Fabrika Otomasyonu
Proses Otomasyonu
Solenoid Driver HiC2883
- 1-channel isolated barrier
- 24 V DC supply (bus or loop powered)
- Output 45 mA at 12 V DC
- Line fault transparency (LFT)
- Test pulse immunity
- Up to SIL 3 acc. to IEC/EN 61508
Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.
Tam veri sayfasını PDF olarak indirin:
Veri sayfası alıntısı: Teknik veriler HiC2883
| General specifications | ||
|---|---|---|
| Signal type | Digital Output | |
| Functional safety related parameters | ||
| Safety Integrity Level (SIL) | SIL 3 | |
| Systematic capability (SC) | SC 3 | |
| Supply | ||
| Connection | SL1: 1a, 1b(-); 2a, 2b(+) | |
| Rated voltage | 19 ... 30 V bus powered via Termination Board 19 ... 30 V loop powered via input , reverse polarity protected |
|
| Input current | 75 mA at 24 V, 270 Ω load | |
| Power dissipation | 1.3 W at 24 V, 270 Ω load | |
| Input | ||
| Connection side | control side | |
| Connection | SL1: 7a(-), 9a(-); 8a(+), 10a(+) | |
| Test pulse length | max. 2 ms from DO card | |
| Signal level | loop powered 1-signal: 19 ... 30 V DC 0-signal: 0 ... 5 V DC bus powered 1-signal: 15 ... 30 V DC (current limited to 5 mA) 0-signal: 0 ... 5 V DC |
|
| Rated current | 0-signal: typ. 1.6 mA at 1.5 V DC; typ. 8 mA at 3 V DC (maximum leakage current DO card) 1-signal: ≥ 36 mA (minimum load current DO card) |
|
| Inrush current | < 200 mA , 10 ms loop powered | |
| Output | ||
| Connection side | field side | |
| Connection | SL2: 5a(+), 5b(-) | |
| Internal resistor | approx. 240 Ω | |
| Current | typ. 45 mA | |
| Voltage | ≥ 12 V | |
| Current limit | 50 mA | |
| Open loop voltage | typ. 24.6 V | |
| Load | nominal 0.05 ... 18 kΩ , valid range for line fault detection (LFD) | |
| Switching frequency | max. 10 Hz | |
| Energized/De-energized delay | 20 ms / 5 ms | |
| Line fault detection | ||
| Test current | max. 350 µA , calculated by ILFD = 4.7 V / (15 kΩ + RLoad) | |
| Fault indication output | ||
| Connection | SL1: 6b | |
| Output type | open collector transistor (internal fault bus) | |
| Galvanic isolation | ||
| Output/other circuits | basic insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff | |
| Indicators/settings | ||
| Display elements | LEDs | |
| Control elements | DIP switch | |
| Configuration | via DIP switches | |
| Labeling | space for labeling at the front | |
| Directive conformity | ||
| Electromagnetic compatibility | ||
| Directive 2014/30/EU | EN 61326-1:2013 (industrial locations) | |
| Conformity | ||
| Electromagnetic compatibility | NE 21:2017 , IEC/EN 61326-3-2:2018 For further information see system description. |
|
| Degree of protection | IEC 60529:2013 | |
| Protection against electrical shock | UL 61010-1:2012 | |
| Ambient conditions | ||
| Ambient temperature | -40 ... 70 °C (-40 ... 158 °F) | |
| Mechanical specifications | ||
| Degree of protection | IP20 | |
| Mass | approx. 150 g | |
| Dimensions | 12.5 x 106 x 128 mm (0.5 x 4.2 x 5.1 inch) (W x H x D) | |
| Mounting | on termination board | |
| Coding | pin 1 and 4 trimmed For further information see system description. |
|
| Data for application in connection with hazardous areas | ||
| EU-type examination certificate | FIDI 21 ATEX 0069X | |
| Marking |  II 3(1)G Ex nC ec [ia Ga] IIC T4 Gc II (1)D [Ex ia Da] IIIC I (M1) [Ex ia Ma] I |
|
| Output | Ex ia | |
| Voltage | 26 V | |
| Current | 110 mA | |
| Power | 715 mW | |
| Supply | ||
| Maximum safe voltage | 60 V (Attention! The rated voltage can be lower.) | |
| Input | ||
| Maximum safe voltage | 60 V (Attention! The rated voltage can be lower.) | |
| Galvanic isolation | ||
| Input/Output | safe electrical isolation acc. to IEC/EN 60079-11, rated insulation voltage 300 Vrms | |
| Directive conformity | ||
| Directive 2014/34/EU | EN IEC 60079-0:2018+AC:2020 , EN 60079-7:2015+A1:2018 , EN 60079-11:2012 , EN IEC 60079-15:2019 | |
| International approvals | ||
| FM approval | FM 17 US 0111 X , FM 17 CA 0057 X | |
| Control drawing | 116-0442 | |
| UL approval | E106378 | |
| Control drawing | 116-0447A (cULus) | |
| IECEx approval | ||
| IECEx certificate | IECEx EXA 17.0009X | |
| IECEx marking | Ex nC ec [ia Ga] IIC T4 Gc [Ex ia Da] IIIC [Ex ia Ma] I |
|
| General information | ||
| Supplementary information | Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com. | |
Classifications
| System | Classcode |
|---|---|
| ECLASS 13.0 | 27210101 |
| ECLASS 12.0 | 27210190 |
| ECLASS 11.0 | 27210190 |
| ECLASS 10.0.1 | 27210190 |
| ECLASS 9.0 | 27210190 |
| ECLASS 8.0 | 27210190 |
| ECLASS 5.1 | 27210121 |
| ETIM 9.0 | EC001485 |
| ETIM 8.0 | EC001485 |
| ETIM 7.0 | EC001485 |
| ETIM 6.0 | EC001485 |
| ETIM 5.0 | EC001485 |
| UNSPSC 12.1 | 39121008 |
Details: HiC2883
Function
This isolated barrier is used for intrinsic safety applications.
It supplies power to solenoids, LEDs and audible alarms located in a hazardous area.
The device is controlled with a loop powered signal or a bus powered logic signal.
The device is immune to the test pulses of various control systems.
The device simulates a minimum load at the input. The minimum load can be activated and de-activated.
The line fault transparency function can display a line fault in the field by a change in impedance at the switching input of the solenoid driver.
The line fault transparency function is only available, if the device is supplied via the termination board.
Product Documentation: HiC2883
| Safety and Security Documentation | Dil | Dosya Tipi | Dosya Boyutu |
|---|---|---|---|
| Instruction manual | ENG | 151 KB | |
| Functional Safety Manual | ENG | 1959 KB | |
| Manuals | |||
| System Manual | ENG | 5438 KB | |
Design / Simulation: HiC2883
| CAD | Dil | Dosya Tipi | Dosya Boyutu |
|---|---|---|---|
| CAD 3-D / CAD 3-D | ALL | STP | 2770 KB |
| CAD Portal / CAD Portal | ALL | LINK | --- |
Approvals: HiC2883
İlişkili Ürünler: HiC2883
| Matching System Components | ||||||
|---|---|---|---|---|---|---|
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
SIL/PL değerlendirmesi içeren yüzlerce ürün, ücretsiz araçlar ve broşürler tek bir yerde: Güvenlik işlevleri uygulamanız gerektiğinde başlangıç noktanız, "Fonksiyonel Güvenlik Merkezi"dir.
The largest portfolio of its kind: K-System components and systems are established in process industries around the world. Learn more!
Pepperl+Fuchs Elektronik San. ve Tic. Ltd. Şti.
Atatürk Mah. Şeref Sok. No: 9
34758 Ataşehir
Türkiye
+90 216 577 2250
© 2024 Tüm Hakları Saklıdır.
Pepperl+Fuchs, endüstriyel sensörlerin üretimi ve geliştirilmesinde küresel otomasyon pazarının lider firmalarından biridir.Yenilikçi yaklaşım, kaliteden ödün vermeme ve istikrarlı büyüme 70 yıldan beri devam eden başarımızı garanti etmektedir. Pepperl+Fuchs’un dünya çapında 6.300 çalışanı mevcuttur ve Almanya, ABD, Singapur, Macaristan, Endonezya ve Vietnam’da çoğu ISO 9001 sertifikalı, üretim tesisleri bulunmaktadır.