Yhteydenotto, Koneautomaatio
+358 20 7861 290
Yhteydenotto, Prosessiautomaatio
+358 20 7861 291
Not available for purchase
Slip- and rotation detection controller KFD2-UFT-Ex2.D
- 2 inputs
- Control circuit EEx ia IIC
- 2 relay outputs
- 2 electronic outputs, isolated
- Reset input
- Lead breakage monitoring (can be deactivated)
- Parameterization via keypad
- Input frequency 0.001 Hz ... 1 kHz (synchronization monitor function 10 Hz ... 1 kHz)
Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.
Lataa koko tietolomake PDF-tiedostona:
Ote tietolomakkeesta: Tekniset tiedot KFD2-UFT-Ex2.D
| General specifications | ||
|---|---|---|
| Signal type | Digital Input | |
| Supply | ||
| Connection | terminals 23+, 24- or power feed module/Power Rail | |
| Rated voltage | 20 ... 30 V DC | |
| Rated current | approx. 130 mA | |
| Power dissipation | 2.2 W | |
| Power consumption | 2.5 W | |
| Input | ||
| Connection | input I: terminals 1+, 3- input II: terminals 4+, 6- input III: terminals 13+, 14- (reset) input IV: Terminals 15+, 14- (Hold) |
|
| Function | reset: rotation direction signaling: reset in preferred direction (left-hand rotation) slip monitoring: reset slip error hold: slip monitoring: if the input is bridged, the Hold function becomes active. Lead fault is only indicated by relay 2 and combined fault indication. The condition of the relay is hold during fault. |
|
| Input I, II | acc. to EN 60947-5-6 (NAMUR) | |
| Open circuit voltage/short-circuit current | 8.2 V / 10 mA | |
| Pulse duration | min. 200 µs overlapping by rotation direction signaling: ≥ 100 µs | |
| Input frequency | rotation direction monitoring 0.001 ... 1000 Hz slip monitoring 10 ... 1000 Hz | |
| Line fault detection | breakage I ≤ 0.15 mA; short-circuit I > 6.5 mA | |
| Input III, IV | ||
| Active/Passive | I > 4 mA (for min. 100 ms) / I < 1.5 mA | |
| Open circuit voltage/short-circuit current | 18 V / 5 mA | |
| Output | ||
| Connection | output I: terminals 10, 11, 12 output II: terminals 16, 17, 18 output III: terminals 19+, 20- output IV: terminals 21+, 20- |
|
| Output I, II | signal , relay | |
| Contact loading | 250 V AC / 2 A / cos φ ≥ 0.7 ; 40 DC / 2 A | |
| Mechanical life | 5 x 107 switching cycles | |
| Energized/De-energized delay | approx. 20 ms / approx. 20 ms | |
| Output III and IV | signal , electronic output, passive | |
| Contact loading | 40 V DC | |
| Signal level | 1-signal: (L+) -2.5 V (50 mA, short-circuit/overload proof) 0-signal: switched off (off-state current ≤ 10 µA) |
|
| Programming interface | ||
| Connection | programming socket | |
| Interface | RS 232 | |
| Transfer characteristics | ||
| Input I | ||
| Resolution | slip monitoring : 1 % | |
| Influence of ambient temperature | 0.003 %/K (30 ppm) | |
| Output I, II | ||
| Response delay | ≤ 200 ms | |
| Galvanic isolation | ||
| Output I, II/other circuits | reinforced insulation according to IEC 61140, rated insulation voltage 300 Veff | |
| Mutual output I, II, III | reinforced insulation according to IEC 61140, rated insulation voltage 300 Veff | |
| Mutual output I, II, IV | reinforced insulation according to IEC 61140, rated insulation voltage 300 Veff | |
| Output III, IV/power supply and collective error | reinforced insulation according to IEC 61140, rated insulation voltage 300 Veff | |
| Output III/IV/Start-up override | functional insulation acc. to DIN EN 50178, rated insulation voltage 300 Veff | |
| Start-up override/power supply and collective error | reinforced insulation according to IEC 61140, rated insulation voltage 300 Veff | |
| Interface/power supply | reinforced insulation according to IEC 61140, rated insulation voltage 300 Veff | |
| Interface/output III, IV | functional insulation acc. to DIN EN 50178, rated insulation voltage 300 Veff | |
| Directive conformity | ||
| Electromagnetic compatibility | ||
| Directive 2004/108/EC | EN 61326-1:2006 | |
| Low voltage | ||
| Directive 2006/95/EC | EN 50178:1997 | |
| Conformity | ||
| Insulation coordination | EN 50178 | |
| Galvanic isolation | EN 50178 | |
| Electromagnetic compatibility | NE 21 | |
| Degree of protection | IEC 60529 | |
| Ambient conditions | ||
| Ambient temperature | -20 ... 50 °C (-4 ... 122 °F) | |
| Mechanical specifications | ||
| Degree of protection | IP20 | |
| Mass | 300 g | |
| Dimensions | 40 x 100 x 115 mm (1.6 x 3.9 x 4.5 inch) | |
| Height | 100 mm | |
| Width | 40 mm | |
| Length | 115 mm | |
| Data for application in connection with hazardous areas | ||
| EU-type examination certificate | TÜV 99 ATEX 1471 , for additional certificates see www.pepperl-fuchs.com | |
| Marking |  II (1)GD [EEx ia] IIC [circuit(s) in zone 0/1/2] |
|
| Supply | ||
| Maximum safe voltage | 40 V DC (Attention! Um is no rated voltage.) | |
| Input I and II | terminals 1+, 3-; 4+, 6- EEx ia IIC | |
| Voltage | 10.1 V | |
| Current | 13 mA | |
| Power | 34 mW (linear characteristic) | |
| Input III and IV | terminals 13+, 14-; 15+, 14- non-intrinsically safe | |
| Maximum safe voltage | 40 V DC (Attention! Um is no rated voltage.) | |
| Output I, II | terminals 10, 11, 12; 16, 17, 18 non-intrinsically safe | |
| Maximum safe voltage | 253 V AC / 40 V DC (Attention! Um is no rated voltage.) | |
| Contact loading | 253 V AC/2 A/cos φ > 0.7; 40 V DC/2 A resistive load (TÜV 99 ATEX 1471) 50 V AC/2 A/cos φ > 0.7; 40 V DC/2 A resistive load (TÜV 02 ATEX 1885 X) |
|
| Output III and IV | terminals 19, 20, 21 non-intrinsically safe | |
| Maximum safe voltage | 40 V DC (Attention! Um is no rated voltage.) | |
| Certificate | TÜV 02 ATEX 1885 X , observe statement of conformity | |
| Marking | II 3G EEx nAC IIC T4 [device in zone 2] |
|
| Galvanic isolation | ||
| Input/Other circuits | safe galvanic isolation acc. to EN 50020, voltage peak value 375 V | |
| Directive conformity | ||
| Directive 94/9/EC | EN 50014, EN 50020, EN 50021 | |
Classifications
| System | Classcode |
|---|---|
| ECLASS 13.0 | 27210128 |
| ECLASS 12.0 | 27210128 |
| ECLASS 11.0 | 27210128 |
| ECLASS 10.0.1 | 27210128 |
| ECLASS 9.0 | 27210128 |
| ECLASS 8.0 | 27210190 |
| ECLASS 5.1 | 27210121 |
| ETIM 9.0 | EC002918 |
| ETIM 8.0 | EC002918 |
| ETIM 7.0 | EC002918 |
| ETIM 6.0 | EC002918 |
| ETIM 5.0 | EC002475 |
| UNSPSC 12.1 | 39121007 |
Details: KFD2-UFT-Ex2.D
Product Documentation: KFD2-UFT-Ex2.D
| Manuals | Kieli | Tiedostotyyppi | Tiedoston koko |
|---|---|---|---|
| Manual KF**-UFT-(Ex)2.D | ENG | 351 KB | |
| Manual | ENG | 3685 KB |
Approvals: KFD2-UFT-Ex2.D
| Certificates | Sertifikaatin nro | Kieli | Tiedostotyyppi | Tiedoston koko |
|---|---|---|---|---|
| Europe TUV Nord ATEX Category 3 G | TÜV 02 ATEX 1885X | ALL | 1101 KB |
Choose from various selection criteria like safety integrity level, performance level, device function, and signal type and find the SIL/PL assessed device that you are looking for.
Pepperl+Fuchs Oy
Areenakatu 7
FI-37570 Lempäälä
Finland
info@fi.pepperl-fuchs.com
+358 20 7861 290
info@fi.pepperl-fuchs.com
+358 20 7861 291
© 2024 Kaikki oikeudet pidätetään.
Pepperl+Fuchs on dynaaminen ja tulevaisuuteen suuntaava yritys joka myy konepajateollisuuden, robotiikan ja teollisuusautomaation komponentteja. Tuotannon sujuvuus, tuotteiden korkea laatu ja niiden maailmanlaajuinen saatavuus ovat tuoneet yritykselle menestystä jo yli 70 vuoden ajan. Pepperl+Fuchs työllistää maailman laajuisesti yhteensä noin 6300 henkilöä. Globaalilla yrityksellä on tuotantolaitoksia Saksassa, Singaporessa, Yhdysvalloissa, Unkarissa, Indonesiassa ja Vietnamissa, joista suurin osa ovat ISO 9001-sertifioitu.