NBN50-F135L-M18-1M-SET Inductive Sensor Kit

Key Benefits at a Glance

The technical data only apply when an inductive sensor head is connected
Extremely wide temperature range of the inductive sensor head
0 ... 250 °C (0 ... 482 °F)
IO-Link Interface for process data, parameterization and diagnosis
Replacement of the sensor heads
Identical amplifier for different cable lengths
Direct baying of the sensor heads through synchronization

Product photo: Inductive Sensor Kit NBN50-F135L-M18-1M-SET

Dimensions: Inductive Sensor Kit NBN50-F135L-M18-1M-SET

Connection Assignment: Inductive Sensor Kit NBN50-F135L-M18-1M-SET

Note

All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.

Datasheet Function Classification Informative Literature Product Documentation Design / Simulation Approvals Software

Technical data of NBN50-F135L-M18-1M-SET

Modular inductive sensor for high-temperature applications with rated operating distance 50 mm, with IO-Link interface, consisting of separable inductive sensor head with 1 m cable and amplifier

Switching function		Normally open/closed (NO/NC) programmable
Output type		PNP
Rated operating distance	s_n	50 mm
Installation		flush mountable
Output polarity		DC
Assured operating distance	s_a	0 ... 40.5 mm
Actuating element		Steel Fe360 , 150 mm x 150 mm x 1 mm
Reduction factor r_Al		0.6
Reduction factor r_Cu		0.5
Reduction factor r₃₀₄		1
Reduction factor r_Brass		0.9
Output type		3-wire

Operating voltage	U_B	10 ... 30 V
Switching frequency	f	0 ... 30 Hz
Hysteresis	H	typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop	U_d	≤ 3 V
Operating current	I_L	0 ... 200 mA
Off-state current	I_r	0 ... 0.5 mA typ. 0.1 µA
No-load supply current	I₀	≤ 40 mA
Power consumption	P	≤ 420 W
Time delay before availability	t_v	≤ 300 ms
Status indicator		Dual color-LED, yellow/green SIO mode: yellow = switching state green = power supply on IO-Link mode: see manual

Interface type		IO-Link ( via C/Q = pin 4 )
IO-Link revision		1.1
Device profile		Identification and Diagnosis - I&D Smart Sensor - SSP 1.1
Process data		Input 5 Bit - switching signal 1 Bit - uncertainty indication 1 Bit - status signal 1 Bit - maintenance warning 1 Bit
Vendor ID		1 (0x0001)
Device ID		2098689 (0x200601)
Transfer rate		COM2 (38.4 kBit/s)
Min. cycle time		2.3 ms
SIO mode support		yes
Compatible master port type		Class A Class B (use 3-pole adapter or 3-wire cable)

Designation		Sync
Input/output type		1 synchronization connection, bidirectional

PWIS conformity

VDMA24364-B1/B2/C1/T220°C-W

Standard conformity

Standards		EN IEC 60947-5-2
Communication interface		IEC 61131-9 / IO-Link V1.1.3

Protection class

III

Rated insulation voltage	U_i	36 V
Rated impulse withstand voltage	U_imp	500 V

UL approval

cULus Listed, General Purpose, Class 2 Power Source

CCC approval

CCC approval / marking not required for products rated ≤36 V

Ambient temperature		Sensor head: 0 ... 250 °C (32 ... 482 °F) amplifier: 0 ... 70 °C (32 ... 158 °F)
Storage temperature		0 ... 70 °C (32 ... 158 °F)
Vibration resistance		30 g

Connection type

Connector plug

Degree of protection

Sensor head: IP65
amplifier: IP67

Material

Housing		Sensor head: PEEK 450, 30% fibre glass amplifier: Stainless steel 1.4305 / AISI 303
Mounting materials		Mounting bracket made of aluminum 3.3206

Connector

Threading		M12 x 1
Number of pins		4
Connection assembly		additional M8 plug connector on the sensor head side

Cable

Cable diameter		3.9 mm
Bending radius		fixed installation 7.5 x cable diameter movable installation 15 x cable diameter
Material		PFA
Color		black
Number of cores		3
Core cross section		0.34 mm²
Shield		grid
Length	L	1 m

Mass

481 g

Dimensions

Height		69 mm Sensor head
Width		65 mm Sensor head
Length		74 mm Sensor head

Mounting

amplifier: nuts, M18

Tightening torque

≤ 30 Nm

Default setting

PNP, NO

Scope of delivery

2 self locking nuts in scope of delivery

General Notes

We value your privacy!

We and our partners are using technologies like cookies and process personal data like the IP-address or browser information in order to personalize the advertising that you see. This helps us to show you more relevant ads and improves your internet experience. We also use it in order to measure results or align our website content. Because we value your privacy, we are herewith asking for your permission to use these technologies. You can always change/withdraw your consent later by clicking on the settings button on the left lower corner of the page.

Categories	Description	Status
Functional	These cookies are necessary so that you can navigate through the pages and use essential functions (e.g. login).
Analytics	We use these cookies and scripts to measure the visits and clicks on our website in order to constantly improve it.
Marketing	These cookies and similar technologies are used to provide you with personalized and therefore relevant advertising content.