Redundancy Module PS1000-D2-24.20.RM

24 V DC to 28 V DC input
2 inputs with 1 output
Output 24 V DC, 20 A
Housing width 32 mm
Built-in decoupling mosfets for 1+1 and N+1 redundancy
Automatic load sharing
Reverse input polarity protection
Easy wiring: distribution terminal for negative pole included
Redundancy status indicator
Suitable for Zone 2/Div. 2 mounting

Technical Data
Details
Informative Literature
Product Documentation
Design / Simulation
Approvals
Associated Products

Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.

Lataa koko tietolomake PDF-tiedostona:

Ote tietolomakkeesta: Tekniset tiedot PS1000-D2-24.20.RM

Electrical specifications
Voltage drop		input to output 0.1 ... 0.5 V at input 2 x 5 A 0.2 ... 0.5 V at input 2 x 10 A 0.24 ... 0.5 V at input 2 x 12 A load share dependent
Power dissipation		1.7 W no load 2.6 ... 4.7 W at input 2 x 5 A 5.6 ... 8.7 W at input 2 x 10 A
Input
Rated voltage		24 ... 28 V
Voltage range		18 ... 35 V DC
Current		2 x 12 A at ambient temperature < 45 °C (113 °F) 2 x 10 A at ambient temperature 70 °C (158 °F) 2x 17 mA for max. 5 s for lower output currents see technical information
Output
Voltage range		24 ... 28 V DC
Current		24 A at ambient temperature < 45 °C (113 °F) 20 A at ambient temperature < 70 °C (158 °F) 32.5 A for max. 5 s max. 26 A in overload or short circuit mode (voltage < 6 V DC)
Fault indication output
Connection		terminals 13, 14 : relay contact load share terminals 23, 24 : relay contact redundancy
Output type		relay contact load share - contact is closed if the adjustment of the output voltages are sufficient - contact is open if an even load share does not occur and readjustment of the output voltage is required relay contact redundancy - contact is closed if no fault is detected - contact is open if one or both input voltages are below 22 V DC or above 30 V DC - contact is open if the output current is higher than the adjusted value of the output current - contact is open if an internal defect of the device is detected
Contact loading		max. 60 V DC/0.3 A ; 30 V DC/1 A ; 30 V AC/0.5 A resistive load min. 1 mA at 5 V DC
Galvanic isolation
Input/Output		SELV/PELV
Indicators/settings
Display elements		LED green: output status - LED lights up if the output current is smaller than the adjusted value of the output current LEDs green: load share status - LEDs indicate the load share status between the two power supplies LED green: redundancy status - LED lights up if no fault is detected - LED flashes if one ore both input values are below 22 V or above 30 V - LED flashes if the output current is higher than the adjusted value of the output current - LED flashes if an internal defect is detected
Control elements		rotary switch
Configuration		setting of the output current via rotary switch - switch setting to 5 A in combination with two 5A power supplies (1+1 redundancy) - switch setting to 10 A in combination with two 10A power supplies (1+1 redundancy) - switch setting to 20 A for N+1 redundant systems
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	IEC/EN 61000-6-1 , IEC/EN 61000-6-2 , IEC/EN 61000-6-3 , IEC/EN 61000-6-4
Low voltage
	Directive 2014/35/EU	EN 61010-1
RoHS
	Directive 2011/65/EU (RoHS)	IEC/EN 63000:2019
Conformity
Degree of protection		EN 60529
Shock resistance		EN 60068-2-27
Vibration resistance		EN 60068-2-6
Ambient conditions
Ambient temperature		-40 ... 70 °C (-40 ... 158 °F) , see technical information
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Relative humidity		5 ... 95 %, noncondensing
Shock resistance		20 g , 11 ms or 30 g , 6 ms
Vibration resistance		2 ... 17.8 Hz : ± 1.6 mm , 17.8 ... 500 Hz : 2 g
Mechanical specifications
Housing material		aluminum alloy , galvanized steel
Degree of protection		IP20
Connection
	Input/Output	screw terminals conductor cross section: max. 6 mm² (AWG 20-10) cable diameter: max. 2.8 mm, wire end ferrules included stripped insulation length: 7 mm tightening torque: max. 0.8 Nm
	Relay contact output	spring terminals conductor cross section: max. 1.5 mm² (AWG 24-16) cable diameter: max. 1.6 mm, wire end ferrules included stripped insulation length: 7 mm
Mass		approx. 310 g
Dimensions		32 x 124 x 117 mm (W x H x D) , without DIN mounting rail
	Height	124 mm
	Width	32 mm
	Depth	117 mm
Mounting		on 35 mm DIN mounting rail acc. to EN 60715:2001
Data for application in connection with hazardous areas
ATEX approval
	ATEX certificate	EPS 11 ATEX 1 312 X
	ATEX marking	II 3G Ex ec nC II T4 Gc
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2012+A11:2013 , EN 60079-7:2016 , EN 60079-15:2010
International approvals
UL approval		E223176
IECEx approval
	IECEx certificate	IECEx EPS 20.0057X
	IECEx marking	Ex ec nC IIC T4 Gc
	Standards	IEC 60079-0:2011 , IEC 60079-7:2015 , IEC 60079-15:2010
General information
Supplementary information		Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.

Classifications

System	Classcode
ECLASS 13.0	27040790
ECLASS 12.0	27040790
ECLASS 11.0	27040790
ECLASS 10.0.1	27040790
ECLASS 9.0	27040790
ECLASS 8.0	27049090
ECLASS 5.1	27049090
ETIM 9.0	EC002542
ETIM 8.0	EC002542
ETIM 7.0	EC002542
ETIM 6.0	EC002542
ETIM 5.0	EC002542
UNSPSC 12.1	39121004

Details: PS1000-D2-24.20.RM

Function

The device is a redundancy module for building redundant power supply systems.

The device is equipped with 2 inputs and 1 output. Power supplies with an output current of up to 24 A and one output can be connected to the inputs. The power supplies can transmit a rated current of up to 20 A.

The both inputs are decoupled by MOSFETs. This reduces heat generation and voltage drop between input and output.

The device is mounted on a 35 mm DIN mounting rail according to EN 60715.

Informative Literature: PS1000-D2-24.20.RM

Literature	Kieli	Tiedostotyyppi	Tiedoston koko
Product Information - PS1000 for Global Use up to Zone 2/Div. 2	ENG	PDF	577 KB

Product Documentation: PS1000-D2-24.20.RM

Product information	Kieli	Tiedostotyyppi	Tiedoston koko
Technical information	ENG	PDF	3796 KB
Safety and Security Documentation
Instruction manual / Betriebsanleitung	ALL	PDF	225 KB
Instruction manual / Betriebsanleitung	ALL	PDF	294 KB

Design / Simulation: PS1000-D2-24.20.RM

CAD	Kieli	Tiedostotyyppi	Tiedoston koko
CAD 3-D / CAD 3-D	ALL	STP	4884 KB
CAD Portal / CAD Portal	ALL	LINK	---
CAE
CAE EPLAN macro EDZ / CAE EPLAN Makro EDZ	ALL	EDZ	200 KB

Approvals: PS1000-D2-24.20.RM

Certificates	Sertifikaatin nro	Kieli	Tiedostotyyppi	Tiedoston koko
Bureau Veritas IECEx Certificate of Conformity	IECEx EPS 20.0057X	ALL	LINK	---
Canada, USA CSA Hazardous Location	CoC 80059967	ALL	PDF	84 KB
China SITIIAS CCC Ex Certificate	2023122303116293 (Mannheim)	ALL	PDF	519 KB
Europe Bureau Veritas ATEX Category 3 G	EPS 11 ATEX 1 312X	ALL	PDF	1011 KB
US CA UL	CoC E223176 RptRef E223176-20070416	ALL	PDF	444 KB
Declaration of Conformity
EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F)	DOC-4793	ALL	PDF	73 KB
EU Declaration of Conformity (P+F)	TDOC-4793AFIN	FIN	PDF	182 KB

Liitännäistuotteet: PS1000-D2-24.20.RM

Accessory of

	PS1000-A6-24.10 Power Supply
	100 V AC to 240 V AC wide-range input, Output 24 V DC, 10 A, 240 W, 1-phase, Housing width 39 mm, Efficiency up to 95.2 %, Minimal inrush current surge, DC OK relay contact, Suitable for Zone 2/Div. 2 mounting, Device type: device for DIN rail mounting, Function: Standard, Rated voltage: 24 V DC, Voltage range: 24 ... 28 V DC factory setting: 24.1 Vpa

	PS1000-A6-24.5 Power Supply
	100 V AC to 240 V AC wide-range input, Output 24 V DC, 5 A, 120 W, 1-phase, Housing width 32 mm, Efficiency up to 94.3 %, Minimal inrush current surge, DC OK relay contact, Suitable for Zone 2/Div. 2 mounting, Device type: device for DIN rail mounting, Function: Standard, Rated voltage: 24 V DC, Voltage range: 24 ... 28 V DC factory setting: 24.1 Vpa

General Notes Relating to Pepperl+Fuchs Product Information

Pikalinkit

Pepperl+Fuchs Oy
Areenakatu 7
FI-37570 Lempäälä
Finland
info@fi.pepperl-fuchs.com
phone +358 20 7861 290
info@fi.pepperl-fuchs.com
phone +358 20 7861 291

Pepperl+Fuchs on dynaaminen ja tulevaisuuteen suuntaava yritys joka myy konepajateollisuuden, robotiikan ja teollisuusautomaation komponentteja. Tuotannon sujuvuus, tuotteiden korkea laatu ja niiden maailmanlaajuinen saatavuus ovat tuoneet yritykselle menestystä jo yli 70 vuoden ajan. Pepperl+Fuchs työllistää maailman laajuisesti yhteensä noin 6300 henkilöä. Globaalilla yrityksellä on tuotantolaitoksia Saksassa, Singaporessa, Yhdysvalloissa, Unkarissa, Indonesiassa ja Vietnamissa, joista suurin osa ovat ISO 9001-sertifioitu.