Switch Amplifier HiC2831R1

1-channel isolated barrier
24 V DC supply (bus powered)
Dry contact or NAMUR inputs
Application-specific outputs
Usable as signal splitter (1 input and 2 outputs)
2 passive transistor outputs (resistive)
Line fault transparency (LFT)
Up to SIL 2 acc. to IEC 61508

Technical Data
Product Documentation
Design / Simulation
Approvals

请注意：所有以Pepperl + Fuchs GmbH或Pepperl + Fuchs AG名义发行的产品相关文件，例如证书，合格声明等，同样适用于Pepperl + Fuchs SE。

將完整的規格書下載為PDF:

產品規格摘要：的技術資料 HiC2831R1

General specifications
Signal type		Digital Input
Supply
Connection		SL1: 1a(-), 1b(-); 2a(+), 2b(+)
Rated voltage		19 ... 30 V DC via Termination Board
Ripple		≤ 10 %
Rated current		≤ 25 mA
Power dissipation		≤ 500 mW
Power consumption		≤ 600 mW
Input
Connection		SL2: 5a(+), 5b(-)
Rated values		acc. to EN 60947-5-6 (NAMUR), see manual for electrical data
Open circuit voltage/short-circuit current		approx. 10 V DC / approx. 8 mA
Switching point/switching hysteresis		1.2 ... 2.1 mA / approx. 0.2 mA
Line fault detection		breakage I ≤ 0.1 mA , short-circuit I ≥ 6.5 mA
Pulse/Pause ratio		min. 100 µs / min. 100 µs
Output
Connection		SL1: 8a(+), 7a(-); 10a(+), 9a(-)
Rated voltage		19 ... 30 V DC with external resistance > 2 kΩ, e. g. 16-channel ProSafe DI card SDV144 from Yokogawa
Response time		≤ 200 µs
Output I, II		signal or fault message, passive transistor output (resistive) 0-signal: 33 kΩ ± 5 % + voltage drop 6.5 V ± 0.5 V 1-signal: voltage drop 6.5 V ± 0.5 V fault: > 100 kΩ
Fault indication output
Connection		SL1: 6b
Output type		open collector transistor (internal fault bus)
Transfer characteristics
Switching frequency		≤ 5 kHz
Galvanic isolation
Output/power supply		basic insulation according to IEC/EN 61010-1, rated insulation voltage 60 V_eff
Output/Output		basic insulation according to IEC/EN 61010-1, rated insulation voltage 60 V_eff
Indicators/settings
Display elements		LED PWR ON (power supply), one green LED LED STATUS (output status), one bicolored LED (yellow) LED FAULT (lead fault), one bicolored LED (red)
Control elements		DIP switches at the housing side for: - mode of operation input - output - lead fault detection enable/disable
Labeling		space for labeling at the front
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2013 (industrial locations)
Conformity
Electromagnetic compatibility		NE 21:2012 , EN 61326-3-2:2008
Degree of protection		IEC 60529:2001
Protection against electrical shock		IEC 61010-1
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Mechanical specifications
Degree of protection		IP20
Mass		approx. 100 g
Dimensions		12.5 x 106 x 128 mm (0.5 x 4.2 x 5.1 inch)
	Height	128 mm
	Width	12.5 mm
	Length	106 mm
Mounting		on termination board
Coding		pin 1 and 2 trimmed For further information see system description.
Data for application in connection with hazardous areas
EU-type examination certificate		BVS 11 ATEX E 026
	Marking	II (1) G [Ex ia] IIC, II (1) D [Ex ia] IIIC I (M1) [Ex ia] I
	Input	Ex ia
	Voltage	10.5 V
	Current	17.1 mA
	Power	45 mW (linear characteristic)
Supply
	Maximum safe voltage	253 V AC (Attention! U_m is no rated voltage.)
Output
	Maximum safe voltage	253 V AC (Attention! U_m is no rated voltage.)
Certificate		KIWA 15 ATEX 0037 X
	Marking	II 3G Ex nA IIC T4 Gc
Galvanic isolation
	Input/Output	safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
	Input/power supply	safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2012+A11:2013 , EN 60079-11:2012 , EN 60079-15:2010 , EN 50303:2000
International approvals
UL approval
	Control drawing	116-0331
IECEx approval		IECEx BVS 11.0040
	Approved for	[Ex ia Ga] IIC, [Ex ia] IIIC , [Ex ia] I
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.

Classifications

System	Classcode
ECLASS 13.0	27210121
ECLASS 12.0	27210121
ECLASS 11.0	27210121
ECLASS 10.0.1	27210121
ECLASS 9.0	27210121
ECLASS 8.0	27210121
ECLASS 5.1	27210121
ETIM 9.0	EC001485
ETIM 8.0	EC001485
ETIM 7.0	EC001485
ETIM 6.0	EC001485
ETIM 5.0	EC001485
UNSPSC 12.1	32101514

Details: HiC2831R1

Product Documentation: HiC2831R1

Safety and Security Documentation	語言	檔案類型	檔案尺寸
Instruction manual	ENG	PDF	168 KB
Functional Safety Manual	ENG	PDF	2014 KB
Manuals
System Manual	ENG	PDF	5438 KB

Design / Simulation: HiC2831R1

CAD	語言	檔案類型	檔案尺寸
CAD 2-D / CAD 2-D	ALL	ZIP	16364 KB

Approvals: HiC2831R1

Certificates	證書號碼	語言	檔案類型	檔案尺寸
Brasil TUV Rheinland Brazil	TÜV 16.0821	ALL	PDF	1136 KB
Canada FM	FM 17 CA 0057X	ALL	PDF	328 KB
Europe KIWA ATEX Category 3 G	KIWA 15 ATEX 0037X	ALL	PDF	988 KB
KIWA IECEx Certificate of Conformity Zone 2	IECEx KIWA 15.0019X	ALL	LINK	---
Korea KOSHA	15-AV4BO-0596	ALL	PDF	611 KB
USA FM	FM 17 US 0111X	ALL	PDF	330 KB
Control Drawings
Control drawing UL / Control drawing UL		ALL	PDF	136 KB

General Notes Relating to Pepperl+Fuchs Product Information

快速連結

Selector for Safety Products

Choose from various selection criteria like safety integrity level, performance level, device function, and signal type and find the SIL/PL assessed device that you are looking for.

台灣倍加福有限公司
信義路5段150巷2號21樓之4
信義區
11059 台北市臺灣
臺灣
fa-info@tw.pepperl-fuchs.com
phone +886 2 27227708

Pepperl+Fuchs 倍加福是領先全球的電子感測器 和 零組件的開發與製造商. 超過七十年的不斷創新、穩定的品質與持續的業績增長，成就了今日的我們， Pepperl+Fuchs 倍加福在全球擁有 6,300 名員工，並在德國、美國、新加坡、匈牙利、印尼和越南都設有製造工廠，其中多數工廠已通過 ISO 9001 認證