VIM32PP-E7DC8-0RE-IO-1V1401 Vibration sensor

Panoramica dei principali vantaggi

Raw data for vibration acceleration a-Raw by means of BLOB transfer
Frequency range up to 12 kHz with sampling rate up to 64 kHz
Bearing status parameter according to DIN ISO 13373
Vibration velocity in mm/s (rms) acc. to DIN ISO 10816/20816
Vibration acceleration in g (rms) acc. to DIN ISO 10816/20816
Additional temperature value output
IO-Link Interface for process data, parameterization and diagnosis
Rugged stainless steel housing

Mostra di più

Product photo: Vibration sensor VIM32PP-E7DC8-0RE-IO-1V1401

Nota

Tutti i documenti relativi ai prodotti, come ad esempio certificati, dichiarazioni di conformità ecc., pubblicati prima della conversione con il nome Pepperl+Fuchs GmbH o Pepperl+Fuchs AG, si applicano anche a Pepperl+Fuchs SE.

Scheda tecnica Funzione Classificazione Informative Literature Product Documentation Design / Simulation Certificazioni Software Prodotto correlati

Dati tecnici di VIM32PP-E7DC8-0RE-IO-1V1401

Vibration sensor with IO-Link and programmable switching output or analog current output

Type

Vibration sensor

Measuring technology

MEMS capacitive

Series

Performance Plus Line

Measured variable

Vibration velocity
Vibration acceleration
Bearing status parameter
Crest factor
Temperature

Measuring range

Vibration velocity	v-rms	0 ... 128 mm/s
Vibration acceleration	a-rms	0 ... 34 g rms
Vibration acceleration	a-Peak	0 ... 48 g peak value per 1 s
Vibration acceleration	a-Raw	-48 ... 48 g by means of BLOB transfer
Bearing status parameter		1 ... 4 see section characteristic curve
Crest factor		0 ... 100
Temperature		-40 ... 85 °C (-40 ... 185 °F)

Measurement accuracy

Vibration velocity: ± 0.1 mm/s (calibration point: 90% of the measuring range; 159.2 Hz) Complies with the tolerance requirements of DIN ISO 2954 for measuring range greater than 8 mm/s
Vibration acceleration: ± 0.01 g (calibration point: 90% of the measuring range; 159.2 Hz) Complies with the tolerance requirements of DIN ISO 2954

Cross-sensitivity

< 5 % of the partial lateral acceleration, which acts exactly 90° to the measuring axis

Resolution

Vibration velocity: 0.01 mm/s
Vibration acceleration: 0.01 g
Bearing status parameter: 0.01

Frequency range

Vibration acceleration a-raw: 1 ... 12 kHz , by means of BLOB transfer
Vibration velocity rms: 10 ... 1000 Hz , acc. to DIN ISO 10816/20816 , programmable
Vibration acceleration rms: 1 ... 1000 Hz , acc. to DIN ISO 10816/20816 , programmable
Vibration acceleration a-peak: 10 ... 10 kHz
Crest factor: 10 ... 10 kHz
Bearing status parameter: 10 ... 10 kHz , acc. to DIN ISO 13373-3

Averaging time

for v-rms: 2 s
for a-rms: 2 s

Sampling rate

Vibration acceleration a-raw: 64 kHz , programmable
Vibration velocity rms: 8 Hz
Vibration acceleration rms: 8 kHz
Vibration acceleration a-peak: 32 Hz
Crest factor: 32 Hz
Bearing status parameter: 32 kHz

MTTF_d		329 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %

Fusing		external fuse is required: 1 A , fast acting , 30 V DC
Operating voltage	U_B	18 ... 30 V DC
Current consumption		max. 320 mA
Power consumption	P₀	max. 10 W
Time delay before availability	t_v	≤ 3.6 s
Surge protection		up to 2 kV

Interface type		IO-Link (via C/Q = Pin 4)
IO-Link revision		1.1
Device profile		Identification and Diagnosis - I&D , BLOB transfer
Process data		Input 24 Byte measurement channels: -rms value velocity - peak value acceleration - rms value acceleration - temperature - crest factor - bearing status parameter per measurement channel: - measurement value 2 Byte - scaling 8 Bit - switching signals 2 Bit status data
Vendor ID		1 (0x0001)
Device ID		5308673 (0x510101)
Transfer rate		COM3 (230.4 kbits/s)
Min. cycle time		3.8 ms
SIO mode support		yes
Compatible master port type		Class A Class B (use 3-pole adapter or 3-wire cable)
BLOB size		1.28 MByte , programmable
BLOB segments		200 Byte per request and BLOB segment respectively

Output type		C/Q - Pin 4 in SIO mode (switching signal of the measured variable is programmable)
Switching function		Normally open/closed (NO/NC)
Operating current		≤ 100 mA
Short-circuit protection		yes

Output type		I/Q - pin 2 (parameterizable as analog current output or switching signal) - I: analog output for the measured variable, current 4 ... 20 mA - Q: switching signal of the measured variable is parameterizable, PNP normally open
Switching function		Normally open/closed (NO/NC)
Operating current		≤ 120 mA for switching signal
Voltage drop		< 2 V
Output current		4 ... 20 mA at analog output
Load resistor		≤ 500 Ω at analog output
Short-circuit protection		yes

Degree of protection		DIN EN 60529, IP66, IP67
Shock resistance		DIN EN 60068-2-27, 60 g, 6 ms
Vibration resistance		DIN EN 60068-2-6, 16.5 g, 10 ... 12000 Hz
Vibration evaluation		DIN ISO 10816/20816 , DIN ISO 13373-3

UL approval

Ordinary Location		E468231 cULus Listed, Class III Power Source and limited energy , if UL marking is marked on the product. For use in NFPA 70 Applications only. adapters providing field wiring on request
Maximum permissible ambient temperature		max. 80 °C (max. 176 °F)

Ambient temperature		-40 ... 85 °C (-40 ... 185 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)

Connection type

plug

Housing material

Stainless steel 1.4305 / AISI 303

Degree of protection

IP66 / IP67 only in connected state

Connector

Threading		M12
Number of pins		4

Mass

approx. 100 g

Dimensions

Length		72.5 mm
Diameter		23.8 mm

Note generali

We value your privacy!

We and our partners are using technologies like cookies and process personal data like the IP-address or browser information in order to personalize the advertising that you see. This helps us to show you more relevant ads and improves your internet experience. We also use it in order to measure results or align our website content. Because we value your privacy, we are herewith asking for your permission to use these technologies. You can always change/withdraw your consent later by clicking on the settings button on the left lower corner of the page.

Categories	Description	Status
Functional	These cookies are necessary so that you can navigate through the pages and use essential functions (e.g. login).
Analytics	We use these cookies and scripts to measure the visits and clicks on our website in order to constantly improve it.
Marketing	These cookies and similar technologies are used to provide you with personalized and therefore relevant advertising content.