Digital Input LB1008A

8-channel
Dry contact or NAMUR inputs
Installation in Zone 2 or safe area
Positive or negative logic selectable
Simulation mode for service operations (forcing)
Line fault detection (LFD)
Permanently self-monitoring
Module can be exchanged under voltage

Technical Data
Informative Literature
Product Documentation
Design / Simulation
Approvals

Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.

Téléchargez ici la fiche technique complète en PDF:

Caractéristiques techniques LB1008A

Slots
Occupied slots		2
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power dissipation		0.95 W
Power consumption		0.95 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Digital input
Number of channels		8
Sensor interface
	Connection	NAMUR sensor
	Connection [2]	volt-free contact
	Connection [3]	Usage without connection to areas where there is a risk of explosion: active signals, mechanical contacts, NAMUR sensors, 2-wire sensors If the device has been operated in general electrical systems that are not connected to areas where there is a risk of explosion, the device cannot then be used in electrical systems that are connected to areas where there is a risk of explosion. Usage with connection to areas where there is a risk of explosion: mechanical contacts, NAMUR sensors
Connection		channel I: 1+, 2-; channel II: 3+, 4-; channel III: 5+, 6-; channel IV: 7+, 8-; channel V: 9+, 10-; channel VI: 11+, 12-; channel VII: 13+, 14-; channel VIII: 15+, 16-
Rated values		acc. to EN 60947-5-6 (NAMUR)
Switching point/switching hysteresis		1.2 ... 2.1 mA / ± 0.2 mA
Voltage		8.2 V
Internal resistor		1 kΩ
Line fault detection		can be switched on/off for each channel via configuration tool , active signals (24 V, 5 V) without line fault detection
	Connection	mechanical switch with additional resistors (see connection diagram) proximity sensors without additional wiring
	Short-circuit	< 360 Ω
	Open-circuit	< 0.35 mA
Digital signals (active)		Use in safe area: configurable 24 V 5 V
	Switching point: ON	> 8 V > 2.7 V
	Switching point: OFF	< 3 V < 2.3 V
Minimum pulse duration		1 ms
Indicators/settings
LED indication		Power LED (P) green: supply Status LED (I) red: line fault
Coding		optional mechanical coding via front socket
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2013
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Environmental test		EN 60068-2-14
Shock resistance		EN 60068-2-27
Vibration resistance		EN 60068-2-6
Damaging gas		EN 60068-2-42
Relative humidity		EN 60068-2-78
Ambient conditions
Ambient temperature		-40 ... 60 °C (-40 ... 140 °F) , 70 °C (non-Ex)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Relative humidity		95 % non-condensing
Altitude		max. 2000 m
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz; transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g; 10 cycles frequency range 5 ... 100 Hz; transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g; 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 130 g
Dimensions		32.5 x 100 x 102 mm (1.28 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
Certificate		PF 08 CERT 1234 X
	Marking	II 3 G Ex nA [ic] IIC T4 Gc
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN IEC 60079-0:2018+AC:2020 EN 60079-11:2012 EN 60079-15:2010
International approvals
IECEx approval
	IECEx certificate	IECEx BVS 09.0037X
	IECEx marking	Ex nA [ic] IIC T4 Gc
General information
System information		The module has to be mounted in appropriate backplanes (LB9***) in Zone 2 or outside hazardous areas. Here, observe the corresponding declaration of conformity. For use in hazardous areas (e. g. Zone 2 or Zone 22) the module must be installed in an appropriate enclosure.
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.

Classifications

System	Classcode
ECLASS 13.0	27210121
ECLASS 12.0	27210121
ECLASS 11.0	27210121
ECLASS 10.0.1	27210121
ECLASS 9.0	27210121
ECLASS 8.0	27210121
ECLASS 5.1	27210120
ETIM 9.0	EC001485
ETIM 8.0	EC001485
ETIM 7.0	EC001485
ETIM 6.0	EC001485
ETIM 5.0	EC001485
UNSPSC 12.1	39121008

Details: LB1008A

Informative Literature: LB1008A

Literature	Langue	Type de fichier	Taille
Application Report - Communication Redundancy for Uninterrupted Operation	ENG	PDF	529 KB
Application Report - LB and FB Remote I/O Systems for Digitally Connecting Analog Field Devices	ENG	PDF	208 KB
Application Report - Space Saving Extension for Existing Plants	ENG	PDF	300 KB
Application Report - The Modern Whiskey Distillery	ENG	PDF	176 KB
Application Report - Use of Remote I/O in Fluidized Bed Systems	ENG	PDF	222 KB
Application Report - Using Remote I/O Systems for the Efficient Digitalization of Plants	ENG	PDF	371 KB

Product Documentation: LB1008A

Safety and Security Documentation	Langue	Type de fichier	Taille
Manuel d'instructions	FRA	PDF	175 KB
Manuals
Hardware Manual LB-Remote-I/O-System	ENG	PDF	5385 KB

Design / Simulation: LB1008A

CAD	Langue	Type de fichier	Taille
CAD 3-D / CAD 3-D	ALL	STP	3673 KB
CAD Portal / CAD Portal	ALL	LINK	---
CAE
CAE EPLAN Data Portal / CAE EPLAN Data Portal	ALL	LINK	---
CAE EPLAN macro EDZ / CAE EPLAN Makro EDZ	ALL	EDZ	169 KB
EPLAN macros LB-System / EPLAN-Makros LB-System	ALL	ZIP	65808 KB

Approvals: LB1008A

Certificates	Identification	Langue	Type de fichier	Taille
Bureau Veritas (Maritime) Marine	22449/C0 BV	ALL	PDF	590 KB
China SITIIAS CCC Ex Certificate	2021322310003600 (Singapore)	ALL	PDF	11357 KB
DEKRA EXAM IECEx Certificate of Conformity	IECEx BVS 09.0037X	ALL	LINK	---
DNV Marine	TAA0000034	ALL	PDF	110 KB
Europe Pepperl+Fuchs ATEX Category 3 G Certificate of Conformity	PF 08 CERT 1234 X	ALL	PDF	1503 KB
Lloyd's Register Marine	LR2003616TA-02	ALL	PDF	557 KB
South Africa MASC	MASC MS/20-8438X	ALL	PDF	730 KB
Declaration of Conformity
EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F)	DOC-1062F	ALL	PDF	1041 KB
UK Declaration of Conformity (P+F) / UK-Konformitäterklärung (P+F)	DOC-5374	ALL	PDF	1038 KB

Remarques générales sur les informations produit de Pepperl+Fuchs

Accès direct

Une passerelle vers l'Industrie 4.0

Certifiée Zone 2 et Classe I/Div. 2, la nouvelle passerelle PROFINET d'E/S déportées de Pepperl+Fuchs ouvre la voie à des applications de l'Industrie 4.0 dans les industries de transformation.

Pepperl+Fuchs North Africa
Abraj Abdelmoumen B2
Boulevard Abdelmoumen
20340 Casablanca
Morocco
ventes.afrique@de.pepperl-fuchs.com
phone +212 (0) 522 25 97 90

Pepperl+Fuchs est leader comme concepteur et fabricant de capteurs et composants électroniques pour le marché mondial de l'automatisation. L'innovation constante, la qualité incontestable et la croissance soutenue, garantissent notre succès, depuis plus de 70 ans. Pepperl+Fuchs emploie 6300 personnes dans le monde et compte des usines en Allemagne, aux USA, à Singapour, en Hongrie, en Indonésie et au Vietnam ; la plupart d'entre elles sont certifiées ISO 9001.