Termination Board HiCTB16-TRI-DIISS-EL-PL

System board for Schneider Electric, Tricon series by Triconex
TAN48 approval
For 32-channel (16+16) DI card 3503E
For 16 modules
Recommended module: HiC2821 (DI)
24 V DC supply
Line fault detection (LFD)
Hazardous area: pluggable screw terminals, blue
Non-hazardous area: ELCO socket, 56-pin

Technical Data
Details
Product Documentation
Design / Simulation
Approvals
Associated Products

Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.

Lataa koko tietolomake PDF-tiedostona:

Ote tietolomakkeesta: Tekniset tiedot HiCTB16-TRI-DIISS-EL-PL

Supply
Connection		X20: terminals 3, 5(+); 4, 6(-)
Nominal voltage		24 V DC , in consideration of rated voltage of used isolators
Voltage drop		0.9 V , voltage drop across the series diode on the termination board must be considered
Ripple		≤ 10 %
Fusing		4 A , in each case for 16 modules
Power dissipation		≤ 500 mW , without modules
Reverse polarity protection		yes
Redundancy
Supply		Redundancy available. The supply for the isolators is decoupled, monitored and fused.
Fault indication output
Connection		fault bus (Fault) : X20: terminals 1, 2 fault indication output (LFD) : X3: terminals 1, 2
Output type		volt-free contact
Switch behaviour		fault bus (Fault) - no fault: relay contact of the fault indication board closed - power supply fault: relay contact of the fault indication board open - module fault: relay contact of the fault indication board open fault indication output (LFD) - no fault: relay contact closed - module fault: relay contact open
Contact loading		fault bus (Fault) : 30 V DC , 1 A , see fault indication board fault indication output (LFD) : see datasheet of isolated barrier
Indicators/settings
Display elements		LED PWR1 (termination board power supply), green LED LED PWR2 (termination board power supply), green LED
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2013 (industrial locations)
Conformity
Electromagnetic compatibility		NE 21:2017 For further information see system description.
Degree of protection		IEC 60529:2001
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-40 ... 70 °C (-40 ... 158 °F)
Mechanical specifications
Degree of protection		IP20
Connection
	Field side	explosion hazardous area: pluggable screw terminals , blue
	Control side	non-explosion hazardous area: ELCO socket, 56-pin
	Supply	pluggable screw terminals , black
	Fault output	pluggable screw terminals , black
Core cross section		screw terminals: 0.2 ... 2.5 mm² (24 ... 12 AWG)
Material		housing: polycarbonate, 10 % glass fiber reinforced
Mass		approx. 785 g
Dimensions		216 x 200 x 163 mm (8.5 x 7.9 x 6.42 inch) (W x H x D) , depth including module assembly
	Height	200 mm
	Width	216 mm
	Depth	163 mm
Mounting		on 35 mm DIN mounting rail acc. to EN 60715:2001
Data for application in connection with hazardous areas
EU-type examination certificate		CESI 06 ATEX 022
	Marking	II (1)G [Ex ia Ga] IIC II (1)D [Ex ia Da] IIIC I (M1) [Ex ia Ma] I
Non-hazardous area
	Maximum safe voltage	250 V (Attention! U_m is no rated voltage.)
Galvanic isolation
	Field circuit/control circuit	safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN IEC 60079-0:2018+AC:2020 , EN 60079-11:2012 , EN 50303:2000
International approvals
UL approval		E106378
	Control drawing	116-0327
IECEx approval
	IECEx certificate	IECEx CES 06.0003
	IECEx marking	[Ex ia Ga] IIC [Ex ia Da] IIIC [Ex ia Ma] I
General information
Supplementary information		Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.

Classifications

System	Classcode
ECLASS 13.0	27210121
ECLASS 12.0	27210121
ECLASS 11.0	27210121
ECLASS 10.0.1	27210121
ECLASS 9.0	27210121
ECLASS 8.0	27210121
ECLASS 5.1	27210121
ETIM 9.0	EC001485
ETIM 8.0	EC001485
ETIM 7.0	EC001485
ETIM 6.0	EC001485
ETIM 5.0	EC001485
UNSPSC 12.1	39121008

Details: HiCTB16-TRI-DIISS-EL-PL

Function

The function of the termination board and the connector pinout is exactly fitted to the requirements of Triconex system.

The termination board has a fault bus (Fault) that is available at the redundant terminals. Power supply faults and module faults are indicated via this fault bus. The fault signals of several termination boards can be connected together and can be monitored by an optional fault indication board. The fault signals are then available to the control system as a volt-free contact.

In addition, the termination board has a fault indication output (LFD), which will be used to indicate module faults as a volt-free contact. These fault signals can also be output via this fault indication output without a separate fault indication board. This assumes that the termination board is fully equipped and the isolators are configured for this function.

The termination board is supplied with a robust plastic housing. This design permits the fast and reliable installation on 35 mm DIN mounting rail according to EN 60715 in the switch cabinet.

Product Documentation: HiCTB16-TRI-DIISS-EL-PL

Product information	Kieli	Tiedostotyyppi	Tiedoston koko
Pinout Table	ENG	PDF	83 KB
Brief Instructions
Brief instructions	ENG	PDF	3356 KB
Safety and Security Documentation
Käyttöohje	FIN	PDF	153 KB
Manuals
System Manual	ENG	PDF	5438 KB

Design / Simulation: HiCTB16-TRI-DIISS-EL-PL

CAD	Kieli	Tiedostotyyppi	Tiedoston koko
CAD 2-D / CAD 2-D	ALL	ZIP	16364 KB

Approvals: HiCTB16-TRI-DIISS-EL-PL

Certificates	Sertifikaatin nro	Kieli	Tiedostotyyppi	Tiedoston koko
Brasil TUV Rheinland Brazil	TÜV 14.0084 X	ALL	PDF	1194 KB
CESI IECEx Certificate of Conformity	IECEx CES 06.0003	ALL	LINK	---
China SITIIAS CCC Ex Certificate	2021322308004238 (Singapore)	ALL	PDF	1842 KB
Europe CESI ATEX Category (1) GD ATEX Category (M1)	CESI 06 ATEX 022	ALL	PDF	869 KB
India PESO (India) CCOE	A/P/HQ/KA/104/5881 (P508977)	ALL	PDF	100 KB
South Africa MASC	MASC MS/17-0855	ALL	PDF	869 KB
USA Canada UL Hazardous Location Certificate of Compliance cULus UL E106378	CoC E106378 RepRef E106378-20100930	ALL	PDF	478 KB
Declaration of Conformity
EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F)	DOC-0632E	ALL	PDF	50 KB

Liitännäistuotteet: HiCTB16-TRI-DIISS-EL-PL

Accessories

	HiALC-HiCTB-SET-108 Label Carrier
	For HiC Termination Boards, 1 piece for 8-position Termination Board, 2 pieces for 16-position Termination Boardpa

	HiATB01-FAULT-01 Fault Indication Board
	1-channel, 24 V DC supply, Monitors up to 16 HiC Termination Boards, Relay contact output, LEDs for supply and fault statuspa

	HiC2821 Switch Amplifier
	1-channel isolated barrier, 24 V DC supply (bus powered), Dry contact or NAMUR input, Usable as signal splitter (1 input and 2 outputs), 2 relay contact outputs, Fault relay contact output, Line fault detection (LFD), Reversible mode of operation, Up to SIL 2 acc. to IEC/EN 61508, Housing width: 12.5 mm, Number of channels: 1-channel, Safety Integrity Level (SIL): SIL 2, Rated voltage: 19 ... 30 V DC bus powered via Termination Board, Field device: NAMUR sensor, Field device [2]: volt-free contactpa

General Notes Relating to Pepperl+Fuchs Product Information

Pikalinkit

Pepperl+Fuchs Oy
Areenakatu 7
FI-37570 Lempäälä
Finland
info@fi.pepperl-fuchs.com
phone +358 20 7861 290
info@fi.pepperl-fuchs.com
phone +358 20 7861 291

Pepperl+Fuchs on dynaaminen ja tulevaisuuteen suuntaava yritys joka myy konepajateollisuuden, robotiikan ja teollisuusautomaation komponentteja. Tuotannon sujuvuus, tuotteiden korkea laatu ja niiden maailmanlaajuinen saatavuus ovat tuoneet yritykselle menestystä jo yli 70 vuoden ajan. Pepperl+Fuchs työllistää maailman laajuisesti yhteensä noin 6300 henkilöä. Globaalilla yrityksellä on tuotantolaitoksia Saksassa, Singaporessa, Yhdysvalloissa, Unkarissa, Indonesiassa ja Vietnamissa, joista suurin osa ovat ISO 9001-sertifioitu.