UDC-30GS-3EP1-IO-0,2M-V19 Double sheet sensor

Panoramica dei principali vantaggi

Ultrasonic system for reliable detection of no, one, or two overlapping sheet materials
Insensitive to printing, colors, and shining surfaces
Perpendicular or inclined sensor mounting relative to the sheet plane possible
Integrated alignment aid
IO-Link Interface for process data, parameterization and diagnosis
Synchronization options
No teach-in required

Mostra di più

Product photo: Double sheet sensor UDC-30GS-3EP1-IO-0,2M-V19

Dimensions: Double sheet sensor UDC-30GS-3EP1-IO-0,2M-V19

Nota

Tutti i documenti relativi ai prodotti, come ad esempio certificati, dichiarazioni di conformità ecc., pubblicati prima della conversione con il nome Pepperl+Fuchs GmbH o Pepperl+Fuchs AG, si applicano anche a Pepperl+Fuchs SE.

Scheda tecnica Funzione Classificazione Product Documentation Design / Simulation Certificazioni Software Prodotto correlati

Dati tecnici di UDC-30GS-3EP1-IO-0,2M-V19

Sensing range		50 ... 150 mm , optimal distance: 80 mm
Transducer frequency		approx. 85 kHz

Non-volatile memory		EEPROM
Write cycles		300000

LED green		indication: single sheet detected flashing (1 Hz) - standby mode flashing with short break (1 Hz) - IO-Link mode
LED yellow		indication: no sheet detected (Air)
LED red		indication: double sheet detected flashing: device error

Operating voltage	U_B	18 ... 30 V DC , ripple 10 %_SS
No-load supply current	I₀	≤ 100 mA
Power consumption	P₀	≤ 1500 mW
Time delay before availability	t_v	≤ 300 ms

Interface type		IO-Link
IO-Link revision		1.1
Device profile		Identification and Diagnosis - I&D
Process data		Input: 16 Bit - measurement value 8 Bit - selected threshold set 2 Bit - switching signals 3 Bit Output: 8 Bit - threshold set 2 Bit - disable transducer 1 Bit
Vendor ID		1 (0x0001)
Device ID		3148291 (0x300A03)
Transfer rate		COM1 (4.8 kbits/s)
Min. cycle time		22.4 ms
SIO mode support		yes
Compatible master port type		Class A (use adapter cable listed in accesories) Class B (use 3-pole adapter or 3-wire cable)

Designation

SYNC

Input/output type

1 synchronization connection, bidirectional

0 Level		0 ... 1 V
1 Level		2.5 V ... U_B
Input impedance		> 22 kΩ
Output rated operating current		current source < 2.5 mA
Pulse length		0.4 ... 6 ms with external control, low active

Synchronization frequency

Common mode operation		≤ 140 Hz
Multiplex operation		≤ 140 Hz /n, n = number of sensors , n ≤ 10

Designation

IN2/FEEDBACK

Input/output type

input or output programmable via IO-Link :
input for selection of a threshold set (factory default)
output as feedback output

Input type

digital input

Signal		0-level: 0 ... + 1V 1-level: +U_B - 1 V ... +U_B
Input impedance		≥ 60 kΩ
Pulse length		≥ 100 ms

Output type

PNP

Rated operating current	I_e	8 mA
Voltage drop		< 3 V
Fusing		reverse polarity protected , overload and short-circuit protected

Designation		IN1/TEACH
Input type		0-level: 0 ... + 1V 1-level: +U_B - 1 V ... +U_B
Pulse length		≥ 100 ms
Impedance		≥ 60 kΩ

Designation		OUT 1 ... 3
Number		3
Output function		OUT 1: single sheet detected OUT 2: double sheet detected OUT 3: no sheet detected (air)
Output type		Push-pull (4 in 1) output , NC contact ( programmable )
Rated operating current	I_e	100 mA per output
Voltage drop	U_d	≤ 3 V
Switch-on delay	t_on	30 ms (programmable)
Switch-off delay	t_off	30 ms (programmable)
Pulse extension		can be activated (100 ms or IO-Link cycle time)
Fusing		reverse polarity protected , overload and short-circuit resistant

Standard conformity

Standards

EN IEC 60947-5-2:2020
IEC 60947-5-2:2019
IEC 61131-9 / IO-Link V1.1.3

UL approval		cULus Listed, General Purpose, Class 2 Power Source
CCC approval		CCC approval / marking not required for products rated ≤36 V

Ambient temperature		0 ... 60 °C (32 ... 140 °F)
Storage temperature		-25 ... 70 °C (-13 ... 158 °F)

Connection type

fixed cable with plug

Housing length

Ultrasonic transmitter		56 mm
Ultrasonic receiver		78 mm

Housing diameter

Ultrasonic transmitter		30 mm
Ultrasonic receiver		30 mm

Degree of protection

IP65

Material

Housing		Stainless steel 1.4305/AISI 303, polyamide plastic parts
Transducer		epoxy resin/hollow glass sphere mixture; polyurethane foam

Connector

Threading		M12 x 1
Number of pins		8

Cable

Cable diameter		4.3 mm
Bending radius		5 x diameter , fixed installation
Material		PUR
Color		black
Length	L	approx. 200 mm

Mass

300 g

Tightening torque, fastening screws

max. 30 Nm

Note generali

We value your privacy!

We and our partners are using technologies like cookies and process personal data like the IP-address or browser information in order to personalize the advertising that you see. This helps us to show you more relevant ads and improves your internet experience. We also use it in order to measure results or align our website content. Because we value your privacy, we are herewith asking for your permission to use these technologies. You can always change/withdraw your consent later by clicking on the settings button on the left lower corner of the page.

Categories	Description	Status
Functional	These cookies are necessary so that you can navigate through the pages and use essential functions (e.g. login).
Analytics	We use these cookies and scripts to measure the visits and clicks on our website in order to constantly improve it.
Marketing	These cookies and similar technologies are used to provide you with personalized and therefore relevant advertising content.