UC2000-30GM-IUEP-IO-V15 Ultrasonic sensor

Key Benefits at a Glance

IO-Link interface for service and process data
Programmable via DTM with PACTWARE
Switch output and analog output
Selectable sound lobe width
Synchronization options
Temperature compensation

Please contact us for exact delivery estimation.626.00 AUD

Product photo: Ultrasonic sensor UC2000-30GM-IUEP-IO-V15

Dimensions: Ultrasonic sensor UC2000-30GM-IUEP-IO-V15

Connection Assignment: Ultrasonic sensor UC2000-30GM-IUEP-IO-V15

Note

All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.

Datasheet Classification Informative Literature Product Documentation Design / Simulation Approvals Software Related Products

Technical data of UC2000-30GM-IUEP-IO-V15

Single head system

Sensing range		90 ... 2000 mm
Adjustment range		120 ... 2000 mm
Dead band		0 ... 90 mm
Standard target plate		100 mm x 100 mm
Transducer frequency		approx. 200 kHz
Response delay		minimum : 65 ms factory setting: 125 ms

Non-volatile memory		EEPROM
Write cycles		100000

LED green		solid: Power on flashing: Standby mode or IO link communication
LED yellow 1		solid: Object in evaluation range flashing: Learning function, object detected
LED yellow 2		solid: Object in evaluation range flashing: Learning function, object detected
LED red		solid red: Error red, flashing: program function, object not detected

Operating voltage	U_B	10 ... 30 V DC , ripple 10 %_SS 15 ... 30 V voltage output
No-load supply current	I₀	≤ 60 mA
Power consumption	P₀	≤ 1 W
Time delay before availability	t_v	≤ 120 ms

Interface type		IO-Link
Protocol		IO-Link V1.0
Transfer rate		Acyclical: typical 95 Bit/s
Cycle time		min. 33.6 ms
Mode		COM2 (38.4 kBit/s)
Process data width		16 bit
SIO mode support		yes

Input/output type

1 synchronization connection, bidirectional

0 Level		0 ... 1 V
1 Level		4 V ... U_B
Input impedance		> 12 kΩ
Output current		< 12 mA
Pulse length		0.5 ... 300 ms (level 1)
Pulse interval		≥ 33 ms (level 0)

Synchronization frequency

Common mode operation		≤ 30 Hz
Multiplex operation		≤ 33 Hz / n , n = number of sensors , n ≤ 10 (factory setting: n = 5 )

Output type		1 push-pull (4 in 1) output, short-circuit protected, reverse polarity protected Current output 4 mA ... 20 mA or voltage output 0 V ... 10 V configurable
Rated operating current	I_e	200 mA , short-circuit/overload protected
Voltage drop	U_d	≤ 2.5 V
Resolution		current output: evaluation range [mm]/3200 but ≥ 0.35 mm voltage output: evaluation range [mm]/4000 but ≥ 0.35 mm
Deviation of the characteristic curve		≤ 0.2 % of full-scale value
Repeat accuracy		≤ 0.1 % of full-scale value
Switching frequency	f	≤ 4 Hz
Range hysteresis	H	1 % of the adjusted operating range (default settings), programmable
Load impedance		current output: ≤ 300 Ohm voltage output: ≥ 1000 Ohm
Temperature influence		≤ 1.5 % from full-scale value (with temperature compensation) ≤ 0.2 %/K (without temperature compensation)

Standard conformity

Standards

EN IEC 60947-5-2:2020
IEC 60947-5-2:2019
EN 60947-5-7:2003
IEC 60947-5-7:2003

UL approval		cULus Listed, Class 2 Power Source
CCC approval		CCC approval / marking not required for products rated ≤36 V

Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)

Connection type

Connector plug M12 x 1 , 5-pin

Degree of protection

IP67

Material

Housing		Stainless steel 1.4305 / AISI 303 TPU Polyamides
Transducer		epoxy resin/hollow glass sphere mixture; polyurethane foam

Mass

72 g

Dimensions

Length		93 mm
Diameter		30 mm

Output 1		near switch point: 120 mm far switch point: 2000 mm Output mode: Window mode output behavior: NO contact
Output 2		near limit: 120 mm far limit: 1000 mm Output mode: rising ramp output behavior: Current output 4 mA ... 20 mA
Beam width		wide

General Notes

We value your privacy!

We and our partners are using technologies like cookies and process personal data like the IP-address or browser information in order to personalize the advertising that you see. This helps us to show you more relevant ads and improves your internet experience. We also use it in order to measure results or align our website content. Because we value your privacy, we are herewith asking for your permission to use these technologies. You can always change/withdraw your consent later by clicking on the settings button on the left lower corner of the page.

Categories	Description	Status
Functional	These cookies are necessary so that you can navigate through the pages and use essential functions (e.g. login).
Analytics	We use these cookies and scripts to measure the visits and clicks on our website in order to constantly improve it.
Marketing	These cookies and similar technologies are used to provide you with personalized and therefore relevant advertising content.