AS-Interface printed circuit board module VBA-4E4A-CB10-ZJ/E1J-FL

Integrated communication monitoring function
Outputs short-circuit and overload proof
Supply of the inputs and the outputs from AS-Interface
Function display for bus, inputs and outputs
Connection via lead

Technical Data
Details
Product Documentation
Design / Simulation
Approvals

Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.

Tam veri sayfasını PDF olarak indirin:

Veri sayfası alıntısı: Teknik veriler VBA-4E4A-CB10-ZJ/E1J-FL

Ürün Açıklaması
Printed circuit board module 4 inputs/4 outputs

General specifications
Node type		A/B node
AS-Interface specification		V3.0
Required gateway specification		≥ V3.0
UL File Number		E223772
MTBF		267 a
Indicators/operating means
LED FAULT		error display; LED red red: communication error or address is 0 red flashing: overload of outputs
LED PWR		AS-Interface voltage; green LED green: voltage OK flashing green: address 0
LED IN		switching state (input); 4 LED yellow
LED OUT		Switching state (output); 4 LED yellow
Electrical specifications
Rated operating voltage		26.5 ... 31.6 V from AS-Interface (PELV)
Rated operating current		≤ 40 mA (without inputs/outputs)/max. 160 mA
Protection class		III
Surge protection		U_e: overvoltage category II, safe isolated power supplies (PELV)
Input
Number/Type		4 inputs for mechanical contacts
Supply		from AS-Interface
Voltage		12 ... 31 V
Input current		≤ 4 mA (limited internally)
Switching point
	0 (unattenuated)	≤ 0.15 mA
	1 (attenuated)	≥ 1.3 mA
Signal delay		< 1 ms (input/AS-Interface)
Output
Number/Type		4 electronic outputs, NPN, overload proof and short-circuit proof
Supply		from AS-Interface
Voltage		12 ... 31 V
Current		≤ 100 mA per output, ≤ 100 mA total
Usage category		DC-1 "general use" (ohmic and weak inductive loads in accordance with IEC 60947)
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 62026-2:2013
Standard conformity
Degree of protection		EN 60529:2000
Fieldbus standard		EN 62026-2:2013
Emitted interference		EN 61000-6-4:2007
AS-Interface		EN 62026-2:2013
Noise immunity		EN 61000-6-2:2005, EN 61326-1:2006, EN 62026-2:2013
Programming instructions
Profile		S-7.A.7
IO code		7
ID code		A
ID1 code		7
ID2 code		7
Data bits (function via AS-Interface)		InputOutput
	D0	IN1 OUT1
	D1	IN2 OUT2
	D2	IN3 OUT3
	D3	IN4 OUT4
Parameter bits (programmable via AS-i)		function
	P0	not used
	P1	Input filter P1 = 0 input filter on, pulse suppression ≤ 2 ms P1 = 1 input filter off (default settings)
	P2	Synchronous mode P2 = 0 synchronous mode on P2 = 1 synchronous mode off (default settings)
	P3	not used
Approvals and certificates
UL approval		Protection class IP20 is not included in the UL approval. The protection class is tested by Pepperl+Fuchs.
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Relative humidity		85 % , noncondensing
Climatic conditions		For indoor use only
Altitude		≤ 5000 m above MSL
Shock and impact resistance		30 g, 11 ms in 6 spatial directions, 3 shocks 10 g, 16 ms in 6 spatial directions, 1000 shocks
Vibration resistance		0.35 mm 10 ... 57 Hz , 5 g, 57 Hz ... 150 Hz, 10 cycles
Pollution degree		2
Mechanical specifications
Degree of protection		IP20 according to EN 60529
Connection		200 mm, PVC cable 0.5 mm²
Material
	Housing	Polyamide hot-melt adhesive
Mass		33 g
Dimensions
	Height	10 mm
	Width	36 mm
	Length	39.5 mm
Note		This device is maintenance-free. If the device is used in a manner not specified by the manufaturer, the protection provided by the device may be impaired.

Classifications

System	Classcode
ECLASS 13.0	27242604
ECLASS 12.0	27242604
ECLASS 11.0	27242604
ECLASS 10.0.1	27242604
ECLASS 9.0	27242604
ECLASS 8.0	27242604
ECLASS 5.1	27242604
ETIM 9.0	EC001599
ETIM 8.0	EC001599
ETIM 7.0	EC001599
ETIM 6.0	EC001599
ETIM 5.0	EC001599
UNSPSC 12.1	39121535

Details: VBA-4E4A-CB10-ZJ/E1J-FL

Function

The AS-Interface connecting module is ideal for integrating custom electronics, such as illuminated pushbuttons or LED lights. The PCB is supplied with power entirely via AS-Interface. The inputs and outputs are resistant to short circuits and overloading. The display and control elements and AS-Interface are connected via cable strands.

A signal indicating an overload of the outputs is transmitted to the AS-Interface master via the "peripheral fault" function. The communication via AS-Interface remains unaffected.

Note:

A communication monitoring function is integrated into the system. This function disconnects the outputs from the power supply when no communication is taking place on the AS-Interface line.

Product Documentation: VBA-4E4A-CB10-ZJ/E1J-FL

Brief Instructions	Dil	Dosya Tipi	Dosya Boyutu
Instruction leaflet / Beipackzettel	ALL	PDF	210 KB

Design / Simulation: VBA-4E4A-CB10-ZJ/E1J-FL

CAE	Dil	Dosya Tipi	Dosya Boyutu
CAE EPLAN Data Portal / CAE EPLAN Data Portal	ALL	LINK	---
CAE EPLAN macro EDZ / CAE EPLAN Makro EDZ	ALL	EDZ	281 KB

Approvals: VBA-4E4A-CB10-ZJ/E1J-FL

Certificates	Sertifika No.	Dil	Dosya Tipi	Dosya Boyutu
US CA UL	E223772	ALL	LINK	---
Worldwide AS-International Association AS-Interface	128701	ALL	PDF	132 KB
Declaration of Conformity
EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F)	DOC-3534A	ALL	PDF	108 KB

General Notes Relating to Pepperl+Fuchs Product Information

Linkler

Pepperl+Fuchs Elektronik San. ve Tic. Ltd. Şti.
Atatürk Mah. Şeref Sok. No: 9
34758 Ataşehir
Türkiye
phone +90 216 577 2250

Pepperl+Fuchs, endüstriyel sensörlerin üretimi ve geliştirilmesinde küresel otomasyon pazarının lider firmalarından biridir.Yenilikçi yaklaşım, kaliteden ödün vermeme ve istikrarlı büyüme 70 yıldan beri devam eden başarımızı garanti etmektedir. Pepperl+Fuchs’un dünya çapında 6.300 çalışanı mevcuttur ve Almanya, ABD, Singapur, Macaristan, Endonezya ve Vietnam’da çoğu ISO 9001 sertifikalı, üretim tesisleri bulunmaktadır.