Diffuse mode sensor WTS10-12-4016/103/105
- Specifically for quality checks on welding caps
- Upper and lower welding caps checked simultaneously
- High position and angle tolerance insensitivity of the welding cap
- Stability alarm indication
- Scratch resistant mineral glass lens
Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.
Last ned komplett datablad som PDF:
Datablad utdrag: Tekniske data for WTS10-12-4016/103/105
| Produktbeskrivelse |
|---|
| Diffuse mode sensor |
| General specifications | ||
|---|---|---|
| Detection range | 2 ... 12 mm | |
| Reference target | Copper welding-electrode Diameter: 16 mm , Front end: 6 mm | |
| Light source | LED | |
| Light type | modulated visible red light , 640 nm | |
| Ambient light limit | continuous light 40000 Lux , Modulated light 5000 Lux | |
| Tilting angle | ± 1.5 ° | |
| Position tolerance | ± 2 mm | |
| Indicators/operating means | ||
| Operation indicator | LED green: Power on | |
| Function indicator | LED yellow: switching state LED red: Stability alarm indicator |
|
| Teach-in indicator | LED, green/yellow flashing (approx. 4 Hz) Teach Error:LED green/yellow non equiphase flashing; 8.0 Hz |
|
| Control elements | Teach-In key | |
| Electrical specifications | ||
| Operating voltage | 10 ... 30 V DC | |
| No-load supply current | ≤ 70 mA | |
| Input | ||
| Function input | Enable keys (EK) | |
| Output | ||
| Switching type | light-on | |
| Signal output | switching output PNP NO contact AND logic coupling of both sensor channels short-circuit protected reverse polarity protected | |
| Switching current | max. 100 mA | |
| Switching frequency | 100 Hz | |
| Response time | 5 ms | |
| Conformity | ||
| Product standard | EN 60947-5-2 | |
| Compliance with standards and directives | ||
| Standard conformity | ||
| Shock and impact resistance | IEC / EN 60068. half-sine, 50 g in each X, Y and Z directions | |
| Vibration resistance | IEC / EN 60068-2-6. Sinus. 10 -150 Hz, 5 g in each X, Y and Z directions | |
| Approvals and certificates | ||
| Protection class | II, rated voltage ≤ 250 V AC with pollution degree 1-2 according to IEC 60664-1 | |
| UL approval | cULus Listed | |
| CCC approval | CCC approval / marking not required for products rated ≤36 V | |
| Ambient conditions | ||
| Ambient temperature | 0 ... 50 °C (32 ... 122 °F) The switching accuracy will remain, if the temperature after Teach-In does not varies more than ±7 °C |
|
| Storage temperature | -20 ... 70 °C (-4 ... 158 °F) | |
| Mechanical specifications | ||
| Degree of protection | IP67 | |
| Connection | 5-pin, M12 x 1 connector | |
| Material | ||
| Housing | PC + ABS | |
| Optical face | Scratch resistant mineral glass lens | |
| Mass | 80 g | |
Classifications
| System | Classcode |
|---|---|
| ECLASS 13.0 | 27270903 |
| ECLASS 12.0 | 27270903 |
| ECLASS 11.0 | 27270903 |
| ECLASS 10.0.1 | 27270903 |
| ECLASS 9.0 | 27270903 |
| ECLASS 8.0 | 27270903 |
| ECLASS 5.1 | 27270903 |
| ETIM 9.0 | EC001821 |
| ETIM 8.0 | EC001821 |
| ETIM 7.0 | EC001821 |
| ETIM 6.0 | EC001821 |
| ETIM 5.0 | EC001821 |
| UNSPSC 12.1 | 39121528 |
Details: WTS10-12-4016/103/105
Function
The welding tip sensor WTS10 series is a contrast evaluation sensor with a large and homogeneous light spot fitted to check the quality of the welding cap's face after milling of the welding tip and which is widely used for industrial welding robots.
After the milling process of the welding cap, both tips of the welding gun are inspected and defects such as inclusions, faulty milling or burrs are detected.
Simultaneous control of the quality of both welding tip caps with one sensor is possible by providing two optical outputs on either side of the sensor housing.
The WTS10 features an extended detection area of 11 mm diameter, an uniform lightspot over the full sensing range due to coaxial optics beam path, a new display concept, high switching accuracy, a homogenous light spot and improved position and tilting angle tolerance.
Product Documentation: WTS10-12-4016/103/105
| Brief Instructions | Språk | Filtype | Filstørrelse |
|---|---|---|---|
| Instruction leaflet / Beipackzettel | ALL | 527 KB |
Design / Simulation: WTS10-12-4016/103/105
| CAD | Språk | Filtype | Filstørrelse |
|---|---|---|---|
| CAD 3-D / CAD 3-D | ALL | STP | 1366 KB |
| CAD Portal / CAD Portal | ALL | LINK | --- |
Approvals: WTS10-12-4016/103/105
| Declaration of Conformity | Sertifikatnummer | Språk | Filtype | Filstørrelse |
|---|---|---|---|---|
| EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F) | DOC-2236C | ALL | 226 KB | |
| UK Declaration of Conformity (P+F) / UK-Konformitäterklärung (P+F) | DOC-6936 | ALL | 223 KB |
Relaterte produkter: WTS10-12-4016/103/105
| Accessories | ||||||
|---|---|---|---|---|---|---|
|
||||||
|
||||||
|
||||||
|
||||||
For første gang er en konsekvent løsningsserie med fotoelektriske funksjonsprinsipper og innovative teknologier tilgjengelig i identiske kapslinger. Brukere drar fordel av et uniformt driftskonsept over hele porteføljen. Oppdag seriene R100, R101, R103, R200 og R201 ...
Uansett om det er glass, silisiumskiver eller kretskort: Fotocellene i ML100-serien er spesiallaget for å oppfylle kravene til komplekse registreringsoppgaver. Lær mer om porteføljen ...
Pepperl+Fuchs AS
Frednesøya 21
3933 Porsgrunn
Norway
info@no.pepperl-fuchs.com
+47 3557 3800
Pepperl+Fuchs er en ledende leverandør innen utvikling og produksjon av produkter til det globale automasjonsmarkedet. Kontinuerlig innovasjon, høy kvalitet og kontinuerlig vekst danner grunnlaget for vår kontinuerlige suksess i mer enn 70 år. Pepperl+Fuchs-konsernet har i dag mer enn 6300 ansatte globalt. Produksjonen er basert på ISO 9001 og finner sted i Tyskland, USA, Singapore, Ungarn, Indonesia og Ungarn.