AS-Interface sensor/actuator module VBA-2E2A-G2-ZEJ/XE2J

AS-Interface certificate
Degree of protection IP67
A/B node with extended addressing possibility for up to 62 nodes
Addressing jack
Flat cable connection with cable piercing technique, variable flat cable guide
Communication monitoring
Inputs for 2- and 3-wire sensors
Supply of the inputs and the outputs from AS-Interface
Two MOVI-SWITCH-1E, controllable by SEW
Ground connection (FE) possible
Function display for bus, inputs and outputs
Detection of overload on sensor supply
Detection of output overload

Technical Data
Product Documentation
Approvals
Associated Products

Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.

Ladda ned datablad som PDF::

Utdrag ur datablad: Tekniska data för VBA-2E2A-G2-ZEJ/XE2J

Product Description
G2 flat module 2 inputs (PNP) and 2 electronic outputs

General specifications
Node type		A/B node
AS-Interface specification		V3.0
Required gateway specification		≥ V2.1
UL File Number		E223772
Indicators/operating means
LED FAULT		error display; LED red red: communication error or address is 0 red flashing: overload of sensor power supply or outputs
LED PWR		AS-Interface voltage; LED green
LED IN		switching state (input); 2 LED yellow
LED OUT		Switching state (output); 2 LED yellow
Electrical specifications
Rated operating voltage		26.5 ... 31.6 V from AS-Interface
Rated operating current		≤ 40 mA (without sensors) / max. 170 mA
Protection class		III
Surge protection		U_e: Over voltage category III, safe isolated power supplies (PELV)
Input
Number/Type		2 inputs for 2- or 3-wire sensors (PNP), DC
Supply		from AS-Interface
Voltage		21 ... 31 V
Current loading capacity		≤ 130 mA (T_B ≤ 40 °C), ≤ 100 mA (T_B ≤ 60 °C), overload and short-circuit protected
Input current		≤ 8 mA (limited internally)
Switching point		according to DIN EN 61131-2 (Type 2)
	0 (unattenuated)	≤ 2 mA
	1 (attenuated)	≥ 4 mA
Output
Number/Type		2 electronic outputs, PNP overload and short-circuit proof
Supply		from AS-Interface
Current		limited by the current loading capacity of the module
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 62026-2:2013 EN 61000-6-2:2001 EN 61000-6-4:2001
Standard conformity
Degree of protection		EN 60529:2000
Input		EN 61131-2:2007
Emitted interference		EN 61000-6-4:2001
AS-Interface		EN 62026-2:2013
Noise immunity		EN 61000-6-2:2001
Programming instructions
Profile		S-B.A.E
IO code		B
ID code		A
ID1 code		7
ID2 code		E
Data bits (function via AS-Interface)		InputOutput
	D0	- OUT1
	D1	- OUT2
	D2	IN3 -
	D3	IN4 -
Parameter bits (programmable via AS-i)		function
	P0	not used
	P1	not used
	P2	not used
	P3	not used
Ambient conditions
Ambient temperature		-25 ... 60 °C (-13 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Relative humidity		85 % , noncondensing
Climatic conditions		For indoor use only
Altitude		≤ 2000 m above MSL
Pollution degree		3
Mechanical specifications
Degree of protection		IP67
Connection		cable piercing method: flat cable yellow inputs/outputs: M12 round connector
Material
	Housing	PBT
Mass		100 g
Tightening torque, cable gland		0.4 Nm
Mounting		Mounting plate

Classifications

System	Classcode
ECLASS 13.0	27242604
ECLASS 12.0	27242604
ECLASS 11.0	27242604
ECLASS 10.0.1	27242604
ECLASS 9.0	27242604
ECLASS 8.0	27242604
ECLASS 5.1	27242604
ETIM 9.0	EC001599
ETIM 8.0	EC001599
ETIM 7.0	EC001599
ETIM 6.0	EC001599
ETIM 5.0	EC001599
UNSPSC 12.1	39121535

Details: VBA-2E2A-G2-ZEJ/XE2J

Product Documentation: VBA-2E2A-G2-ZEJ/XE2J

Brief Instructions	Language	File Type	File Size
Instruction leaflet / Beipackzettel	ALL	PDF	188 KB

Approvals: VBA-2E2A-G2-ZEJ/XE2J

Certificates	Cert No.	Language	File Type	File Size
Canada, USA UL	CoC 20141115-E223772	ALL	PDF	342 KB
Worldwide AS-International Association AS-Interface	38702	ALL	PDF	607 KB
Declaration of Conformity
EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F)	DOC-1018C	ALL	PDF	118 KB

Associated Products: VBA-2E2A-G2-ZEJ/XE2J

Matching System Components

	U-G3FF AS-Interface module mounting base
	AS-Interface module mounting base for connection to flat cable (AS-Interface and external auxiliary power)fa

Accessories

	VBP-HH1-V3.0-KIT AS-Interface Handheld with accessory
	AS-Interface Handheld with accessoryfa

	VAZ-PK-1,5M-V1-G Adapter cable module/hand-held programming device
	Adapter cable module/hand-held programming devicefa

Allmänna kommentarer om produktinformationen från Pepperl+Fuchs

Free Download: White Paper on TCP-Based Communication Protocols (PDF)

This free PDF white paper compares the different TCP-based communication protocols (AMQP, OPC UA, MQTT, REST API) that have found their way up and are considered the enablers of IIoT and Industry 4.0. Get your free download now!

AS-Interface Switch Cabinet Module KE5 – Simple Handling and Improved Manageability

The unique housing design of the new KE5 switch cabinet module enables distinct visibility and simplifies mounting, wiring, and maintenance inside switch cabinets and junction boxes.

Download the AS-Interface Product Overview

Get to know our full range of AS-Interface products.

Pepperl+Fuchs AB
Bultgatan 40 A
442 40 Kungälv
Sverige
orgnr. 556212-2126
info@se.pepperl-fuchs.com
phone +46 303 246070

Pepperl+Fuchs is a leading developer and manufacturer of electronic sensors and components for the global automation market. Continuous innovation, enduring quality, and steady growth have been the foundation of our success for more than 70 years. Pepperl+Fuchs employs 6,300 people worldwide and has manufacturing facilities in Germany, USA, Singapore, Hungary, Indonesia and Vietnam, most of them ISO 9001 certified.