RFID read/write device hazardous area IQT1-FP-IO-C1D1
- Explosion-proof housing
- Operating frequency 13.56 MHz
- Conforms to ISO 15693
- Suitable for FRAM transponder
- Connection via screw terminals
- Approved for Class I, Groups C, D
Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.
Téléchargez ici la fiche technique complète en PDF ::
Caractéristiques techniques IQT1-FP-IO-C1D1
| Description produit |
|---|
| RFID read/write device hazardous area |
| General specifications | ||
|---|---|---|
| Operating frequency | 13.56 MHz | |
| Transfer rate | 26 kBit/s | |
| Sensing range | ||
| Read distance | 0 ... 44 mm | |
| Write distance | 0 ... 44 mm | |
| Width | max. 48 mm | |
| UL File Number | E254700 | |
| MTBF | 140 a (Operation at +40 °C) | |
| Indicators/operating means | ||
| LED red/green | Green: power on Flashing green: IO-Link communication Flashing red/green: IO-Link communication interrupted |
|
| LED blue/yellow | Blue: Write/read attempt performed Yellow: Read/write tag detected |
|
| Electrical specifications | ||
| Rated operating voltage | 20 ... 30 V DC , ripple 10 %SS | |
| Power consumption | ≤ 2 W | |
| Interface | ||
| Interface type | IO-Link | |
| IO-Link revision | 1.1 | |
| Process data | Input 32 Byte Output 32 Byte |
|
| Vendor ID | 1 (0x0001) | |
| Data transfer rate | COM3 (230.4 kbits/s) | |
| Min. cycle time | 4 ms | |
| SIO mode support | no | |
| Compatible master port type | Class A Class B |
|
| Standard conformity | ||
| RFID | ISO/IEC 15693-2 ISO/IEC 15693-3 ISO/IEC 18000-3 |
|
| Approvals and certificates | ||
| UL approval | Class I, Division 1, Groups C, D | |
| FCC approval | This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. |
|
| IC approval | This device complies with Industry Canada licence-exempt RSS standard(s) and with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. |
|
| Radio approval | USA: FCC IREIQT1FPIO Canada: 7037A-IQT1FPIO |
|
| Ambient conditions | ||
| Ambient temperature | -25 ... 70 °C (-13 ... 158 °F) | |
| Storage temperature | -40 ... 85 °C (-40 ... 185 °F) | |
| Mechanical specifications | ||
| Degree of protection | NEMA Type 4, 7, 9 | |
| Connection | Terminals | |
| Material | ||
| Housing | diecast aluminum | |
| Base | diecast aluminum | |
| Installation | ||
| Distance between two heads | ≥ 150 mm |
|
| Mass | approx. 4080 g | |
| Dimensions | ||
| Height | 140 mm | |
| Width | 157 mm | |
| Length | 157 mm | |
Classifications
| System | Classcode |
|---|---|
| ECLASS 13.0 | 27280401 |
| ECLASS 12.0 | 27280401 |
| ECLASS 11.0 | 27280401 |
| ECLASS 10.0.1 | 27280401 |
| ECLASS 9.0 | 27280401 |
| ECLASS 8.0 | 27280401 |
| ECLASS 5.1 | 27280401 |
| ETIM 9.0 | EC002998 |
| ETIM 8.0 | EC002998 |
| ETIM 7.0 | EC002998 |
| ETIM 6.0 | EC002998 |
| ETIM 5.0 | EC002998 |
| UNSPSC 12.1 | 43211710 |
Details: IQT1-FP-IO-C1D1
Product Documentation: IQT1-FP-IO-C1D1
| Product information | Langue | Type de fichier | Taille |
|---|---|---|---|
| Installation and user instructions for offline parameterization of IO-Link sensors | ENG | 1788 KB | |
| Manuals | |||
| Manual | ENG | 2227 KB | |
Design / Simulation: IQT1-FP-IO-C1D1
| CAD | Langue | Type de fichier | Taille |
|---|---|---|---|
| CAD 2-D / CAD 2-D | ALL | ZIP | 1024 KB |
Approvals: IQT1-FP-IO-C1D1
| Certificates | Identification | Langue | Type de fichier | Taille |
|---|---|---|---|---|
| USA FCC Approval | IREIQT1FPIO | ALL | 127 KB |
Software: IQT1-FP-IO-C1D1
Get to know the new IUT-F190-B40, which is designed for medium detection ranges, and can be quickly and easily integrated into OT and IT systems …
Visitez notre « Hub RFID » : ce site Internet spécial constitue une base de connaissances de la RFID. Obtenez des réponses aux questions fréquemment posées et découvrez les applications RFID types…
Pepperl+Fuchs AG
Längfeldweg 116
2504 Biel/Bienne
Suisse
info@ch.pepperl-fuchs.com
+41 32 374 76 76
Pepperl+Fuchs est leader comme concepteur et fabricant de capteurs et composants électroniques pour le marché mondial de l'automatisation. L'innovation constante, la qualité incontestable et la croissance soutenue, garantissent notre succès, depuis plus de 70 ans. Pepperl+Fuchs emploie 6300 personnes dans le monde et compte des usines en Allemagne, aux USA, à Singapour, en Hongrie, en Indonésie et au Vietnam ; la plupart d'entre elles sont certifiées ISO 9001.