Digital Output with Shutdown Input FB6216E3

2-channel
Outputs Ex ia
Installation in suitable enclosures in Zone 1
Module can be exchanged under voltage (hot swap)
Line fault detection (LFD)
Positive or negative logic selectable
Simulation mode for service operations (forcing)
Permanently self-monitoring
Output with watchdog
Output with bus-independent safety shutdown input

Technical Data
Informative Literature
Product Documentation
Design / Simulation
Approvals

Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.

Téléchargez ici la fiche technique complète en PDF:

Caractéristiques techniques FB6216E3

Supply
Connection		backplane bus / booster terminals
Rated voltage		12 V DC , only in connection with the power supplies FB92**
Power dissipation		1.95 W
Power consumption		2.9 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Digital output
Number of channels		2
Suitable field devices
	Field device	Solenoid Valve
	Field device [2]	audible alarm
	Field device [3]	visual alarm
Connection		channel I: 1+, 4/5/6/8-; channel II: 7+, 4/5/6/8-
Internal resistor		258 Ω , both channels parallel 129 Ω
Current limit		40 mA both channels parallel 80 mA
Open loop voltage		23 V , both channels parallel 23 V
Line fault detection		can be switched on/off for each channel via configuration tool also when turned off (every 2.5 s the valve is turned on for 2 ms)
	Short-circuit	< 50 Ω
	Open-circuit	> 10 kΩ
Response time		10 ms (depending on bus cycle time)
Watchdog		within 0.5 s the device goes in safe state, e.g. after loss of communication
Indicators/settings
LED indication		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1, 2) red: line fault (lead breakage or short circuit) , yellow: state of digital I/O (0/1) Mode LED (M) white: Parallel operation of outputs
Coding		optional mechanical coding via front socket
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2013
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Environmental test		EN 60068-2-14
Shock resistance		EN 60068-2-27
Vibration resistance		EN 60068-2-6
Damaging gas		EN 60068-2-42
Relative humidity		EN 60068-2-78
Ambient conditions
Ambient temperature		-40 ... 60 °C (-40 ... 140 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Relative humidity		95 % non-condensing
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz; transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g; 10 cycles frequency range 5 ... 100 Hz; transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g; 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 (module) , a separate housing is required acc. to the system description
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 425 g
Dimensions		28 x 107 x 132 mm (1.1 x 4.2 x 5.2 inch)
Data for application in connection with hazardous areas
EU-type examination certificate		Presafe 19 ATEX 14054U
	Marking	II 2(1)G Ex db eb q [ia Ga] IIC Gb II (1)D [Ex ia Da] IIIC I (M1) [Ex ia Ma] I
Output
	Voltage	24.2 V
	Current	108 mA
	Power	654 mW
	Internal capacitance	12 nF
	Internal inductance	0 mH
Output (both channels parallel)
	Voltage	24.2 V
	Current	216 mA
	Power	1308 mW
	Internal capacitance	24 nF
	Internal inductance	0 mH
Galvanic isolation
	Output/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2018+AC:2020 EN 60079-1:2014 EN 60079-5:2015 EN 60079-7:2015+A1:2018 EN 60079-11:2012
International approvals
ATEX approval		Presafe 19 ATEX 14054U
IECEx approval		IECEx PRE 19.0009U
	Approved for	Ex db eb q [ia Ga] IIC Gb [Ex ia Da] IIIC [Ex ia Ma] I
General information
System information		The module has to be mounted in appropriate backplanes and housings (FB92**) in Zone 1, 2, 21, 22 or outside hazardous areas (gas or dust). Here, observe the corresponding EC-type examination certificate.
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.

Classifications

System	Classcode
ECLASS 13.0	27210101
ECLASS 12.0	27210101
ECLASS 11.0	27210101
ECLASS 10.0.1	27210101
ECLASS 9.0	27210101
ECLASS 8.0	27210101
ECLASS 5.1	27210120
ETIM 9.0	EC001485
ETIM 8.0	EC001485
ETIM 7.0	EC001485
ETIM 6.0	EC001485
ETIM 5.0	EC001485
UNSPSC 12.1	39121008

Details: FB6216E3

Informative Literature: FB6216E3

Literature	Langue	Type de fichier	Taille
Application Report - Communication Redundancy for Uninterrupted Operation	ENG	PDF	529 KB
Application Report - LB and FB Remote I/O Systems for Digitally Connecting Analog Field Devices	ENG	PDF	208 KB
Application Report - Space Saving Extension for Existing Plants	ENG	PDF	300 KB
Application Report - Using Remote I/O Systems for the Efficient Digitalization of Plants	ENG	PDF	371 KB
Selection table - Solenoid driver/valve combinations	ENG	PDF	299 KB

Product Documentation: FB6216E3

Safety and Security Documentation	Langue	Type de fichier	Taille
Manuel d'instructions	FRA	PDF	182 KB
Functional Safety Manual	ENG	PDF	2364 KB
Manuals
Hardware Manual FB-Remote-I/O-System	ENG	PDF	9157 KB

Design / Simulation: FB6216E3

CAD	Langue	Type de fichier	Taille
CAD 3-D / CAD 3-D	ALL	STP	4752 KB
CAD Portal / CAD Portal	ALL	LINK	---
CAE
CAE EPLAN Data Portal / CAE EPLAN Data Portal	ALL	LINK	---
EPLAN macro EDZ / EPLAN Makro EDZ	ALL	EDZ	940 KB

Approvals: FB6216E3

Certificates	Identification	Langue	Type de fichier	Taille
Brasil TUV Rheinland Brazil	TÜV 19.0476 U	ALL	PDF	1201 KB
China SITIIAS CCC Ex Certificate	2021322310004114 (Mannheim)	ALL	PDF	2172 KB
Europe Presafe DNV GL ATEX Category (1) D ATEX Category 2 (1) ATEX Category (M1)	Presafe 19 ATEX 14054U	ALL	PDF	257 KB
Korea KOSHA	20-AV4BO-0408U	ALL	PDF	836 KB
Korea KOSHA	20-AV4BO-0401U	ALL	PDF	823 KB
Presafe DNV GL IECEx Certificate of Conformity	IECEx PRE 19.0009U	ALL	LINK	---
United Kingdom CML UK-Type Examination Certificate UKEX Category (1) D UKEX Category (1) G UKEX Category (M1)	CML 23UKEX2150U	ALL	PDF	180 KB
Declaration of Conformity
EU Declaration of Conformity (P+F)	TDOC-4259BFRA	FRA	PDF	1140 KB
UK Declaration of Conformity (P+F)	TDOC-6773_ENG	ENG	PDF	1110 KB

Remarques générales sur les informations produit de Pepperl+Fuchs

Accès direct

Pepperl+Fuchs North Africa
Abraj Abdelmoumen B2
Boulevard Abdelmoumen
20340 Casablanca
Morocco
ventes.afrique@de.pepperl-fuchs.com
phone +212 (0) 522 25 97 90

Pepperl+Fuchs est leader comme concepteur et fabricant de capteurs et composants électroniques pour le marché mondial de l'automatisation. L'innovation constante, la qualité incontestable et la croissance soutenue, garantissent notre succès, depuis plus de 70 ans. Pepperl+Fuchs emploie 6300 personnes dans le monde et compte des usines en Allemagne, aux USA, à Singapour, en Hongrie, en Indonésie et au Vietnam ; la plupart d'entre elles sont certifiées ISO 9001.