDC-18GS-3EP1-IO-0,2M-V19
- Ultrasonic system for reliable detection of no, one, or two overlapping sheet materials
- Insensitive to printing, colors, and shining surfaces
- Very wide material spectrum, finest papers up to thin sheet metals as well as plastic- and metal foils
- Perpendicular or inclined sensor mounting relative to the sheet plane possible
- Integrated alignment aid
- IO-Link Interface for process data, parameterization and diagnosis
- Synchronization options
- No teach-in required
- Short version
Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.
Hent hele databladet som PDF:
Uddrag af datablad: Tekniske data for UDC-18GS-3EP1-IO-0,2M-V19
| General specifications | ||
|---|---|---|
| Sensing range | 20 ... 60 mm , optimal distance: 45 mm | |
| Transducer frequency | approx. 255 kHz | |
| Memory | ||
| Non-volatile memory | EEPROM | |
| Write cycles | 300000 | |
| Indicators/operating means | ||
| LED green | indication: single sheet detected flashing (1 Hz) - standby mode flashing with short break (1 Hz) - IO-Link mode |
|
| LED yellow | indication: no sheet detected (Air) | |
| LED red | indication: double sheet detected flashing: device error |
|
| Electrical specifications | ||
| Operating voltage | 18 ... 30 V DC , ripple 10 %SS | |
| No-load supply current | ≤ 40 mA | |
| Power consumption | ≤ 550 mW | |
| Time delay before availability | ≤ 300 ms | |
| Interface | ||
| Interface type | IO-Link | |
| IO-Link revision | 1.1 | |
| Device profile | Identification and Diagnosis - I&D | |
| Process data | Input: 16 Bit - measurement value 8 Bit - selected threshold set 2 Bit - switching signals 3 Bit Output: 8 Bit - threshold set 2 Bit - disable transducer 1 Bit |
|
| Vendor ID | 1 (0x0001) | |
| Device ID | 3148290 (0x300A02) | |
| Transfer rate | COM2 (38.4 kBit/s) | |
| Min. cycle time | 2.8 ms | |
| SIO mode support | yes | |
| Compatible master port type | Class A (use adapter cable listed in accesories) Class B (use 3-pole adapter or 3-wire cable) |
|
| Input/Output 1 | ||
| Designation | SYNC | |
| Input/output type | 1 synchronization connection, bidirectional | |
| 0 Level | 0 ... 1 V | |
| 1 Level | 2.5 V ... UB | |
| Input impedance | > 22 kΩ | |
| Output rated operating current | current source < 2.5 mA | |
| Pulse length | 0.4 ... 3 ms with external control, low active | |
| Synchronization frequency | ||
| Common mode operation | ≤ 230 Hz | |
| Multiplex operation | ≤ 230 Hz /n, n = number of sensors , n ≤ 10 | |
| Input/Output 2 | ||
| Designation | IN2/FEEDBACK | |
| Input/output type | input or output programmable via IO-Link : input for selection of a threshold set (factory default) output as feedback output |
|
| Input type | digital input | |
| Signal | 0-level: 0 ... + 1V 1-level: +UB - 1 V ... +UB |
|
| Input impedance | ≥ 60 kΩ | |
| Pulse length | ≥ 100 ms | |
| Output type | PNP | |
| Rated operating current | 8 mA | |
| Voltage drop | < 3 V | |
| Fusing | reverse polarity protected , overload and short-circuit protected | |
| Input | ||
| Designation | IN1/TEACH | |
| Input type | 0-level: 0 ... + 1V 1-level: +UB - 1 V ... +UB |
|
| Pulse length | ≥ 100 ms | |
| Impedance | ≥ 60 kΩ | |
| Output | ||
| Designation | OUT 1 ... 3 | |
| Number | 3 | |
| Output function | OUT 1: single sheet detected OUT 2: double sheet detected OUT 3: no sheet detected (air) |
|
| Output type | Push-pull (4 in 1) output , NC contact ( programmable ) | |
| Rated operating current | 100 mA per output | |
| Voltage drop | ≤ 3 V | |
| Switch-on delay | 15 ms (programmable) | |
| Switch-off delay | 15 ms (programmable) | |
| Pulse extension | can be activated (100 ms or IO-Link cycle time) | |
| Fusing | reverse polarity protected , overload and short-circuit resistant | |
| Compliance with standards and directives | ||
| Standard conformity | ||
| Standards | EN IEC 60947-5-2:2020 IEC 60947-5-2:2019 IEC 61131-9 / IO-Link V1.1.3 |
|
| Approvals and certificates | ||
| UL approval | cULus Listed, General Purpose, Class 2 Power Source | |
| CCC approval | CCC approval / marking not required for products rated ≤36 V | |
| Ambient conditions | ||
| Ambient temperature | 0 ... 60 °C (32 ... 140 °F) | |
| Storage temperature | -25 ... 70 °C (-13 ... 158 °F) | |
| Mechanical specifications | ||
| Connection type | fixed cable with plug | |
| Housing length | ||
| Ultrasonic transmitter | 21 mm | |
| Ultrasonic receiver | 52 mm | |
| Housing diameter | ||
| Ultrasonic transmitter | 18 mm | |
| Ultrasonic receiver | 18 mm | |
| Degree of protection | IP65 | |
| Material | ||
| Housing | Stainless steel 1.4305/AISI 303, polyamide plastic parts | |
| Transducer | epoxy resin/hollow glass sphere mixture; polyurethane foam | |
| Connector | ||
| Threading | M12 x 1 | |
| Number of pins | 8 | |
| Cable | ||
| Cable diameter | 4.3 mm | |
| Bending radius | 5 x diameter , fixed installation | |
| Material | PUR | |
| Color | black | |
| Length | approx. 200 mm | |
| Mass | 75 g | |
| Tightening torque, fastening screws | max. 20 Nm | |
Classifications
| System | Classcode |
|---|---|
| ECLASS 13.0 | 27272801 |
| ECLASS 12.0 | 27272801 |
| ECLASS 11.0 | 27272801 |
| ECLASS 10.0.1 | 27272801 |
| ECLASS 9.0 | 27272801 |
| ECLASS 8.0 | 27272801 |
| ECLASS 5.1 | 27272801 |
| ETIM 9.0 | EC001847 |
| ETIM 8.0 | EC001847 |
| ETIM 7.0 | EC001847 |
| ETIM 6.0 | EC001847 |
| ETIM 5.0 | EC001847 |
| UNSPSC 12.1 | 41111960 |
Details: UDC-18GS-3EP1-IO-0,2M-V19
Informative Literature: UDC-18GS-3EP1-IO-0,2M-V19
| Literature | Sprog | Fil type | Fil størrelse |
|---|---|---|---|
| Application Report - Reliable Detecting Foil Tears in Battery Cell Manufacturing | ENG | 163 KB |
Product Documentation: UDC-18GS-3EP1-IO-0,2M-V19
| Brief Instructions | Sprog | Fil type | Fil størrelse |
|---|---|---|---|
| Commissioning instruction for series UDC-18GS-* / Inbetriebnahmeanleitung für Serie UDC-18GS-* | ALL | 379 KB | |
| Safety and Security Documentation | |||
| Instruktions manual | DAN | 146 KB | |
| Manuals | |||
| Manual UDC-/UDCM-*GS-*-IO*-Series Parameterization of Ultrasonic Double Sheet Sensors with IO-Link Interface | ENG | 4602 KB | |
| Parameter Information | |||
| IO-Link Parameter-Datasheet UDC-18GS-3EP1-IO-0,2M-V19 | ENG | 584 KB | |
Design / Simulation: UDC-18GS-3EP1-IO-0,2M-V19
| CAD | Sprog | Fil type | Fil størrelse |
|---|---|---|---|
| CAD 3-D / CAD 3-D | ALL | STP | 6865 KB |
| CAD Portal / CAD Portal | ALL | LINK | --- |
| CAE | |||
| CAE EPLAN Data Portal / CAE EPLAN Data Portal | ALL | LINK | --- |
| CAE EPLAN macro EDZ / CAE EPLAN Makro EDZ | ALL | EDZ | 75 KB |
Approvals: UDC-18GS-3EP1-IO-0,2M-V19
| Certificates | Certifikat nr. | Sprog | Fil type | Fil størrelse |
|---|---|---|---|---|
| Canada USA UL Ordinary Location | UL-US-2140156-4 / UL-CA-2133660-4 | ALL | 284 KB | |
| IO-Link Manufacturer Declaration | CERT-6559A | ALL | 295 KB | |
| Declaration of Conformity | ||||
| EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F) | DOC-5827 | ALL | 34 KB | |
| UK Declaration of Conformity (P+F) / UK-Konformitäterklärung (P+F) | DOC-5828 | ALL | 32 KB | |
Software: UDC-18GS-3EP1-IO-0,2M-V19
| Device Description Files/Drivers | Udgivelses info | Fil type | Fil størrelse |
|---|---|---|---|
| IODD for UDC-18GS-3EP1 / IODD für UDC-18GS-3EP1 | V1.00.000 / 2022-03-30 | ZIP | 300 KB |
| DTM (Device Type Manager) Package for UDC-18GS*/UDC-30GS* ultrasonic sensors / DTM (Device Type Manager) Package für UDC-18GS*/UDC-30GS* Ultraschallsensoren | V1.1.0.0 / 08-08-2022 | ZIP | 16847 KB |
| Software Tools | |||
| IO-Link Offline Parameterization Tool / IO-Link Offline-Parametriertool | V1.00.006 / 2022-07-10 | ZIP | 96138 KB |
Tilhørende produkter: UDC-18GS-3EP1-IO-0,2M-V19
| Accessories | ||||||
|---|---|---|---|---|---|---|
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
Pepperl+Fuchs offers you various downloadable documents containing knowledge on ultrasonic sensors.
Pepperl+Fuchs A/S
Kirkebjerg Allé 90
DK-2605 Brøndby
Denmark
info@dk.pepperl-fuchs.com
+45 7010 4210
© 2024 Alle rettigheder forbeholdt.
Pepperl+Fuchs er markedsledende indenfor udvikling og fabrikation af elektroniske sensorer og komponenter til det globale automatiseringsmarked. Kontinuerlig innovation, kombineret med høj kvalitet og stabil vækst har sikret uafbrudt succes gennem mere end 70 år. Pepperl+Fuchs har 6.300 ansatte på verdensplan og har produktionsfaciliteter i Tyskland, USA, Singapore, Ungarn, Indonesien og Vietnam; de fleste ISO 9001 certificerede.