AS-Interface sensor/actuator module VAA-4E4A-KE5-ZEJQ/R-Y314457

Housing with push-in connection technology and mechanically coded terminal blocks
Housing width 19 mm, installation in the switch cabinet on DIN mounting rail
Selectable supply to the sensors: External or from the module
Function display for bus, internal sensor supply, inputs, and outputs

Technical Data
配套产品

请注意：所有以Pepperl + Fuchs GmbH或Pepperl + Fuchs AG名义发行的产品相关文件，例如证书，合格声明等，同样适用于Pepperl + Fuchs SE。

將完整的規格書下載為PDF:

產品規格摘要：的技術資料 VAA-4E4A-KE5-ZEJQ/R-Y314457

產品描述
Cabinet module 4 inputs and 4 relay outputs

General specifications
Node type		Standard node
AS-Interface specification		V3.0
Required gateway specification		≥ V2.0
UL File Number		E223772
MTBF		224 a
Indicators/operating means
LED FAULT		Fault display; Red LED red: Communication fault or address is 0 red, flashing: Overload, internal input supply
LED INT		Internal input supply active; LED green
LED PWR		AS-Interface voltage; green LED green: voltage OK flashing green: address 0
LED IN		switching state (input); 4 LED yellow
LED OUT		Switching state (output); 4 LED yellow
Electrical specifications
Auxiliary voltage (input)		12 ... 30 V DC PELV
Rated operating voltage		26.5 ... 31.6 V from AS-Interface
Rated operating current		≤ 35 mA (without sensors) / max. 230 mA
Surge protection		O1 ... O4: Over voltage category II U_EXT, U_e: overvoltage category II, safe isolated power supplies (PELV)
Input
Number/Type		4 inputs for 3-wire sensors (PNP), DC
Supply		from AS-Interface (switch position INT, default settings) or external U_EXT (switch position EXT)
Voltage		21 ... 31 V DC (INT)
Current loading capacity		≤ 150 mA, overload- and short-circuit protected (INT)
Input current		≤ 5.6 mA (max.)
Switching point		according to DIN EN 61131-2 (type 1)
	0 (unattenuated)	≤ 0.5 mA
	1 (attenuated)	≥ 2 mA
Signal delay		< 3 ms (Input/AS-Interface)
Output
Number/Type		4 relay outputs, normally open
Supply		none
Nominal load
	Per contact	2 A/30 VDC; 2 A/250 VAC For more information, see the "Galvanic Isolation" section
	Per module	8 A
Control circuit		≤ 11 mA per relay (from AS-Interface)
Switching delay		< 10 ms (AS-Interface/contact)
Usage category		DC-13 and AC-14
Switching
	Mechanical	5 x 10⁷
	Electrical	2 x 10⁵ (250 VAC, 2 A, cos φ = 0.4)
Galvanic isolation
Input/Output		safe isolation, Rated insulation voltage 252 Veff
Input/AS-Interface		Switch position INT: None Switch setting EXT: safe isolation, rated insulation voltage 92 Veff
Output/Output		Basic insulation, rated insulation voltage 250 V_eff, in phase
Output/AS-Interface		safe isolation, Rated insulation voltage 252 Veff
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 62026-2:2013
Low voltage
	Directive 2014/35/EU	EN 60664-1:2007
Standard conformity
Galvanic isolation		EN 60664-1:2007
Degree of protection		EN 60529:2000
Fieldbus standard		EN 62026-2:2013
Electrical safety		IEC 61140:2009
Input		EN 61131-2:2004
Emitted interference		EN 61000-6-4:2007
AS-Interface		EN 62026-2:2013
Noise immunity		EN 61000-6-2:2005, EN 61326-1:2006, EN 62026-2:2013
Programming instructions
Profile		S-7.F
IO code		7
ID code		F
ID1 code		F
ID2 code		F
Data bits (function via AS-Interface)		InputOutput
	D0	IN1 O1
	D1	IN2 O2
	D2	IN3 O3
	D3	IN4 O4
Parameter bits (programmable via AS-i)		function
	P0	Communication monitoring P0 = 0 monitoring = off, the outputs maintain the status if communication fails P0 = 1 monitoring = on, i.e. if communication fails, the outputs are deenergised (default settings)
	P1	not used
	P2	not used
	P3	not used
Ambient conditions
Ambient temperature		-25 ... 60 °C (-13 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Relative humidity		85 % , noncondensing
Climatic conditions		For indoor use only
Altitude		≤ 2000 m above MSL
Shock and impact resistance		15 g, 11 ms in 6 spatial directions, 3 shocks 10 g, 16 ms in 6 spatial directions, 1000 shocks
Vibration resistance		0.35 mm 10 ... 57 Hz , 5 g 57 ... 150 Hz, 20 cycles
Pollution degree		2
Mechanical specifications
Degree of protection		IP20 Installation in an enclosure with a minimum protection class of IP54 required
Connection		Removable push-in terminals rated connection capacity: rigid: 0.20 mm² ... 1.5 mm² flexible (without wire end ferrule): 0.20 mm² ... 2.5 mm² flexible (with wire end ferrule): 0.25 mm² ... 1.5 mm²
Material
	Housing	PA 66-FR
Mass		125 g
Dimensions
	Height	100 mm
	Width	18.9 mm
	Length	124 mm
Mounting		DIN mounting rail

Classifications

System	Classcode
ECLASS 13.0	27242604
ECLASS 12.0	27242604
ECLASS 11.0	27242604
ECLASS 10.0.1	27242604
ECLASS 9.0	27242604
ECLASS 8.0	27242604
ECLASS 5.1	27242604
ETIM 9.0	EC001599
ETIM 8.0	EC001599
ETIM 7.0	EC001599
ETIM 6.0	EC001599
ETIM 5.0	EC001599
UNSPSC 12.1	39121535

Details: VAA-4E4A-KE5-ZEJQ/R-Y314457

相關產品: VAA-4E4A-KE5-ZEJQ/R-Y314457

Accessories

	VBP-HH1-V3.0-KIT AS-Interface Handheld with accessory
	AS-Interface Handheld with accessoryfa

	VAZ-PK-1,5M-V1-G Adapter cable module/hand-held programming device
	Adapter cable module/hand-held programming devicefa

General Notes Relating to Pepperl+Fuchs Product Information

Free Download: White Paper on TCP-Based Communication Protocols (PDF)

免费下载：基于 TCP 标准的通信协议白皮书 (PDF)

这份免费的 PDF 白皮书比较了不同的基于TCP标准的通信协议（包括 AMQP、OPC UA、MQTT、REST API），这些协议已成为 IIoT 和工业 4.0 的推动力。立即免费下载！

AS-Interface Switch Cabinet Module KE5 – Simple Handling and Improved Manageability

The unique housing design of the new KE5 switch cabinet module enables distinct visibility and simplifies mounting, wiring, and maintenance inside switch cabinets and junction boxes.

Download the AS-Interface Product Overview

Get to know our full range of AS-Interface products.

台灣倍加福有限公司
信義路5段150巷2號21樓之4
信義區
11059 台北市臺灣
臺灣
fa-info@tw.pepperl-fuchs.com
phone +886 2 27227708

Pepperl+Fuchs 倍加福是領先全球的電子感測器 和 零組件的開發與製造商. 超過七十年的不斷創新、穩定的品質與持續的業績增長，成就了今日的我們， Pepperl+Fuchs 倍加福在全球擁有 6,300 名員工，並在德國、美國、新加坡、匈牙利、印尼和越南都設有製造工廠，其中多數工廠已通過 ISO 9001 認證