SMART Transmitter Power Supply HiC2025ES

1-channel isolated barrier
24 V DC supply (bus powered)
Input for 2-wire SMART transmitters and current sources
Output for 4 mA ... 20 mA or 1 V ... 5 V
Sink or source mode
Line fault detection (LFD)
Up to SIL 3 acc. to IEC/EN 61508

Technical Data
Product Documentation
Design / Simulation
Approvals
配套产品

请注意：所有以Pepperl + Fuchs GmbH或Pepperl + Fuchs AG名义发行的产品相关文件，例如证书，合格声明等，同样适用于Pepperl + Fuchs SE。

將完整的規格書下載為PDF:

產品規格摘要：的技術資料 HiC2025ES

General specifications
Signal type		Analog input
Functional safety related parameters
Safety Integrity Level (SIL)		SIL 3
Systematic capability (SC)		SC 3
Supply
Connection		SL1: 1a(-), 1b(-); 2a(+), 2b(+)
Rated voltage		19 ... 30 V DC bus powered via Termination Board
Ripple		≤ 10 %
Rated current		≤ 50 mA
Power dissipation		≤ 800 mW
Power consumption		≤ 1.2 W
Input
Connection side		field side
Connection		SL2: 5a(+), 1b(-); 5a(+), 5b(-)
Input signal		4 ... 20 mA , limited to approx. 27 mA reverse polarity protected
Line fault detection		downscaling ≤ 3 mA ; upscaling ≥ 22 mA
Voltage drop		approx. 5 V on SL2: 5a(+), 1b(-)
Available voltage		≥ 15 V at 20 mA on SL2: 5a(+), 5b(-)
Output
Connection side		control side
Connection		SL1: 8a(+), 7a(-)
Load		0 ... 300 Ω (source mode)
Output signal		source mode: 4 ... 20 mA or 1 ... 5 V (internal resistor: 250 Ω, 0.1 %) sink mode: 4 ... 20 mA, operating voltage 16 ... 28 V For additional internal or external loads the voltage drop has to be considered, e. g. 250 Ω x 20 mA = 5 V.
Ripple		20 mV _rms
Fault indication output
Connection		SL1: 6b
Output type		open collector transistor (internal fault bus)
Transfer characteristics
Deviation		at 20 °C (68 °F) ≤ ± 20 µA incl. calibration, linearity, hysteresis, loads and supply voltage fluctuations (source mode and sink mode 4 ... 20 mA) ≤ 10 mV incl. calibration, linearity, hysteresis and fluctuations of supply voltage (source mode 1 ... 5 V)
	Influence of ambient temperature	< 2 µA/K (0 ... 70 °C (32 ... 158 °F)); < 4 µA/K (-20 ... 0 °C (-4 ... 32 °F)) (source mode and sink mode 4 ... 20 mA) < 0.5 mV/K (0 ... 70 °C (32 ... 158 °F)); < 1 mV/K (-20 ... 0 °C (-4 ... 32 °F)) (source mode 1 ... 5 V)
Frequency range		field side into the control side: bandwidth with 1 mA_pp signal 0 ... 3 kHz (-3 dB) control side into the field side: bandwidth with 0.5 V_pp signal 0 ... 3 kHz (-3 dB)
Settling time		≤ 200 ms
Rise time/fall time		≤ 20 ms
Galvanic isolation
Input/Output		safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
Input/power supply		safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
Output/power supply		Basic isolation acc. to EN 61010-1 rated insulation voltage ≤ 50 V
Indicators/settings
Display elements		LEDs
Control elements		DIP switch
Factory setting		output: current source
Configuration		via DIP switches
Labeling		space for labeling at the front
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2013 (industrial locations)
Conformity
Electromagnetic compatibility		NE 21:2017 For further information see system description.
Degree of protection		IEC 60529:2001
Ambient conditions
Ambient temperature		-20 ... 70 °C (-4 ... 158 °F)
Mechanical specifications
Degree of protection		IP20
Mass		approx. 100 g
Dimensions		12.5 x 106 x 128 mm (0.5 x 4.2 x 5.1 inch) (W x H x D)
	Height	106 mm
	Width	12.5 mm
	Depth	128 mm
Mounting		on termination board
Coding		pin 1 and 3 trimmed For further information see system description.
Data for application in connection with hazardous areas
EU-type examination certificate		CESI 10 ATEX 063
	Marking	II (1)G [Ex ia Ga] IIC II (1)D [Ex ia Da] IIIC I (M1) [Ex ia Ma] I
	Input	Ex ia
Supply
	Maximum safe voltage	253 V AC (Attention! U_m is no rated voltage.)
Equipment		SL2: 5a(+), 5b(-)
	Voltage	25.2 V
	Current	100 mA
	Power	630 mW
	Internal capacitance	5.7 nF
	Internal inductance	negligible
Equipment		SL2: 5a(+), 1b(-)
	Voltage	< 30 V
	Current	< 128 mA
	Voltage	7.2 V
	Current	100 mA
	Power	25 mW
	Internal capacitance	5.7 nF
	Internal inductance	negligible
Certificate		CESI 19 ATEX 016 X
	Marking	II 3G Ex ec IIC T4 Gc
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2012+A11:2013 , EN 60079-11:2012 , EN 60079-7:2015
International approvals
UL approval		E106378
	Control drawing	116-0376 (cULus)
IECEx approval
	IECEx certificate	IECEx CES 10.0021X
	IECEx marking	[Ex ia Ga] IIC , [Ex ia Da] IIIC , [Ex ia Ma] I Ex ec IIC T4 Gc
General information
Supplementary information		Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.

Classifications

System	Classcode
ECLASS 13.0	27210119
ECLASS 12.0	27210119
ECLASS 11.0	27210119
ECLASS 10.0.1	27210119
ECLASS 9.0	27210119
ECLASS 8.0	27210119
ECLASS 5.1	27210119
ETIM 9.0	EC001485
ETIM 8.0	EC001485
ETIM 7.0	EC001485
ETIM 6.0	EC001485
ETIM 5.0	EC001485
UNSPSC 12.1	32101514

Details: HiC2025ES

Product Documentation: HiC2025ES

Safety and Security Documentation	語言	檔案類型	檔案尺寸
Instruction manual	ENG	PDF	167 KB
Safety Manual	ENG	PDF	427 KB
Manuals
System Manual	ENG	PDF	5438 KB

Design / Simulation: HiC2025ES

CAD	語言	檔案類型	檔案尺寸
CAD 3-D / CAD 3-D	ALL	STP	2770 KB
CAD Portal / CAD Portal	ALL	LINK	---

Approvals: HiC2025ES

Certificates	證書號碼	語言	檔案類型	檔案尺寸
CESI IECEx Certificate of Conformity	IECEx CES 10.0021X	ALL	LINK	---
China SITIIAS CCC Ex Certificate	2021322316003614 (Singapore)	ALL	PDF	1095 KB
Europe CESI ATEX Category (1) D ATEX Category (M1) ATEX Category (1) G	CESI 10 ATEX 063	ALL	PDF	661 KB
Europe CESI ATEX Category 3 G	CESI 19 ATEX 016X	ALL	PDF	432 KB
Europe Pepperl+Fuchs Certificate of Compliance ATEX Category 3	PF 10 CERT 1748 X	ALL	PDF	219 KB
India PESO (India) CCOE	A/P/HQ/KA/104/6083 (P576893)	ALL	PDF	124 KB
TÜV SÜD Functional Safety Certificate	C-IS-204399-01	ALL	PDF	188 KB
USA Canada UL Hazardous Location Certificate of Compliance cULus UL E106378	CoC 20140226 - E106378 RepRef 20140221	ALL	PDF	427 KB
Control Drawings
Control drawing UL / Control drawing UL		ALL	PDF	129 KB
Declaration of Conformity
EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F)	DOC-0776D	ALL	PDF	82 KB

相關產品: HiC2025ES

Accessory of

	HiCTB08-FBM-RAC-SC-IO08 Termination Board
	System board for Schneider, Foxboro FBM series, For 8 modules, For 8-channel cards FBM201/214(b)/216(b) (AI), FBM215/218/237 (AO), FBM204/205 (AO/AI), FBM244 (AI/AO), FBM247/248 (UIO), 24 V DC supply, Recommended modules: HiC2025(A) (AI), HiC2025ES (AI), HiC2031 (AO), HiC2081 (TI), HiC2831R5 (DI), HiC2883 (DO), HiC2441 (UIO), Hazardous area: screw terminals, blue, Non-hazardous area: Sub-D connector (male), 25-pin, Number of modules: 8, Signal type: Universal, Manufacturer: Foxboropa

	HiCTB16-FBM-RAC-SC-AI16 Termination Board
	System board for Schneider, Foxboro FBM series, For 16 modules, For 16-channel AI card FBM211, 24 V DC supply, Recommended modules: HiC2025(A) (AI), HiC2025ES (AI), HiC2081 (TI), Hazardous area: screw terminals, blue, Non-hazardous area: Sub-D connector (male), 37-pin, Number of modules: 16, Signal type: Analog input, Manufacturer: Foxboro, Control system type: FBMpa

	HiCTB16-TRX-RAC-PL-IO16 Termination Board
	System board for Schneider Electric, Tricon CX series by Triconex, TAN48 approval, For 16-channel universal I/O card 3902(A)X and AO card 3809(A)X, For 16 modules, Supported signal types: DI/DO/AI/TI/AO/UIO, 24 V DC supply, Hazardous area: pluggable screw terminals, blue, Non-hazardous area: Sub-D connector (male), 50-pin, Up to SIL 3 acc. to IEC/EN 61508, Number of modules: 16, Signal type: Analog output Universal, Manufacturer: Triconex, Control system type: Tricon CXpa

	HiCTB16-TRX-RAC-PL-AI16 Termination Board
	System board for Schneider Electric, Tricon CX series by Triconex, TAN48 approval, For 32-channel (16+16) AI cards 3722X and 3723X, For 16 modules, Recommended modules: HiC2025(A) (AI), HiC2025ES (AI), HiC2081 (TI), 24 V DC supply, Hazardous area: pluggable screw terminals, blue, Non-hazardous area: ELCO socket, 56-pin, Number of modules: 16, Signal type: Analog input, Manufacturer: Triconex, Control system type: Tricon CXpa

General Notes Relating to Pepperl+Fuchs Product Information

快速連結

Selector for Safety Products

Choose from various selection criteria like safety integrity level, performance level, device function, and signal type and find the SIL/PL assessed device that you are looking for.

台灣倍加福有限公司
信義路5段150巷2號21樓之4
信義區
11059 台北市臺灣
臺灣
fa-info@tw.pepperl-fuchs.com
phone +886 2 27227708

Pepperl+Fuchs 倍加福是領先全球的電子感測器 和 零組件的開發與製造商. 超過七十年的不斷創新、穩定的品質與持續的業績增長，成就了今日的我們， Pepperl+Fuchs 倍加福在全球擁有 6,300 名員工，並在德國、美國、新加坡、匈牙利、印尼和越南都設有製造工廠，其中多數工廠已通過 ISO 9001 認證