Float Switch LFL2-BK-U-PUR10-EMS
- Switch element: microswitch, mercury-free
- Limit value detection for fluids
- Ball design: high buoyancy
Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.
Téléchargez ici la fiche technique complète en PDF ::
Caractéristiques techniques LFL2-BK-U-PUR10-EMS
| Electrical specifications | ||
|---|---|---|
| Contact loading | 250 V AC/3 A; 150 V DC/0.25 A resistive load; 60 V DC/1 A resistive load | |
| Rated insulation voltage | 300 V | |
| Pulse withstand voltage | 4 kV | |
| Electrical life | ≥ 5 x 104 switching cycles | |
| Directive conformity | ||
| Low voltage | ||
| Directive 2014/35/EU | EN 60947-5-1:2004 + Cor.:2005 + A1:2009 | |
| Conformity | ||
| Degree of protection | IEC 60529:2001 | |
| Application | ||
| Description | microswitch with switching ball, change-over contact | |
| Function and system design | ||
| Equipment architecture | This device may be used with any sequential circuit, as long as the circuit can support the electrical circuit values of the switching elements. | |
| Operating conditions | ||
| Installation conditions | ||
| Installation instructions | range of application and minimum length between mounting and float: ≥ 100 mm (4 inch), preferred for fuels, heating oils, oily fluids mounting: The float switch is mounted by means of a counter weight or rods (e. g. float switch combination) from the top. The pivot of the cable should always be horizontal. |
|
| Process conditions | ||
| Process pressure (static pressure) | ≤ 2 bar (29 psi) at 20 °C (68 °F) | |
| Density | ≥ 0.6 g/cm3 | |
| Ambient conditions | ||
| Ambient temperature | 5 ... 70 °C (41 ... 158 °F) | |
| Storage temperature | -25 ... 70 °C (-13 ... 158 °F) | |
| Altitude | ≤ 2000 m above MSL | |
| Mechanical specifications | ||
| Degree of protection | IP68 | |
| Cable | ||
| Length | 10 m | |
| Mechanical construction | ||
| Material | float: PP (Polypropylene) cable: PUR, highly flexible (3 x 0.50 mm2) |
|
| Switching point | switch angle, measured against the horizontal: - upper switch point +25° ±10° - lower switch point -14° ±10° |
|
| General information | ||
| Supplementary information | Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com. | |
Classifications
| System | Classcode |
|---|---|
| ECLASS 13.0 | 27200510 |
| ECLASS 12.0 | 27200510 |
| ECLASS 11.0 | 27200510 |
| ECLASS 10.0.1 | 27200510 |
| ECLASS 9.0 | 27200510 |
| ECLASS 8.0 | 27200510 |
| ECLASS 5.1 | 27200510 |
| ETIM 9.0 | EC011178 |
| ETIM 8.0 | EC011178 |
| ETIM 7.0 | EC011178 |
| ETIM 6.0 | EC001447 |
| ETIM 5.0 | EC001447 |
| UNSPSC 12.1 | 41111950 |
Details: LFL2-BK-U-PUR10-EMS
Fonction
Le micro-interrupteur (contact inverseur) est intégré à un flotteur en PP et s'active en cas de déviation de sa position horizontale. La bille de commutation dans le flotteur bouge selon un axe et active le micro-interrupteur.
Product Documentation: LFL2-BK-U-PUR10-EMS
| Safety and Security Documentation | Langue | Type de fichier | Taille |
|---|---|---|---|
| Manuel d'instructions | FRA | 58 KB |
Design / Simulation: LFL2-BK-U-PUR10-EMS
| CAD | Langue | Type de fichier | Taille |
|---|---|---|---|
| CAD 3-D / CAD 3-D | ALL | STP | 482 KB |
| CAD Portal / CAD Portal | ALL | LINK | --- |
Approvals: LFL2-BK-U-PUR10-EMS
| Declaration of Conformity | Identification | Langue | Type de fichier | Taille |
|---|---|---|---|---|
| EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F) | DOC-1832D | ALL | 1231 KB | |
| UK Declaration of Conformity (P+F) | TDOC-5954_ENG | ENG | 1285 KB | |
| Contamination Declaration | ||||
| Contamination declaration / Kontaminationserklärung | ALL | 137 KB | ||
Produits associés : LFL2-BK-U-PUR10-EMS
| Accessories | ||||||
|---|---|---|---|---|---|---|
|
||||||
|
||||||
Pepperl+Fuchs AG
Längfeldweg 116
2504 Biel/Bienne
Suisse
info@ch.pepperl-fuchs.com
+41 32 374 76 76
Pepperl+Fuchs est leader comme concepteur et fabricant de capteurs et composants électroniques pour le marché mondial de l'automatisation. L'innovation constante, la qualité incontestable et la croissance soutenue, garantissent notre succès, depuis plus de 70 ans. Pepperl+Fuchs emploie 6300 personnes dans le monde et compte des usines en Allemagne, aux USA, à Singapour, en Hongrie, en Indonésie et au Vietnam ; la plupart d'entre elles sont certifiées ISO 9001.