Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.
Last ned komplett datablad som PDF:
General specifications | ||
---|---|---|
Sensing range | 20 ... 60 mm , optimal distance: 45 mm | |
Transducer frequency | approx. 255 kHz | |
Memory | ||
Non-volatile memory | EEPROM | |
Write cycles | 300000 | |
Indicators/operating means | ||
LED green | indication: single sheet detected flashing (1 Hz) - standby mode flashing with short break (1 Hz) - IO-Link mode |
|
LED yellow | indication: no sheet detected (Air) | |
LED red | indication: double sheet detected flashing: device error |
|
Electrical specifications | ||
Operating voltage | 18 ... 30 V DC , ripple 10 %SS | |
No-load supply current | ≤ 40 mA | |
Power consumption | ≤ 550 mW | |
Time delay before availability | ≤ 300 ms | |
Interface | ||
Interface type | IO-Link | |
IO-Link revision | 1.1 | |
Device profile | Identification and Diagnosis - I&D | |
Process data | Input: 16 Bit - measurement value 8 Bit - selected threshold set 2 Bit - switching signals 3 Bit Output: 8 Bit - threshold set 2 Bit - disable transducer 1 Bit |
|
Vendor ID | 1 (0x0001) | |
Device ID | 3148290 (0x300A02) | |
Transfer rate | COM2 (38.4 kBit/s) | |
Min. cycle time | 2.8 ms | |
SIO mode support | yes | |
Compatible master port type | Class A (use adapter cable listed in accesories) Class B (use 3-pole adapter or 3-wire cable) |
|
Input/Output 1 | ||
Designation | SYNC | |
Input/output type | 1 synchronization connection, bidirectional | |
0 Level | 0 ... 1 V | |
1 Level | 2.5 V ... UB | |
Input impedance | > 22 kΩ | |
Output rated operating current | current source < 2.5 mA | |
Pulse length | 0.4 ... 3 ms with external control, low active | |
Synchronization frequency | ||
Common mode operation | ≤ 230 Hz | |
Multiplex operation | ≤ 230 Hz /n, n = number of sensors , n ≤ 10 | |
Input/Output 2 | ||
Designation | IN2/FEEDBACK | |
Input/output type | input or output programmable via IO-Link : input for selection of a threshold set (factory default) output as feedback output |
|
Input type | digital input | |
Signal | 0-level: 0 ... + 1V 1-level: +UB - 1 V ... +UB |
|
Input impedance | ≥ 60 kΩ | |
Pulse length | ≥ 100 ms | |
Output type | PNP | |
Rated operating current | 8 mA | |
Voltage drop | < 3 V | |
Fusing | reverse polarity protected , overload and short-circuit protected | |
Input | ||
Designation | IN1/TEACH | |
Input type | 0-level: 0 ... + 1V 1-level: +UB - 1 V ... +UB |
|
Pulse length | ≥ 100 ms | |
Impedance | ≥ 60 kΩ | |
Output | ||
Designation | OUT 1 ... 3 | |
Number | 3 | |
Output function | OUT 1: single sheet detected OUT 2: double sheet detected OUT 3: no sheet detected (air) |
|
Output type | Push-pull (4 in 1) output , NC contact ( programmable ) | |
Rated operating current | 100 mA per output | |
Voltage drop | ≤ 3 V | |
Switch-on delay | 15 ms (programmable) | |
Switch-off delay | 15 ms (programmable) | |
Pulse extension | can be activated (100 ms or IO-Link cycle time) | |
Fusing | reverse polarity protected , overload and short-circuit resistant | |
Compliance with standards and directives | ||
Standard conformity | ||
Standards | EN IEC 60947-5-2:2020 IEC 60947-5-2:2019 IEC 61131-9 / IO-Link V1.1.3 |
|
Approvals and certificates | ||
UL approval | cULus Listed, General Purpose, Class 2 Power Source | |
CCC approval | CCC approval / marking not required for products rated ≤36 V | |
Ambient conditions | ||
Ambient temperature | 0 ... 60 °C (32 ... 140 °F) | |
Storage temperature | -25 ... 70 °C (-13 ... 158 °F) | |
Mechanical specifications | ||
Connection type | fixed cable with plug | |
Housing length | ||
Ultrasonic transmitter | 21 mm | |
Ultrasonic receiver | 52 mm | |
Housing diameter | ||
Ultrasonic transmitter | 18 mm | |
Ultrasonic receiver | 18 mm | |
Degree of protection | IP65 | |
Material | ||
Housing | Stainless steel 1.4305/AISI 303, polyamide plastic parts | |
Transducer | epoxy resin/hollow glass sphere mixture; polyurethane foam | |
Connector | ||
Threading | M12 x 1 | |
Number of pins | 8 | |
Cable | ||
Cable diameter | 4.3 mm | |
Bending radius | 5 x diameter , fixed installation | |
Material | PUR | |
Color | black | |
Length | approx. 200 mm | |
Mass | 75 g | |
Tightening torque, fastening screws | max. 20 Nm |
System | Classcode |
---|---|
ECLASS 13.0 | 27272801 |
ECLASS 12.0 | 27272801 |
ECLASS 11.0 | 27272801 |
ECLASS 10.0.1 | 27272801 |
ECLASS 9.0 | 27272801 |
ECLASS 8.0 | 27272801 |
ECLASS 5.1 | 27272801 |
ETIM 9.0 | EC001847 |
ETIM 8.0 | EC001847 |
ETIM 7.0 | EC001847 |
ETIM 6.0 | EC001847 |
ETIM 5.0 | EC001847 |
UNSPSC 12.1 | 41111960 |
The ultrasonic double-sheet detector is used wherever automatic differentiation between single and double sheets is necessary to protect machines or prevent rejects. The double sheet detection is based on the ultrasonic thru-beam principle.
The following situations can be detected:
No sheet, i. e. air
Single sheet
Double sheet or multiple sheets (a statement on the number of sheets is not possible here)
The signals are evaluated by a microprocessor system. As a result of the evaluation, corresponding switching outputs are set and the result of the evaluation is communicated via the IO-Link interface.
Literature | Språk | Filtype | Filstørrelse |
---|---|---|---|
Application Report - Reliable Detecting Foil Tears in Battery Cell Manufacturing | ENG | 163 KB |
Brief Instructions | Språk | Filtype | Filstørrelse |
---|---|---|---|
Commissioning instruction for series UDC-18GS-* / Inbetriebnahmeanleitung für Serie UDC-18GS-* | ALL | 379 KB | |
Safety and Security Documentation | |||
Bruksanvisningen | NOR | 145 KB | |
Manuals | |||
Manual UDC-/UDCM-*GS-*-IO*-Series Parameterization of Ultrasonic Double Sheet Sensors with IO-Link Interface | ENG | 4602 KB | |
Parameter Information | |||
IO-Link Parameter-Datasheet UDC-18GS-3EP1-IO-0,2M-V19 | ENG | 584 KB |
CAD | Språk | Filtype | Filstørrelse |
---|---|---|---|
CAD 3-D / CAD 3-D | ALL | STP | 6865 KB |
CAD Portal / CAD Portal | ALL | LINK | --- |
CAE | |||
CAE EPLAN Data Portal / CAE EPLAN Data Portal | ALL | LINK | --- |
CAE EPLAN macro EDZ / CAE EPLAN Makro EDZ | ALL | EDZ | 75 KB |
Certificates | Sertifikatnummer | Språk | Filtype | Filstørrelse |
---|---|---|---|---|
Canada USA UL Ordinary Location | UL-US-2140156-4 / UL-CA-2133660-4 | ALL | 284 KB | |
IO-Link Manufacturer Declaration | CERT-6559A | ALL | 295 KB | |
Declaration of Conformity | ||||
EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F) | DOC-5827 | ALL | 34 KB | |
UK Declaration of Conformity (P+F) / UK-Konformitäterklärung (P+F) | DOC-5828 | ALL | 32 KB |
Device Description Files/Drivers | Frigivelsesinfo | Filtype | Filstørrelse |
---|---|---|---|
IODD for UDC-18GS-3EP1 / IODD für UDC-18GS-3EP1 | V1.00.000 / 2022-03-30 | ZIP | 300 KB |
DTM (Device Type Manager) Package for UDC-18GS*/UDC-30GS* ultrasonic sensors / DTM (Device Type Manager) Package für UDC-18GS*/UDC-30GS* Ultraschallsensoren | V1.1.0.0 / 08-08-2022 | ZIP | 16847 KB |
Software Tools | |||
IO-Link Offline Parameterization Tool / IO-Link Offline-Parametriertool | V1.00.006 / 2022-07-10 | ZIP | 96138 KB |
Accessories | ||||||
---|---|---|---|---|---|---|
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|