Frequency Converter with Direction and Synchronization Monitor KFU8-UFT-Ex2.D

2-channel isolated barrier
Universal usage at different power supplies
Dry contact or NAMUR inputs
Input frequency 1 mHz ... 1 kHz
Current output 0/4 mA ... 20 mA
Relay and transistor output
Start-up override
Configurable by PACTware or keypad
Line fault detection (LFD)

Technical Data
Product Documentation
Design / Simulation

Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.

Lataa koko tietolomake PDF-tiedostona:

Ote tietolomakkeesta: Tekniset tiedot KFU8-UFT-Ex2.D

Tuotekuvaus
48 V AC ... 253 V AC/20 V DC ... 90 V DC

General specifications
Signal type		Digital Input
Supply
Connection		terminals 23, 24
Rated voltage		20 ... 90 V DC / 48 ... 253 V AC 50 ... 60 Hz
Rated current		approx. 130 mA
Power dissipation		2.2 W / 3.5 VA
Power consumption		2.5 W / 5 VA
Input
Connection		input I: terminals 1+, 3- input II: terminals 4+, 6- input III: terminals 13+, 14- (control input 1) input IV: terminals 15+, 14- (control input 2)
Input I, II		acc. to EN 60947-5-6 (NAMUR)
	Open circuit voltage/short-circuit current	8.2 V / 10 mA
	Pulse duration	min. 250 µs , overlap on direction of rotation signal: ≥ 125 µs
	Input frequency	rotation direction monitoring 0.001 ... 1000 Hz slip monitoring 10 ... 1000 Hz
	Line fault detection	breakage I ≤ 0.15 mA; short-circuit I > 6.5 mA
Input III, IV
	Active/Passive	I > 4 mA (for min. 100 ms) / I < 1.5 mA
	Open circuit voltage/short-circuit current	18 V / 5 mA
Output
Connection		output I: terminals 10, 11, 12 output II: terminals 16, 17, 18 output III: terminals 19+, 20- output IV: terminals 21+, 20- output V: terminals 7-, 8+
Output I, II		signal , relay
	Contact loading	250 V AC / 2 A / cos φ ≥ 0.7 ; 40 V DC / 2 A
	Mechanical life	5 x 10⁷ switching cycles
	Energized/De-energized delay	approx. 20 ms / approx. 20 ms
Output III and IV		signal , electronic output, passive
	Contact loading	40 V DC
	Signal level	1-signal: (L+) -2.5 V (50 mA, short-circuit/overload proof) 0-signal: switched off (off-state current ≤ 10 µA)
Output V		analog
	Current range	0 ... 20 mA or 4 ... 20 mA
	Open loop voltage	max. 24 V DC
	Load	max. 650 Ω
	Fault signal	downscale I ≤ 3.6 mA, upscale I ≥ 21.5 mA (acc. NAMUR NE43)
Programming interface
	Connection	programming socket
	Interface	RS 232
Transfer characteristics
Input I and II
	Measurement range	0.001 ... 1000 Hz
	Resolution	slip monitoring: 1% frequency measurement: 0,1% of measured value; but >0.001Hz
	Accuracy	slip monitoring: 1% frequency measurement: 0.5% of measured value; but >0.001Hz
	Measuring time	frequency measurement: < 100 ms
	Influence of ambient temperature	0.003 %/K (30 ppm)
Output I, II
	Response delay	≤ 200 ms
Output V
	Resolution	< 10 µA
	Accuracy	< 30 µA
	Influence of ambient temperature	0.005 %/K (50 ppm)
Galvanic isolation
Input III, IV/power supply		reinforced insulation according to IEC 61140, rated insulation voltage 300 V_eff
Output I, II/other circuits		reinforced insulation according to IEC 61140, rated insulation voltage 300 V_eff
Mutual output I, II, III		reinforced insulation according to IEC 61140, rated insulation voltage 300 V_eff
Mutual output I, II, IV		reinforced insulation according to IEC 61140, rated insulation voltage 300 V_eff
Output III, IV/power supply		reinforced insulation according to IEC 61140, rated insulation voltage 300 V_eff
Output III, IV/input III, IV		basic insulation according to IEC 61140, rated insulation voltage 50 V_eff
Output III, IV/V		basic insulation according to IEC 62103, rated insulation voltage 50 V_eff
Output V/power supply		reinforced insulation according to IEC 61140, rated insulation voltage 300 V_eff
Interface/power supply		reinforced insulation according to IEC 61140, rated insulation voltage 300 V_eff
Interface/output III, IV		basic insulation according to IEC 62103, rated insulation voltage 50 V_eff
Directive conformity
Electromagnetic compatibility
	Directive 2004/108/EC	EN 61326-1:2006
Low voltage
	Directive 2006/95/EC	EN 50178:1997
Conformity
Insulation coordination		IEC 62103
Galvanic isolation		IEC 62103
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Protection against electrical shock		IEC 61140
Input		EN 60947-5-6
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Mechanical specifications
Degree of protection		IP20
Mass		300 g
Dimensions		40 x 119 x 115 mm (1.6 x 4.7 x 4.5 inch) , housing type C2
	Height	119 mm
	Width	40 mm
	Length	115 mm
Data for application in connection with hazardous areas
EU-type examination certificate		TÜV 99 ATEX 1471 , for additional certificates see www.pepperl-fuchs.com
	Marking	II (1)GD, I (M1) [Ex ia] IIC, [Ex iaD], [Ex ia] I (-20 °C ≤ T_amb ≤ 60 °C)
Supply
	Maximum safe voltage	253 V AC / 125 V DC (Attention! U_m is no rated voltage.)
Input I and II		terminals 1+, 3-; 4+, 6- Ex ia IIC, Ex iaD
	Voltage U_o	10.1 V
	Current I_o	13.5 mA
	Power P_o	34 mW (linear characteristic)
Input III and IV		terminals 13+, 14-; 15+, 14- non-intrinsically safe
	Maximum safe voltage U_m	40 V (Attention! U_m is no rated voltage.)
Output I, II		terminals 10, 11, 12; 16, 17, 18 non-intrinsically safe
	Maximum safe voltage	253 V (Attention! The rated voltage can be lower.)
	Contact loading	253 V AC/2 A/cos φ > 0.7; 40 V DC/2 A resistive load (TÜV 99 ATEX 1471)
Output III and IV		terminals 19, 20, 21 non-intrinsically safe
	Maximum safe voltage U_m	40 V (Attention! U_m is no rated voltage.)
Output V		terminals 8+, 7- non-intrinsically safe
	Maximum safe voltage U_m	40 V DC (Attention! U_m is no rated voltage.)
Interface		RS 232
	Maximum safe voltage	40 V (Attention! U_m is no rated voltage.)
Galvanic isolation
	Input I, II/other circuits	safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 94/9/EC	EN 60079-0:2006, EN 60079-11:2007, EN 60079-26:2007 , EN 61241-0: 2006, EN 61241-11: 2006
International approvals
FM approval
	Control drawing	16-538FM-12
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.

Classifications

System	Classcode
ECLASS 13.0	27210128
ECLASS 12.0	27210128
ECLASS 11.0	27210128
ECLASS 10.0.1	27210128
ECLASS 9.0	27210128
ECLASS 8.0	27210190
ECLASS 5.1	27210121
ETIM 9.0	EC002918
ETIM 8.0	EC002918
ETIM 7.0	EC002918
ETIM 6.0	EC002918
ETIM 5.0	EC002475
UNSPSC 12.1	39121007

Details: KFU8-UFT-Ex2.D

Product Documentation: KFU8-UFT-Ex2.D

Brief Instructions	Kieli	Tiedostotyyppi	Tiedoston koko
Operator card KF-UFT-2.D / Bedienkarte KF-UFT-2.D	ALL	PDF	831 KB
Manuals
Manual KF**-UFT-(Ex)2.D	ENG	PDF	1611 KB
Manual	ENG	PDF	3685 KB

Design / Simulation: KFU8-UFT-Ex2.D

CAD	Kieli	Tiedostotyyppi	Tiedoston koko
CAD 2-D / CAD 2-D	ALL	ZIP	657 KB
CAD 3-D / CAD 3-D	ALL	STP	870 KB
CAD Portal / CAD Portal	ALL	LINK	---
CAE
EPLAN macro EDZ / EPLAN Makro EDZ	ALL	EDZ	81 KB

General Notes Relating to Pepperl+Fuchs Product Information

Pikalinkit

Selector for Safety Products

Choose from various selection criteria like safety integrity level, performance level, device function, and signal type and find the SIL/PL assessed device that you are looking for.

Pepperl+Fuchs Oy
Areenakatu 7
FI-37570 Lempäälä
Finland
info@fi.pepperl-fuchs.com
phone +358 20 7861 290
info@fi.pepperl-fuchs.com
phone +358 20 7861 291

Pepperl+Fuchs on dynaaminen ja tulevaisuuteen suuntaava yritys joka myy konepajateollisuuden, robotiikan ja teollisuusautomaation komponentteja. Tuotannon sujuvuus, tuotteiden korkea laatu ja niiden maailmanlaajuinen saatavuus ovat tuoneet yritykselle menestystä jo yli 70 vuoden ajan. Pepperl+Fuchs työllistää maailman laajuisesti yhteensä noin 6300 henkilöä. Globaalilla yrityksellä on tuotantolaitoksia Saksassa, Singaporessa, Yhdysvalloissa, Unkarissa, Indonesiassa ja Vietnamissa, joista suurin osa ovat ISO 9001-sertifioitu.