Com Unit for FOUNDATION Fieldbus Modular I/O FB8210*
- Interface between the I/O modules and the PCS/PLC
- Com unit for 20 analog or 40 digital channels
- Communication via FOUNDATION Fieldbus H1
- HART communication via service bus
- Configured via the process control system
- Non-volatile memory for configuration and parameter settings
- Quick communication set-up
- Permanently self-monitoring
- Outputs drive to safe state in case of failures
- Supports multichannel I/O modules
- Installation in suitable enclosures in Zone 1 or Zone 21
- Module can be exchanged under voltage (hot swap)
- Installation in suitable enclosures in Zone 1
Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.
Last ned komplett datablad som PDF:
Datablad utdrag: Tekniske data for FB8210*
| Supply | ||
|---|---|---|
| Connection | backplane bus | |
| Rated voltage | 5 V DC , only in connection with the power supplies FB92** | |
| Power consumption | 2 W | |
| Auxiliary energy | 24 V DC Trunk load 20 mA |
|
| Fieldbus connection | ||
| Fieldbus type | FOUNDATION Fieldbus H1 | |
| FOUNDATION Fieldbus | ||
| Connection | wired to Ex e terminals via backplane | |
| Baud rate | 31.25 kBit/s , MBP | |
| Protocol | H1 to IEC 1158-2 | |
| Station connection | directly at the trunk or via spur protector | |
| Number of stations per bus line | 1 or 2, depending on the required response times | |
| Number of channels per station | max. 20 analog, max. 40 digital | |
| Supported I/O modules | 5 slots, to be filled with (combinations possible): 1*08 digital input, 8-channel, NAMUR 3*05 analog input, 4-channel, 20 mA (HART via service bus) 4*05 analog output, 4-channel, 20 mA (HART via service bus) 5204 Pt100 RTD input, 4-channel 5205 thermocouple input, 4-channel 6305 relay output, 4-channel, 230 V 6306 relay output, 8-channel, 24 V 6*08 digital output, 8-channel, Ex i 6210-6215 digital output, 4-channel, Ex i power * = variable (2=IS, 3=Ex e) |
|
| Bus length | max. 1900 m (must not be exceeded by the sum of all trunk and spur lines) |
|
| Spur length | max. 120 m (depending on the number of field devices. Modular I/O station = 1 field device) |
|
| Addressing | via PCS (software) | |
| Internal bus | ||
| Connection | backplane bus | |
| Indicators/settings | ||
| LED indicator | LED green (power supply): On = operating, fast flash = cold start LED red (collective alarm): On = internal fault, flashing = no fieldbus LED yellow (operating mode): Flashing = active |
|
| Directive conformity | ||
| Electromagnetic compatibility | ||
| Directive 2014/30/EU | EN 61326-1 | |
| Conformity | ||
| Electromagnetic compatibility | NE 21 | |
| Degree of protection | IEC 60529 | |
| Ambient conditions | ||
| Ambient temperature | -20 ... 60 °C (-4 ... 140 °F) | |
| Storage temperature | -25 ... 85 °C (-13 ... 185 °F) | |
| Relative humidity | 95 % non-condensing | |
| Shock resistance | shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18 | |
| Vibration resistance | frequency range 10 ... 150 Hz; transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g; 10 cycles frequency range 5 ... 100 Hz; transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g; 90 minutes at each resonance |
|
| Damaging gas | designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3 | |
| Mechanical specifications | ||
| Degree of protection | IP20 (module) , a separate housing is required acc. to the system description | |
| Connection | via backplane | |
| Mass | approx. 750 g | |
| Dimensions | 57 x 107 x 132 mm (2.2 x 4.2 x 5.2 inch) | |
| Data for application in connection with hazardous areas | ||
| EU-Type Examination Certificate | PTB 97 ATEX 1074 U | |
| Marking |  II 2 G Ex d IIC Gb |
|
| Directive conformity | ||
| Directive 2014/34/EU | EN 60079-0:2009 EN 60079-1:2007 EN 60079-11:2007 EN 60079-26:2007 EN 61241-11:2006 |
|
| International approvals | ||
| ATEX approval | PTB 97 ATEX 1075 |
|
| EAC approval | Russia: RU C-IT.MIII06.B.00129 | |
| Marine approval | ||
| Lloyd Register | 15/20021 | |
| DNV GL Marine | TAA0000034 | |
| American Bureau of Shipping | T1450280/UN | |
| Bureau Veritas Marine | 22449/B0 BV | |
Classifications
| System | Classcode |
|---|---|
| ECLASS 13.0 | 27210121 |
| ECLASS 12.0 | 27210121 |
| ECLASS 11.0 | 27210121 |
| ECLASS 10.0.1 | 27210121 |
| ECLASS 9.0 | 27210121 |
| ECLASS 8.0 | 27210121 |
| ECLASS 5.1 | 27210121 |
| ETIM 9.0 | EC001485 |
| ETIM 8.0 | EC001485 |
| ETIM 7.0 | EC001485 |
| ETIM 6.0 | EC001485 |
| ETIM 5.0 | EC001485 |
| UNSPSC 12.1 | 39121008 |
Details: FB8210*
Function
The FOUNDATION Fieldbus com unit forms the interface between the I/O modules on the backplane and the process control system.
It supports only dual width I/O modules. Thereby signals from NAMUR sensors, mechanical contacts, high-power solenoid drivers, power relays, sounders, and alarm LEDs are transported to the higher-level bus system.
The com unit can be easily configured via DTM and supports HART.
Informative Literature: FB8210*
| Literature | Språk | Filtype | Filstørrelse |
|---|---|---|---|
| Application Report - Communication Redundancy for Uninterrupted Operation | ENG | 529 KB | |
| Application Report - LB and FB Remote I/O Systems for Digitally Connecting Analog Field Devices | ENG | 208 KB | |
| Application Report - Space Saving Extension for Existing Plants | ENG | 300 KB | |
| Application Report - Using Remote I/O Systems for the Efficient Digitalization of Plants | ENG | 371 KB |
Product Documentation: FB8210*
| System Descriptions | Språk | Filtype | Filstørrelse |
|---|---|---|---|
| Supported I/O modules | ENG | 31 KB | |
| Safety and Security Documentation | |||
| Instruction manual | ENG | 51 KB | |
| Manuals | |||
| Manual - FB-Remote-I/O-System | ENG | 5670 KB | |
| Manual FF ComUnit 8x10 | ENG | 1471 KB | |
| Software Information | |||
| Software Product Note Remote I/O DTM / Softwareproduktschein Remote I/O DTM | ALL | 256 KB | |
Design / Simulation: FB8210*
| CAE | Språk | Filtype | Filstørrelse |
|---|---|---|---|
| CAE EPLAN Data Portal / CAE EPLAN Data Portal | ALL | LINK | --- |
| CAE EPLAN macro EDZ / CAE EPLAN Makro EDZ | ALL | EDZ | 103 KB |
Approvals: FB8210*
| Certificates | Sertifikatnummer | Språk | Filtype | Filstørrelse |
|---|---|---|---|---|
| Bureau Veritas (Maritime) Marine | 22449/C0 BV | ALL | 590 KB | |
| DNV Marine | TAA0000034 | ALL | 110 KB | |
| Europe PTB ATEX Category 2 G | PTB 97 ATEX 1074U | ALL | 2619 KB | |
| Lloyd's Register Marine | LR2003616TA-02 | ALL | 557 KB | |
| Worldwide Fieldbus Foundation | IT048400 | ALL | 149 KB |
Software: FB8210*
| Device Description Files/Drivers | Frigivelsesinfo | Filtype | Filstørrelse |
|---|---|---|---|
| DD & CFF Datei für LB/FB FF Remote IO / DD & CFF Datei für LB/FB FF Remote IO | 39/2007 | ZIP | 65 KB |
Relaterte produkter: FB8210*
| Accessories | ||||||
|---|---|---|---|---|---|---|
|
||||||
Pepperl+Fuchs AS
Frednesøya 21
3933 Porsgrunn
Norway
info@no.pepperl-fuchs.com
+47 3557 3800
© 2024 Med enerett.
Pepperl+Fuchs er en ledende leverandør innen utvikling og produksjon av produkter til det globale automasjonsmarkedet. Kontinuerlig innovasjon, høy kvalitet og kontinuerlig vekst danner grunnlaget for vår kontinuerlige suksess i mer enn 70 år. Pepperl+Fuchs-konsernet har i dag mer enn 6300 ansatte globalt. Produksjonen er basert på ISO 9001 og finner sted i Tyskland, USA, Singapore, Ungarn, Indonesia og Ungarn.