SMART Transmitter Power Supply KCD2-STC-Ex1.ES.SP

1-channel isolated barrier
24 V DC supply (Power Rail)
Input for 2-wire SMART transmitters and current sources
Output for 4 mA ... 20 mA or 1 V ... 5 V
Sink or source mode
Line fault detection (LFD)
Housing width 12.5 mm
Connection via spring terminals with push-in connection technology
Up to SIL 3 acc. to IEC/EN 61508

Technical Data
Details
Informative Literature
Product Documentation
Design / Simulation
Approvals
Relaterte produkter
Spør produktsakkyndige

Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.

Last ned komplett datablad som PDF:

Datablad utdrag: Tekniske data for KCD2-STC-Ex1.ES.SP

General specifications
Signal type		Analog input
Functional safety related parameters
Safety Integrity Level (SIL)		SIL 3
Systematic capability (SC)		SC 3
Supply
Connection		Power Rail or terminals 9+, 10-
Rated voltage		19 ... 30 V DC
Ripple		≤ 10 %
Rated current		≤ 50 mA
Power dissipation		≤ 800 mW
Power consumption		≤ 1.2 W
Input
Connection side		field side
Connection		terminals 1+, 2-; 3+, 4-
Input signal		4 ... 20 mA , limited to approx. 27 mA reverse polarity protected
Line fault detection		downscaling ≤ 3 mA ; upscaling ≥ 22 mA
Voltage drop		approx. 5 V on terminals 3+, 4-
Available voltage		≥ 15 V at 20 mA terminals 1+, 2-
Output
Connection side		control side
Connection		terminals 5-, 6+
Load		0 ... 300 Ω (source mode)
Output signal		source mode: 4 ... 20 mA or 1 ... 5 V (internal resistor: 250 Ω, 0.1 %) sink mode: 4 ... 20 mA, operating voltage 16 ... 28 V For additional internal or external loads the voltage drop has to be considered, e. g. 250 Ω x 20 mA = 5 V.
Ripple		20 mV _rms
Fault indication output
Output type		fault bus signal , open collector transistor
Transfer characteristics
Deviation		at 20 °C (68 °F) ≤ ± 20 µA incl. calibration, linearity, hysteresis, loads and supply voltage fluctuations (source mode and sink mode 4 ... 20 mA) ≤ 10 mV incl. calibration, linearity, hysteresis and fluctuations of supply voltage (source mode 1 ... 5 V)
	Influence of ambient temperature	< 2 µA/K (0 ... 70 °C (32 ... 158 °F)); < 4 µA/K (-20 ... 0 °C (-4 ... 32 °F)) (source mode and sink mode 4 ... 20 mA) < 0.5 mV/K (0 ... 70 °C (32 ... 158 °F)); < 1 mV/K (-20 ... 0 °C (-4 ... 32 °F)) (source mode 1 ... 5 V)
Frequency range		field side into the control side: bandwidth with 1 mA_pp signal 0 ... 3 kHz (-3 dB) control side into the field side: bandwidth with 0.5 V_pp signal 0 ... 3 kHz (-3 dB)
Settling time		≤ 200 ms
Rise time/fall time		≤ 20 ms
Galvanic isolation
Input/Output		safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
Input/power supply		safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
Output/power supply		Basic isolation acc. to EN 61010-1 rated insulation voltage ≤ 50 V
Indicators/settings
Display elements		LEDs
Control elements		DIP switch
Factory setting		output: current source
Configuration		via DIP switches
Labeling		space for labeling at the front
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2013 (industrial locations)
Conformity
Electromagnetic compatibility		NE 21:2017 For further information see system description.
Degree of protection		IEC 60529:2001
Ambient conditions
Ambient temperature		-20 ... 70 °C (-4 ... 158 °F)
Mechanical specifications
Degree of protection		IP20
Connection		spring terminals
Mass		approx. 100 g
Dimensions		12.5 x 119 x 114 mm (0.5 x 4.7 x 4.5 inch) (W x H x D) , housing type A2
	Height	124 mm
	Width	12.5 mm
	Depth	114 mm
Mounting		on 35 mm DIN mounting rail acc. to EN 60715:2001
Data for application in connection with hazardous areas
EU-type examination certificate		CESI 10 ATEX 071
	Marking	II (1)G [Ex ia Ga] IIC II (1)D [Ex ia Da] IIIC I (M1) [Ex ia Ma] I
	Input	Ex ia
Supply
	Maximum safe voltage	253 V AC (Attention! U_m is no rated voltage.)
Equipment		terminals 1+, 2-
	Voltage	25.2 V
	Current	100 mA
	Power	630 mW
	Internal capacitance	5.7 nF
	Internal inductance	negligible
Equipment		terminals 3+, 4-
	Voltage	< 30 V
	Current	< 128 mA
	Voltage	7.2 V
	Current	100 mA
	Power	25 mW
	Internal capacitance	5.7 nF
	Internal inductance	negligible
Certificate		CESI 19 ATEX 005 X
	Marking	II 3G Ex ec IIC T4 Gc
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2012+A11:2013 , EN 60079-11:2012 , EN 60079-7:2015
International approvals
UL approval		E106378
	Control drawing	116-0378 (cULus)
IECEx approval
	IECEx certificate	IECEx CES 11.0001X
	IECEx marking	[Ex ia Ga] IIC , [Ex ia Da] IIIC , [Ex ia Ma] I Ex ec IIC T4 Gc
General information
Supplementary information		Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.

Classifications

System	Classcode
ECLASS 13.0	27210119
ECLASS 12.0	27210119
ECLASS 11.0	27210119
ECLASS 10.0.1	27210119
ECLASS 9.0	27210119
ECLASS 8.0	27210119
ECLASS 5.1	27210119
ETIM 9.0	EC001485
ETIM 8.0	EC001485
ETIM 7.0	EC001485
ETIM 6.0	EC001485
ETIM 5.0	EC001485
UNSPSC 12.1	32101514

Details: KCD2-STC-Ex1.ES.SP

Function

This isolated barrier is used for intrinsic safety applications.

The device supplies 2-wire transmitters in the hazardous area, and can also be used with current sources.

The device transfers the analog input signal to the non-hazardous area as an isolated current value.

Bi-directional communication is supported for SMART transmitters that use current modulation to transmit data and voltage modulation to receive data.

The output is selected as a current source, current sink, or voltage source via DIP switches.

A fault is signalized by LEDs and a separate collective error message output.

Test sockets for the connection of HART communicators are integrated into the terminals of the device.

Informative Literature: KCD2-STC-Ex1.ES.SP

Literature	Språk	Filtype	Filstørrelse
Application Report - Biological Cleaning of Wastwater and Secondary Sedimentation Stage	ENG	PDF	566 KB
Application Report - Energy Generation in Wastwater Treatment Plants	ENG	PDF	532 KB
Application Report - Generating Electricity in Coal-Fired Power Plants	ENG	PDF	412 KB
Application Report - Sand Trap and Preliminary Sedimentation Stage	ENG	PDF	448 KB
Application Report - Screening Systems in Sewage Treatment Plants	ENG	PDF	577 KB
Application Report - Sicherer Brennstofftransport in Kohlekraftwerken	ENG	PDF	391 KB
Application Report - Water Inlet in Wastewater Treatment Plants	ENG	PDF	526 KB

Product Documentation: KCD2-STC-Ex1.ES.SP

Safety and Security Documentation	Språk	Filtype	Filstørrelse
Instruction manual	ENG	PDF	169 KB
Safety Manual	ENG	PDF	427 KB
Manuals
Manual	ENG	PDF	3685 KB

Design / Simulation: KCD2-STC-Ex1.ES.SP

CAD	Språk	Filtype	Filstørrelse
CAD 3-D / CAD 3-D	ALL	STP	3048 KB
CAD Portal / CAD Portal	ALL	LINK	---
CAE
CAE EPLAN Data Portal / CAE EPLAN Data Portal	ALL	LINK	---
CAE EPLAN macro EDZ / CAE EPLAN Makro EDZ	ALL	EDZ	2351 KB

Approvals: KCD2-STC-Ex1.ES.SP

Certificates	Sertifikatnummer	Språk	Filtype	Filstørrelse
China SITIIAS CCC Ex Certificate	2020322316001399 (Singapore)	ALL	PDF	1074 KB
DNV Marine	TAA00001WX	ALL	PDF	106 KB
Europe CESI ATEX Category 3 G	CESI 19 ATEX 005X	ALL	PDF	400 KB
Europe CESI I (M1) II (1) G II (1) D ATEX Category	CESI 10 ATEX 071	ALL	PDF	629 KB
India PESO (India) CCOE	A/P/HQ/KA/104/5873 (P507652)	ALL	PDF	101 KB
South Africa MASC	MASC MS/23-8149X	ALL	PDF	642 KB
TÜV SÜD Functional Safety Certificate	C-IS-204399-01	ALL	PDF	188 KB
USA Canada UL Hazardous Location Certificate of Compliance cULus UL E106378	CoC E106378 RepRef E106378-20130719	ALL	PDF	413 KB
Worldwide CESI IECEx Certificate of Conformity	IECEx CES 11.0001X	ALL	LINK	---
Control Drawings
Control drawing UL / Control drawing UL		ALL	PDF	128 KB
Declaration of Conformity
EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F)	DOC-0297E	ALL	PDF	82 KB

Relaterte produkter: KCD2-STC-Ex1.ES.SP

Matching System Components

	KFD2-EB2 Power Feed Module
	Interface for Power Rail, Supply current ≤ 4 A, Replaceable fuse, Relay contact output, reversible, LED status indicationpa

	UPR-03 Universal Power Rail
	35 mm DIN mounting rail with 3-conductor insert, Provides DC supply voltage to all equipped K-System modules, Standard length 2 m (6 foot), simple to customize to application space, Eliminates daisy-chainspa

	UPR-03-S Universal Power Rail
	35 mm DIN mounting rail with 3-conductor insert, Provides DC supply voltage to all equipped K-System modules, Standard length 0.8 m (2.6 ft), simple to customize to application space, Eliminates daisy-chainspa

	UPR-03-M Universal Power Rail
	35 mm DIN mounting rail with 3-conductor insert, Provides DC supply voltage to all equipped K-System modules, Standard length 1.6 m (5 foot), simple to customize to application space, Eliminates daisy-chainspa

	K-DUCT-BU Profile Rail
	Cable trunking is integrated in the mounting profile, Safe spacious separation of safe and hazardous signals, No additional cable guides necessary, Standard length 1.8 m (5.8 ft), simple to customize to application space, With mounting aidspa

	K-DUCT-BU-UPR-03 Profile Rail
	Cable trunking with integrated Power Rail UPR-03, Safe spacious separation of safe and hazardous signals, No additional cable guides necessary, Provides DC supply voltage to all equipped K-System modules, Standard length 1.8 m (5.8 ft), simple to customize to application space, With end caps UPR-E, cover and mounting aidspa

Accessories

	KC-CTT-3GN2BU Terminal Block with Test Plug Socket
	2-pin spring terminal with push-in connection technology, For KC modules of K-System, Integrated test sockets for connection of HART communicators, Packaging unit: 3 pieces green, 2 pieces bluepa

	KC-CTT-5BU Terminal Block with Test Plug Socket
	2-pin spring terminal with push-in connection technology, For KC modules of K-System, Integrated test sockets for connection of HART communicators, Packaging unit: 5 pieces bluepa

	KC-CTT-5GN Terminal Block with Test Plug Socket
	2-pin spring terminal with push-in connection technology, For KC modules of K-System, Integrated test sockets for connection of HART communicators, Packaging unit: 5 pieces greenpa

	KF-CP Coding Pins
	Coding of K-System terminal blocks, Coding of LB/FB-System front sockets, Packaging unit: 20 x 6 coding pinspa

Generelle merknader relatert til produktinformasjon fra Pepperl+Fuchs

Snarveier

Selector for Safety Products

Choose from various selection criteria like safety integrity level, performance level, device function, and signal type and find the SIL/PL assessed device that you are looking for.

Pepperl+Fuchs AS
Frednesøya 21
3933 Porsgrunn
Norway
info@no.pepperl-fuchs.com
phone +47 3557 3800

Pepperl+Fuchs er en ledende leverandør innen utvikling og produksjon av produkter til det globale automasjonsmarkedet. Kontinuerlig innovasjon, høy kvalitet og kontinuerlig vekst danner grunnlaget for vår kontinuerlige suksess i mer enn 70 år. Pepperl+Fuchs-konsernet har i dag mer enn 6300 ansatte globalt. Produksjonen er basert på ISO 9001 og finner sted i Tyskland, USA, Singapore, Ungarn, Indonesia og Ungarn.