Support Industrielle sensorer
Support Explosion Protection
SMART Transmitter Power Supply HiD2030SK
- 2-channel isolated barrier
- 24 V DC supply (bus powered)
- 2-wire SMART transmitters or current sources
- Usable as signal splitter (1 input and 2 outputs)
- Dual output 4 mA ... 20 mA, current sink
- Line fault detection (LFD)
- Up to SIL 2 (SC 3) acc. to IEC/EN 61508
Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.
Hent hele databladet som PDF:
Uddrag af datablad: Tekniske data for HiD2030SK
| General specifications | ||
|---|---|---|
| Signal type | Analog input | |
| Functional safety related parameters | ||
| Safety Integrity Level (SIL) | SIL 2 | |
| Systematic capability (SC) | SC 3 | |
| Supply | ||
| Connection | SL1: 1a(-), 1b(-); 2a(+), 2b(+) | |
| Rated voltage | 19 ... 30 V DC bus powered via Termination Board | |
| Rated current | 14 mA at 24 V, 250 Ω load, 20 mA output (per channel) | |
| Power dissipation | 350 mW at 24 V, 250 Ω load, 20 mA output (per channel) | |
| Input | ||
| Connection side | field side | |
| Connection | SL2: 5a(+), 5b, 7a(-); 1a(+), 1b, 3b(-) | |
| Input current | 4 ... 20 mA , current limit approx. 26 mA typ. | |
| Input resistance | < 40 Ω , for current source | |
| Ripple | 10 mV eff | |
| Voltage | min. 15.5 V at 20 mA | |
| Communication | pass-through of HART signal to safe area The current sink terminals 4, 7 and 5, 6 do not pass HART signal to safe area. |
|
| Output | ||
| Connection side | control side | |
| Connection | SL1: 8a(+), 7a(-); 10a(+), 9a(-) | |
| Output | sink mode from external supply | |
| Output signal | 4 ... 20 mA | |
| Voltage | working voltage 7 ... 30 V | |
| Response time | 70 ms , 10 ... 90 % step change | |
| Signal level | no fault: 1 mA ... 23.5 mA input current fault detection: < 0.2 mA or > 24 mA input current |
|
| Fault indication output | ||
| Connection | SL1: 6b | |
| Output type | open collector transistor (common to both channels) fault bus signal, collective error message |
|
| Transfer characteristics | ||
| Deviation | at 20 °C (68 °F), 0/4 ... 20 mA ≤ 20 µA incl. calibration, linearity, hysteresis, loads and fluctuations of supply voltage |
|
| Influence of ambient temperature | ≤ 2 µA/K | |
| Frequency range | field side into the control side: bandwidth with 0.5 Vpp signal 0 ... 3 kHz (-3 dB) control side into the field side: bandwidth with 0.5 Vpp signal 0 ... 3 kHz (-3 dB) |
|
| Galvanic isolation | ||
| Input/Output | basic insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff | |
| Input/power supply | reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff | |
| Output/power supply | basic insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff | |
| Output/Output | functional insulation, rated insulation voltage 50 V AC | |
| Indicators/settings | ||
| Display elements | LEDs | |
| Labeling | space for labeling at the front | |
| Directive conformity | ||
| Electromagnetic compatibility | ||
| Directive 2014/30/EU | EN 61326-1:2013 (industrial locations) | |
| Conformity | ||
| Electromagnetic compatibility | NE 21:2017 EN 61326-3-2:2018 |
|
| Degree of protection | IEC 60529:2001 | |
| Protection against electrical shock | UL 61010-1:2012 | |
| Ambient conditions | ||
| Ambient temperature | -40 ... 60 °C (-40 ... 140 °F) | |
| Relative humidity | 5 ... 90 %, non-condensing up to 35 °C (95 °F) | |
| Mechanical specifications | ||
| Degree of protection | IP20 | |
| Mass | 140 g | |
| Dimensions | 18 x 114 x 130 mm (0.7 x 4.5 x 5.1 inch) (W x H x D) | |
| Height | 114 mm | |
| Width | 18 mm | |
| Depth | 130 mm | |
| Mounting | on termination board | |
| Coding | pin 1 and 3 trimmed For further information see system description. |
|
| Data for application in connection with hazardous areas | ||
| EU-type examination certificate | CSANe 21 ATEX 2149 X | |
| Marking |  II (1)G [Ex ia Ga] IIC II (1)D [Ex ia Da] IIIC I (M1) [Ex ia Ma] I |
|
| Input | Ex ia, Ex iaD | |
| Voltage | 26 V | |
| Current | 93 mA | |
| Power | 605 mW | |
| Supply | ||
| Maximum safe voltage | 250 V AC (Attention! Um is no rated voltage.) | |
| Galvanic isolation | ||
| Input/input | safe electrical isolation acc. to EN 60079-11:2007, voltage peak value 60 V | |
| Input/Output | safe electrical isolation acc. to IEC 60079-11:2007, voltage peak value 375 V | |
| Input/power supply | safe electrical isolation acc. to IEC 60079-11:2007, voltage peak value 375 V | |
| Directive conformity | ||
| Directive 2014/34/EU | EN 60079-0:2018 , EN 60079-11:2012 | |
| International approvals | ||
| CSA approval | CoC 80072560 (cCSAus) | |
| Control drawing | 116-0486 | |
| IECEx approval | ||
| IECEx certificate | IECEx CSAE 21.0010X | |
| IECEx marking | [Ex ia Ga] IIC , [Ex ia Da] IIIC , [Ex ia Ma] I | |
| General information | ||
| Supplementary information | Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com. | |
Classifications
| System | Classcode |
|---|---|
| ECLASS 13.0 | 27210119 |
| ECLASS 12.0 | 27210119 |
| ECLASS 11.0 | 27210119 |
| ECLASS 10.0.1 | 27210119 |
| ECLASS 9.0 | 27210119 |
| ECLASS 8.0 | 27210119 |
| ECLASS 5.1 | 27210119 |
| ETIM 9.0 | EC001485 |
| ETIM 8.0 | EC001485 |
| ETIM 7.0 | EC001485 |
| ETIM 6.0 | EC001485 |
| ETIM 5.0 | EC001485 |
| UNSPSC 12.1 | 32101514 |
Details: HiD2030SK
Product Documentation: HiD2030SK
| Safety and Security Documentation | Sprog | Fil type | Fil størrelse |
|---|---|---|---|
| Instruktions manual | DAN | 137 KB | |
| Functional Safety Manual | ENG | 1979 KB | |
| Manuals | |||
| System Manual | ENG | 5438 KB | |
Design / Simulation: HiD2030SK
| CAD | Sprog | Fil type | Fil størrelse |
|---|---|---|---|
| CAD 2-D / CAD 2-D | ALL | ZIP | 16364 KB |
Approvals: HiD2030SK
| Certificates | Certifikat nr. | Sprog | Fil type | Fil størrelse |
|---|---|---|---|---|
| CSA IECEx Certificate of Conformity | IECEx CSAE 21.0010X | ALL | LINK | --- |
| Canada USA CSA Certificate of Compliance | CoC 80072560 cCSAus | ALL | 123 KB | |
| Europe CSA ATEX Category (1) D ATEX Category (M1) ATEX Category (1) G | CSANe 21 ATEX 2149X | ALL | 415 KB | |
| Worldwide TUV Rheinland Functional Safety Certificate | No.: 968/FSP 2300.00/21 | ALL | 619 KB | |
| Control Drawings | ||||
| Control drawing CSA / Control drawing CSA | ALL | 137 KB | ||
| Declaration of Conformity | ||||
| EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F) | DOC-5409A | ALL | 469 KB | |
Choose from various selection criteria like safety integrity level, performance level, device function, and signal type and find the SIL/PL assessed device that you are looking for.
Pepperl+Fuchs A/S
Kirkebjerg Allé 90
DK-2605 Brøndby
Denmark
info@dk.pepperl-fuchs.com
+45 7010 4210
© 2024 Alle rettigheder forbeholdt.
Pepperl+Fuchs er markedsledende indenfor udvikling og fabrikation af elektroniske sensorer og komponenter til det globale automatiseringsmarked. Kontinuerlig innovation, kombineret med høj kvalitet og stabil vækst har sikret uafbrudt succes gennem mere end 70 år. Pepperl+Fuchs har 6.300 ansatte på verdensplan og har produktionsfaciliteter i Tyskland, USA, Singapore, Ungarn, Indonesien og Vietnam; de fleste ISO 9001 certificerede.