Solenoid Driver HiC2877
- 1-channel isolated barrier
- 24 V DC supply (bus or loop powered)
- Output 40 mA at 11.2 V DC, 55 mA current limit
- Contact or logic control input
- Entity parameter Io/Isc = 93 mA
- Line fault detection (LFD)
- Test pulse immunity
- Up to SIL 3 acc. to IEC/EN 61508 (loop powered)
Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.
Last ned komplett datablad som PDF:
Datablad utdrag: Tekniske data for HiC2877
| General specifications | ||
|---|---|---|
| Signal type | Digital Output | |
| Functional safety related parameters | ||
| Safety Integrity Level (SIL) | SIL 3 | |
| Systematic capability (SC) | SC 3 | |
| Supply | ||
| Connection | SL1: 1a, 1b(-); 2a, 2b(+) | |
| Rated voltage | 20.4 ... 30 V DC loop powered 20.4 ... 30 V DC bus powered via Termination Board |
|
| Input current | 62 mA at 24 V, 300 Ω load | |
| Power dissipation | 1 W at 24 V, 300 Ω load | |
| Input | ||
| Connection side | control side | |
| Connection | SL1: 8a(+), 7a(-) loop powered SL1: 10a(+), 9a(-) bus powered |
|
| Control input | external switch (dry contact or open collector) non isolated or logic signal input fully floating | |
| Signal level | 1-signal: 15...30 V DC (current limited to 3 mA) or contact close (internal 10 kΩ pull-up) 0-signal: 0...5 V DC or contact open |
|
| Power dissipation | 1 W at 24 V, 300 Ω load for loop powered | |
| Inrush current | 0.2 A , 15 ms loop powered | |
| Output | ||
| Connection side | field side | |
| Connection | SL2: 5a(+), 5b(-) | |
| Internal resistor | approx. 280 Ω | |
| Current | ≤ 40 mA | |
| Voltage | ≥ 11.2 V | |
| Current limit | 55 mA | |
| Open loop voltage | approx. 22.5 V | |
| Load | nominal 0.1 ... 5 kΩ | |
| Switching frequency | - bus powered: filter OFF: max. 150 Hz, filter ON: max. 15 Hz - loop powered: max. 10 Hz |
|
| Energized/De-energized delay | - bus powered: filter OFF: 1 ms, filter ON: 10 ms - loop powered: switch-on 50 ms, switch-off 6 ms (300 Ω load) |
|
| Line fault detection | ||
| Short-circuit | < 25 Ω | |
| Open-circuit | > 100 kΩ | |
| Test current | < 4 mA | |
| Fault indication output | ||
| Connection | SL1: 6b | |
| Output type | open collector transistor (internal fault bus) | |
| Fault current | 4 mA pulsing (20 ms ON, 200 ms OFF) | |
| Fault level | lead short-circuit detection at < 25 Ω lead breakage detection at > 100 kΩ typical |
|
| Galvanic isolation | ||
| Output/power supply, inputs, and collective error | safe electrical isolation acc. to EN 60079-11: 2007, voltage peak value 375 V | |
| Indicators/settings | ||
| Display elements | LEDs | |
| Control elements | DIP switch | |
| Factory setting | bus powered, input: dry contact, line fault detection enabled | |
| Configuration | via DIP switches | |
| Labeling | space for labeling at the front | |
| Directive conformity | ||
| Electromagnetic compatibility | ||
| Directive 2014/30/EU | EN 61326-1:2013 (industrial locations) | |
| Conformity | ||
| Electromagnetic compatibility | NE 21:2006 For further information see system description. |
|
| Degree of protection | IEC 60529:2001 | |
| Ambient conditions | ||
| Ambient temperature | -20 ... 60 °C (-4 ... 140 °F) | |
| Mechanical specifications | ||
| Degree of protection | IP20 | |
| Mass | approx. 100 g | |
| Dimensions | 12.5 x 106 x 128 mm (0.5 x 4.2 x 5.1 inch) (W x H x D) | |
| Height | 106 mm | |
| Width | 12.5 mm | |
| Depth | 128 mm | |
| Mounting | on termination board | |
| Coding | pin 2 and 3 trimmed For further information see system description. |
|
| Data for application in connection with hazardous areas | ||
| EU-type examination certificate | CESI 10 ATEX 046 | |
| Marking |  II (1)G [Ex ia Ga] IIC II (1)D [Ex ia Da] IIIC I (M1) [Ex ia Ma] I |
|
| Output | Ex ia Ga, Ex ia Da, Ex ia Ma | |
| Voltage | 25.2 V | |
| Current | 93 mA | |
| Power | 586 mW | |
| Supply | ||
| Maximum safe voltage | 253 V AC (Attention! Um is no rated voltage.) | |
| Certificate | KIWA 15 ATEX 0036 X | |
| Marking | II 3G Ex ec IIC T4 Gc |
|
| Directive conformity | ||
| Directive 2014/34/EU | EN 60079-0:2012+A11:2013 , EN 60079-11:2012 , EN 60079-7:2015+A1:2018 | |
| International approvals | ||
| FM approval | ||
| Control drawing | 116-0431 (cFMus) | |
| UL approval | ||
| Control drawing | 116-0383 (cULus) | |
| IECEx approval | ||
| IECEx certificate | IECEx CES 10.0017 IECEx KIWA 15.0018X |
|
| IECEx marking | [Ex ia Ga] IIC, [Ex ia Da] IIIC, [Ex ia Ma] I Ex ec IIC T4 Gc |
|
| General information | ||
| Supplementary information | Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com. | |
Classifications
| System | Classcode |
|---|---|
| ECLASS 13.0 | 27210101 |
| ECLASS 12.0 | 27210190 |
| ECLASS 11.0 | 27210190 |
| ECLASS 10.0.1 | 27210190 |
| ECLASS 9.0 | 27210190 |
| ECLASS 8.0 | 27210190 |
| ECLASS 5.1 | 27210121 |
| ETIM 9.0 | EC001485 |
| ETIM 8.0 | EC001485 |
| ETIM 7.0 | EC001485 |
| ETIM 6.0 | EC001485 |
| ETIM 5.0 | EC001485 |
| UNSPSC 12.1 | 39121008 |
Details: HiC2877
Function
This isolated barrier is used for intrinsic safety applications.
The device supplies power to solenoids, LEDs and audible alarms located in a hazardous area.
It is controlled with a loop powered control signal, switch contact, transistor, or logic signal.
At full load, 11.2 V at 40 mA (with 55 mA current limit) is available for the hazardous area application.
Line fault detection of the field circuit is indicated by a red LED and an output on the fault bus.
This device mounts on a HiC termination board.
Product Documentation: HiC2877
| Product information | Språk | Filtype | Filstørrelse |
|---|---|---|---|
| Application Guideline Solenoid Drivers | ENG | 734 KB | |
| Safety and Security Documentation | |||
| Instruction manual | ENG | 168 KB | |
| Functional Safety Manual | ENG | 1399 KB | |
| Manuals | |||
| System Manual | ENG | 5438 KB | |
Design / Simulation: HiC2877
| CAD | Språk | Filtype | Filstørrelse |
|---|---|---|---|
| CAD 3-D / CAD 3-D | ALL | STP | 2770 KB |
| CAD Portal / CAD Portal | ALL | LINK | --- |
Approvals: HiC2877
Relaterte produkter: HiC2877
| Accessory of | ||||||
|---|---|---|---|---|---|---|
|
||||||
|
||||||
|
||||||
Choose from various selection criteria like safety integrity level, performance level, device function, and signal type and find the SIL/PL assessed device that you are looking for.
Pepperl+Fuchs AS
Frednesøya 21
3933 Porsgrunn
Norway
info@no.pepperl-fuchs.com
+47 3557 3800
© 2024 Med enerett.
Pepperl+Fuchs er en ledende leverandør innen utvikling og produksjon av produkter til det globale automasjonsmarkedet. Kontinuerlig innovasjon, høy kvalitet og kontinuerlig vekst danner grunnlaget for vår kontinuerlige suksess i mer enn 70 år. Pepperl+Fuchs-konsernet har i dag mer enn 6300 ansatte globalt. Produksjonen er basert på ISO 9001 og finner sted i Tyskland, USA, Singapore, Ungarn, Indonesia og Ungarn.