HART Output Isolator FB4205B3

4-channel
Outputs Ex ia
Installation in suitable enclosures in Zone 1
Module can be exchanged under voltage (hot swap)
Analog output module for 0/4 mA ... 20 mA
HART communication via field bus or service bus
Simulation mode for service operations (forcing)
Line fault detection (LFD): one LED per channel
Permanently self-monitoring

Technical Data
Details
Informative Literature
Product Documentation
Design / Simulation
Approvals

Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.

Lataa koko tietolomake PDF-tiedostona:

Ote tietolomakkeesta: Tekniset tiedot FB4205B3

Slots
Occupied slots		2
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies FB92**
Power dissipation		1.5 W
Power consumption		3 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog input
HART communication		yes
HART secondary variable		no
Analog output
Number of channels		4
Suitable field devices
	Field device	Proportional Valve
	Field device [2]	I/P converters
	Field device [3]	on-site display
Connection		terminals 1+, 2-; 3+, 4-; 5+, 6-; 7+, 8-
Current		0 ... 20 mA short-circuit protected
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	No
	Open-circuit	deviation of preset output value > 0.5 mA
Load		max. 750 Ω at 20 mA
HART communication		yes
HART secondary variable		yes
Watchdog		within 0.5 s the device goes in safe state, e.g. after loss of communication
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
	Influence of ambient temperature	0.1 %/10 K of the signal range
Resolution		12 Bit (0 ... 26 mA)
Refresh time		approx. 100 ms (4 channels)
Indicators/settings
LED indication		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1-4) red: line fault (lead breakage or short circuit)
Coding		optional mechanical coding via front socket
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2013
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Environmental test		EN 60068-2-14:2009
Shock resistance		EN 60068-2-27:2009
Vibration resistance		EN 60068-2-6:2008
Damaging gas		EN 60068-2-42:2003
Relative humidity		EN 60068-2-78:2001
Ambient conditions
Ambient temperature		-40 ... 60 °C (-40 ... 140 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Relative humidity		95 % non-condensing
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz; transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g; 10 cycles frequency range 5 ... 100 Hz; transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g; 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 (module) , a separate housing is required acc. to the system description
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 750 g
Dimensions		57 x 107 x 132 mm (2.2 x 4.2 x 5.2 inch)
Data for application in connection with hazardous areas
EU-type examination certificate		Presafe 19 ATEX 14057U
	Marking	II 2(1)G Ex db eb q [ia Ga] IIC Gb II (1)D [Ex ia Da] IIIC I (M1) [Ex ia Ma] I
Supply
	Voltage	27 V
	Current	87 mA
	Power	575 mW (linear characteristic)
Input		Ex ia
Output		Ex ia
	Voltage	27 V
	Current	87 mA
	Power	575 mW (linear characteristic)
Galvanic isolation
	Output/power supply, internal bus	safe electrical isolation acc. to EN 60079-11:2007 , voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN IEC 60079-0:2018+AC:2020 EN 60079-1:2014 EN 60079-5:2015 EN 60079-7:2015+A1:2018 EN 60079-11:2012
International approvals
ATEX approval		Presafe 19 ATEX 14057U
IECEx approval		IECEx PRE 19.0012U
	Approved for	Ex db eb q [ia Ga] IIC Gb [Ex ia Da] IIIC [Ex ia Ma] I
General information
System information		The module has to be mounted in appropriate backplanes and housings (FB92**) in Zone 1, 2, 21, 22 or outside hazardous areas (gas or dust). Here, observe the corresponding EC-type examination certificate.
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.

Classifications

System	Classcode
ECLASS 13.0	27210120
ECLASS 12.0	27210120
ECLASS 11.0	27210120
ECLASS 10.0.1	27210120
ECLASS 9.0	27210120
ECLASS 8.0	27210120
ECLASS 5.1	27210120
ETIM 9.0	EC001485
ETIM 8.0	EC001485
ETIM 7.0	EC001485
ETIM 6.0	EC001485
ETIM 5.0	EC001485
UNSPSC 12.1	39121008

Details: FB4205B3

Function

The device drives positioners, proportional valves, I/P converters, or local indicators.

Open and short-circuit line faults are detected.

The outputs are galvanically isolated from the bus and the power supply.

Informative Literature: FB4205B3

Literature	Kieli	Tiedostotyyppi	Tiedoston koko
Application Report - Communication Redundancy for Uninterrupted Operation	ENG	PDF	529 KB
Application Report - LB and FB Remote I/O Systems for Digitally Connecting Analog Field Devices	ENG	PDF	208 KB
Application Report - Space Saving Extension for Existing Plants	ENG	PDF	300 KB
Application Report - Using Remote I/O Systems for the Efficient Digitalization of Plants	ENG	PDF	371 KB

Product Documentation: FB4205B3

Safety and Security Documentation	Kieli	Tiedostotyyppi	Tiedoston koko
Käyttöohje	FIN	PDF	171 KB
Manuals
Hardware Manual FB-Remote-I/O-System	ENG	PDF	9157 KB

Design / Simulation: FB4205B3

CAD	Kieli	Tiedostotyyppi	Tiedoston koko
CAD 3-D / CAD 3-D	ALL	STP	7300 KB
CAD Portal / CAD Portal	ALL	LINK	---
CAE
CAE EPLAN Data Portal / CAE EPLAN Data Portal	ALL	LINK	---
EPLAN macro EDZ / EPLAN Makro EDZ	ALL	EDZ	1299 KB

Approvals: FB4205B3

Certificates	Sertifikaatin nro	Kieli	Tiedostotyyppi	Tiedoston koko
China SITIIAS CCC Ex Certificate	2021322310004116 (Mannheim)	ALL	PDF	1330 KB
Europe Presafe DNV GL II 2(1)G I (M1) ATEX II (1) D	Presafe 19 ATEX 14057U	ALL	PDF	245 KB
Presafe DNV GL IECEx Certificate of Conformity	IECEx PRE 19.0012U	ALL	LINK	---
United Kingdom CML UK-Type Examination Certificate UKEX Category (1) D UKEX Category (1) G UKEX Category (M1)	CML 23UKEX2151U	ALL	PDF	166 KB
Declaration of Conformity
EU-vaatimustenmukaisuusvakuutus	TDOC-4262DFIN	FIN	PDF	1140 KB
UK-Declaration of conformity	TDOC-6776AENG	ENG	PDF	1110 KB

General Notes Relating to Pepperl+Fuchs Product Information

Pikalinkit

Pepperl+Fuchs Oy
Areenakatu 7
FI-37570 Lempäälä
Finland
info@fi.pepperl-fuchs.com
phone +358 20 7861 290
info@fi.pepperl-fuchs.com
phone +358 20 7861 291

Pepperl+Fuchs on dynaaminen ja tulevaisuuteen suuntaava yritys joka myy konepajateollisuuden, robotiikan ja teollisuusautomaation komponentteja. Tuotannon sujuvuus, tuotteiden korkea laatu ja niiden maailmanlaajuinen saatavuus ovat tuoneet yritykselle menestystä jo yli 70 vuoden ajan. Pepperl+Fuchs työllistää maailman laajuisesti yhteensä noin 6300 henkilöä. Globaalilla yrityksellä on tuotantolaitoksia Saksassa, Singaporessa, Yhdysvalloissa, Unkarissa, Indonesiassa ja Vietnamissa, joista suurin osa ovat ISO 9001-sertifioitu.