请注意：所有以Pepperl + Fuchs GmbH或Pepperl + Fuchs AG名义发行的产品相关文件，例如证书，合格声明等，同样适用于Pepperl + Fuchs SE。
產品規格摘要：的技術資料
OQD8000-R300-2EP-V1-L
| 產品描述 |
| Diffuse sensor with measurement core technology |
| General specifications |
| Detection range | 0.03 ... 8 m |
| Adjustment range | 0.05 ... 8 m |
| Reference target | Kodak white (90%) |
| Light type | modulated visible red light |
| Laser nominal ratings | |
| Note | LASER LIGHT , DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS |
| Laser class | 1M |
| Wave length | 660 nm |
| Beam divergence | < 25 mrad |
| Pulse length | 4 ns |
| Repetition rate | 250 kHz |
| max. pulse energy | < 2.4 nJ |
| Black-white difference (6 %/90 %) | < 0.5 % |
| Angle deviation | max. ± 2° |
| Measuring method | Pulse Ranging Technology (PRT) |
| Diameter of the light spot | vertical 60 mm , horizontal 30 mm at a distance of 2 m |
| Ambient light limit | 50000 Lux |
| Functional safety related parameters |
| MTTFd | 100 a |
| Mission Time (TM) | 10 a |
| Diagnostic Coverage (DC) | 0 % |
| Indicators/operating means |
| Operation indicator | LED green |
| Function indicator | 2 LEDs yellow for switching state |
| Teach-in indicator | Teach-In: LED green/yellow equiphase flashing; 2.5 Hz
Teach Error:LED green/yellow non equiphase flashing; 8.0 Hz |
| Control elements | 5-step rotary switch for operating modes selection (threshold setting and operating modes) |
| Control elements | Switch for setting the threshold values |
| Electrical specifications |
| Operating voltage | 10 ... 30 V DC |
| Ripple | 10 % within the supply tolerance |
| No-load supply current | ≤ 80 mA / 24 V DC |
| Time delay before availability | < 0.7 s , for temperatures <-30°C compliance of the specification 5 mins after power on |
| Output |
| Signal output | 2 push-pull (4 in 1) outputs, short-circuit protected, reverse polarity protected |
| Switching voltage | max. 30 V DC |
| Switching current | max. 100 mA |
| Switching frequency | 50 Hz |
| Response time | 5 ms |
| Conformity |
| Product standard | EN 60947-5-2 |
| Laser safety | EN 60825-1:2014 |
| Approvals and certificates |
| UL approval | E87056 , cULus Listed , class 2 power supply , type rating 1 |
| FDA approval | IEC 60825-1:2014 Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007 |
| Ambient conditions |
| Ambient temperature | -40 ... 55 °C (-40 ... 131 °F) |
| Storage temperature | -40 ... 70 °C (-40 ... 158 °F) |
| Mechanical specifications |
| Degree of protection | IP67 |
| Connection | 4-pin, M12 x 1 connector |
| Material | |
| Housing | Plastic ABS |
| Optical face | PMMA |
| Mass | 90 g |
| Dimensions | |
| Height | 88 mm |
| Width | 25.8 mm |
| Depth | 54.3 mm |
Classifications
| System | Classcode |
| ECLASS 13.0 | 27270903 |
| ECLASS 12.0 | 27270903 |
| ECLASS 11.0 | 27270903 |
| ECLASS 10.0.1 | 27270903 |
| ECLASS 9.0 | 27270903 |
| ECLASS 8.0 | 27270903 |
| ECLASS 5.1 | 27270903 |
| ETIM 9.0 | EC001821 |
| ETIM 8.0 | EC001821 |
| ETIM 7.0 | EC001821 |
| ETIM 6.0 | EC001821 |
| ETIM 5.0 | EC001821 |
| UNSPSC 12.1 | 39121528 |
Details:
OQD8000-R300-2EP-V1-L
Product Documentation:
OQD8000-R300-2EP-V1-L
Design / Simulation:
OQD8000-R300-2EP-V1-L
Approvals:
OQD8000-R300-2EP-V1-L
相關產品:
OQD8000-R300-2EP-V1-L
| Accessories |
|
|
|
| Mounting aid for round steel ø 12 mm or sheet 1.5 mm ... 3 mmfa |
|
|
|
|
| Mounting bracket: mounting aid for sensors in the RL* seriesfa |
|
|
|
|
| Mounting aid for RL* seriesfa |
|
|
|
|
| Mounting bracket for rear wall mountingfa |
|
|
|
|
| dove tail mounting clampfa |
|
|
|
|
| dove tail mounting clampfa |
|
|
|
|
| Metal enclosure for inserting protective panes or aperturesfa |
|
|
|
|
| Mounting and fine adjustment device for sensors from the 28 seriesfa |
|
|
|
|
| Mounting aid for round steel ø 12 mm or sheet 1.5 mm ... 3 mmfa |
|
+886 2 27227708