NRN10-12GM40-E2-IO-C-V1 Inductive sensor

Key Benefits at a Glance

10 mm non-flush
Reduction factor = 1
Magnetic field resistant
Weld Immune
IO-Link interface for service and process data
Switch point mode or window mode can be set
Switching function, stability alarm and pulse extension can be set

Please contact us for exact delivery estimation.173.00 USD

Product photo: Inductive sensor NRN10-12GM40-E2-IO-C-V1

Dimensions: Inductive sensor NRN10-12GM40-E2-IO-C-V1

Note

All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.

Datasheet Function Classification Product Documentation Design / Simulation Approvals Software Related Products

Technical data of NRN10-12GM40-E2-IO-C-V1

Switching function		Normally open/closed (NO/NC) programmable
Output type		PNP
Rated operating distance	s_n	10 mm (factory setting)
Near operating distance		8 mm (can be activated by software)
Installation		non-flush
Output polarity		DC
Assured operating distance	s_a	0 ... 8.1 mm
Reduction factor r_Al		1
Reduction factor r_Cu		1
Reduction factor r₃₀₄		1
Reduction factor r_St37		1
Output type		3-wire

Operating voltage	U_B	10 ... 30 V DC
Switching frequency	f	0 ... 1300 Hz (switch point mode) 0 ... 80 Hz (window mode, switch point mode with stability alarm)
Hysteresis	H	typ. 3 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		pulsing
Voltage drop	U_d	≤ 0.5 V
Operating current	I_L	0 ... 200 mA
Off-state current	I_r	0 ... 0.5 mA typ. 60 µA at 25 °C
No-load supply current	I₀	≤ 15 mA
Time delay before availability	t_v	max. 150 ms
Constant magnetic field	B	200 mT
Alternating magnetic field	B	200 mT
Status indicator		Multihole-LED, yellow

MTTF_d		362 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %

Interface type		IO-Link ( via C/Q = pin 4 )
IO-Link revision		1.1
Device ID		0x201114 (2101524)
Transfer rate		COM2 (38.4 kBit/s)
Min. cycle time		2.3 ms
Process data width		Process data input (control system side): 2 Bit Process data output (control system side): none
SIO mode support		yes
Compatible master port type		A

Standard conformity

Standards

EN IEC 60947-5-2

Protection class

Rated insulation voltage	U_i	60 V
Rated impulse withstand voltage	U_imp	800 V

UL approval

cULus Listed, General Purpose
Class 2 power source

CCC approval

CCC approval / marking not required for products rated ≤36 V

Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)

Connection type

Connector plug M12 x 1 , 4-pin

Housing material

Brass, PTFE coated

Sensing face

PPS

Degree of protection

IP67

Mass

24 g

Dimensions

Length		55 mm
Diameter		12 mm

Default setting

operating mode = switch point mode with stability alarm
switching function = Normally open (NO)
switching distance = 10 mm

Scope of delivery

2 self locking nuts in scope of delivery

General Notes

We value your privacy!

We and our partners are using technologies like cookies and process personal data like the IP-address or browser information in order to personalize the advertising that you see. This helps us to show you more relevant ads and improves your internet experience. We also use it in order to measure results or align our website content. Because we value your privacy, we are herewith asking for your permission to use these technologies. You can always change/withdraw your consent later by clicking on the settings button on the left lower corner of the page.

Categories	Description	Status
Functional	These cookies are necessary so that you can navigate through the pages and use essential functions (e.g. login).
Analytics	We use these cookies and scripts to measure the visits and clicks on our website in order to constantly improve it.
Marketing	These cookies and similar technologies are used to provide you with personalized and therefore relevant advertising content.