Switch Amplifier HiC2831

1-channel isolated barrier
24 V DC supply (bus powered)
Dry contact or NAMUR input
Usable as signal splitter (1 input and 2 outputs)
2 passive transistor outputs (resistive acc. to EN 60947-5-6)
Line fault transparency (LFT)
Up to SIL 2 acc. to IEC 61508

Technical Data
Product Documentation
Design / Simulation
Approvals

Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.

Lataa koko tietolomake PDF-tiedostona:

Ote tietolomakkeesta: Tekniset tiedot HiC2831

General specifications
Signal type		Digital Input
Supply
Connection		SL1: 1a(-), 1b(-); 2a(+), 2b(+)
Rated voltage		19 ... 30 V DC via Termination Board
Ripple		≤ 10 %
Rated current		≤ 25 mA
Power dissipation		≤ 500 mW
Power consumption		≤ 600 mW
Input
Connection		SL2: 5a(+), 5b(-)
Rated values		acc. to EN 60947-5-6 (NAMUR), see manual for electrical data
Open circuit voltage/short-circuit current		approx. 10 V DC / approx. 8 mA
Switching point/switching hysteresis		1.2 ... 2.1 mA / approx. 0.2 mA
Line fault detection		breakage I ≤ 0.1 mA , short-circuit I ≥ 6.5 mA
Pulse/Pause ratio		min. 100 µs / min. 100 µs
Output
Connection		SL1: 8a(+), 7a(-); 10a(+), 9a(-)
Rated voltage		8 V DC
Response time		≤ 200 µs
Output I, II		signal or fault message, passive transistor output (resistive) 0-signal: 14 kΩ ± 10 % 1-signal: 1.8 kΩ ± 10 % fault: > 100 kΩ
Fault indication output
Connection		SL1: 6b
Output type		open collector transistor (internal fault bus)
Transfer characteristics
Switching frequency		≤ 5 kHz
Galvanic isolation
Output/power supply		basic insulation according to IEC/EN 61010-1, rated insulation voltage 60 V_eff
Output/Output		basic insulation according to IEC/EN 61010-1, rated insulation voltage 60 V_eff
Indicators/settings
Display elements		LED PWR ON (power supply), one green LED LED STATUS (output status), one bicolored LED (yellow) LED FAULT (lead fault), one bicolored LED (red)
Control elements		DIP switches at the housing side for: - mode of operation input - output - lead fault detection enable/disable
Labeling		space for labeling at the front
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2013 (industrial locations)
Conformity
Electromagnetic compatibility		NE 21:2012 , EN 61326-3-2:2008
Degree of protection		IEC 60529:2001
Protection against electrical shock		IEC 61010-1
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Mechanical specifications
Degree of protection		IP20
Mass		approx. 100 g
Dimensions		12.5 x 106 x 128 mm (0.5 x 4.2 x 5.1 inch)
	Height	128 mm
	Width	12.5 mm
	Length	106 mm
Mounting		on termination board
Coding		pin 1 and 2 trimmed For further information see system description.
Data for application in connection with hazardous areas
EU-type examination certificate		BVS 11 ATEX E 026
	Marking	II (1) G [Ex ia] IIC, II (1) D [Ex ia] IIIC I (M1) [Ex ia] I
	Input	Ex ia
	Voltage	10.5 V
	Current	17.1 mA
	Power	45 mW (linear characteristic)
Supply
	Maximum safe voltage	253 V AC (Attention! U_m is no rated voltage.)
Output
	Maximum safe voltage	253 V AC (Attention! U_m is no rated voltage.)
Certificate		KIWA 15 ATEX 0037 X
	Marking	II 3G Ex nA IIC T4 Gc
Galvanic isolation
	Input/Output	safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
	Input/power supply	safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2012+A11:2013 , EN 60079-11:2012 , EN 60079-15:2010 , EN 50303:2000
International approvals
UL approval
	Control drawing	116-0331
IECEx approval		IECEx BVS 11.0040
	Approved for	[Ex ia Ga] IIC, [Ex ia] IIIC , [Ex ia] I
General information
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.

Classifications

System	Classcode
ECLASS 13.0	27210121
ECLASS 12.0	27210121
ECLASS 11.0	27210121
ECLASS 10.0.1	27210121
ECLASS 9.0	27210121
ECLASS 8.0	27210121
ECLASS 5.1	27210121
ETIM 9.0	EC001485
ETIM 8.0	EC001485
ETIM 7.0	EC001485
ETIM 6.0	EC001485
ETIM 5.0	EC001485
UNSPSC 12.1	32101514

Details: HiC2831

Product Documentation: HiC2831

Safety and Security Documentation	Kieli	Tiedostotyyppi	Tiedoston koko
Käyttöohje	FIN	PDF	158 KB
Functional Safety Manual	ENG	PDF	2014 KB
Manuals
System Manual	ENG	PDF	5438 KB

Design / Simulation: HiC2831

CAD	Kieli	Tiedostotyyppi	Tiedoston koko
CAD 2-D / CAD 2-D	ALL	ZIP	16364 KB

Approvals: HiC2831

Certificates	Sertifikaatin nro	Kieli	Tiedostotyyppi	Tiedoston koko
Brasil TUV Rheinland Brazil	TÜV 16.0821	ALL	PDF	1136 KB
Europe KIWA ATEX Category 3 G	KIWA 15 ATEX 0037X	ALL	PDF	988 KB
KIWA IECEx Certificate of Conformity Zone 2	IECEx KIWA 15.0019X	ALL	LINK	---
Korea KOSHA	15-AV4BO-0596	ALL	PDF	611 KB
Control Drawings
Control drawing UL / Control drawing UL		ALL	PDF	136 KB

General Notes Relating to Pepperl+Fuchs Product Information

Pikalinkit

Selector for Safety Products

Choose from various selection criteria like safety integrity level, performance level, device function, and signal type and find the SIL/PL assessed device that you are looking for.

Pepperl+Fuchs Oy
Areenakatu 7
FI-37570 Lempäälä
Finland
info@fi.pepperl-fuchs.com
phone +358 20 7861 290
info@fi.pepperl-fuchs.com
phone +358 20 7861 291

Pepperl+Fuchs on dynaaminen ja tulevaisuuteen suuntaava yritys joka myy konepajateollisuuden, robotiikan ja teollisuusautomaation komponentteja. Tuotannon sujuvuus, tuotteiden korkea laatu ja niiden maailmanlaajuinen saatavuus ovat tuoneet yritykselle menestystä jo yli 70 vuoden ajan. Pepperl+Fuchs työllistää maailman laajuisesti yhteensä noin 6300 henkilöä. Globaalilla yrityksellä on tuotantolaitoksia Saksassa, Singaporessa, Yhdysvalloissa, Unkarissa, Indonesiassa ja Vietnamissa, joista suurin osa ovat ISO 9001-sertifioitu.