Temperature Converter with Trip Values KFD2-GUT-Ex1.D

1-channel isolated barrier
24 V DC supply (Power Rail)
Thermocouple, RTD, potentiometer or voltage input
Redundant TC input
Current output 0/4 mA ... 20 mA
2 relay contact outputs
Configurable by PACTware or keypad
Line fault (LFD) and sensor burnout detection
Up to SIL 2 acc. to IEC/EN 61508 / IEC/EN 61511

Technical Data
Details
Informative Literature
Product Documentation
Design / Simulation
Approvals
Software
Produkty powiązane

Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.

Pobierz pełną kartę katalogową w formie pliku PDF:

Dane techniczne KFD2-GUT-Ex1.D

General specifications
Signal type		Analog input
Functional safety related parameters
Safety Integrity Level (SIL)		SIL 2
Supply
Connection		terminals 23+, 24- or power feed module/Power Rail
Rated voltage		20 ... 30 V DC
Rated current		approx. 100 mA
Power dissipation/power consumption		≤ 2 W / 2.2 W
Interface
Programming interface		programming socket
Input
Connection side		field side
Connection		terminals 1, 2, 3, 4, 6
RTD		Pt100, Pt500, Pt1000, Ni100, Ni1000
	Types of measuring	2-, 3-, 4-wire technology
	Lead resistance	max. 50 Ω
	Measurement loop monitoring	sensor breakage, sensor short-circuit
Thermocouples		type B, E, J, K, L, N, R, S, T (IEC 584-1: 1995)
	Cold junction compensation	external and internal
	Measurement loop monitoring	sensor breakage
Potentiometer		0.8 ... 20 kΩ
	Types of measuring	2-, 3-, 5-wire technology
Voltage		0 ... 10 V , 2 ... 10 V , 0 ... 1 V , -100 ... 100 mV
Input resistance		≥ 250 kΩ (0 ... 10 V) min. 1 MΩ (0 ... 1 V, -100 ... 100 mV)
Measuring current		approx. 400 µA with resistance measuring sensor
Output
Connection side		control side
Connection		output I: terminals 10, 11, 12 output II: terminals 16, 17, 18 output III: terminals 8+, 7-
Output I, II		relay
	Contact loading	250 V AC / 2 A / cos φ ≥ 0.7 ; 40 DC / 2 A
	Mechanical life	5 x 10⁷ switching cycles
	Energized/De-energized delay	approx. 20 ms / approx. 20 ms
Output III		Analog current output
	Current range	0 ... 20 mA or 4 ... 20 mA
	Open loop voltage	max. 24 V DC
	Load	max. 650 Ω
	Fault signal	downscale I ≤ 3.6 mA, upscale I ≥ 21 mA (acc. NAMUR NE43)
Collective error message		Power Rail
Transfer characteristics
Deviation
	Temperature effect	Input: 0.005 %/K (50 ppm) of span ; current output: 0.005 %/K (50 ppm) of span
	RTD	max. 0.2 % of span
	Thermocouples	max. 10µV deviation of CJC: ±0.8 K
	Voltage	0.1 % of span
	Potentiometer	0.1 % of span when < 5 kΩ 0.5 % of span when > 5 kΩ
	Current output	max. 20 µA
Sampling rate		approx. 700 ms
Galvanic isolation
Input/Other circuits		reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 V_eff
Output I, II against eachother		reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 V_eff
Output I, II/other circuits		reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 V_eff
Output III/power supply and collective error		reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 V_eff
Interface/power supply		reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 V_eff
Indicators/settings
Display elements		LEDs , display
Control elements		Control panel
Configuration		via operating buttons via PACTware
Labeling		space for labeling at the front
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2013 (industrial locations)
Low voltage
	Directive 2014/35/EU	EN 61010-1:2010
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2001
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Mechanical specifications
Degree of protection		IP20
Connection		screw terminals
Mass		300 g
Dimensions		40 x 119 x 115 mm (1.6 x 4.7 x 4.5 inch) (W x H x D) , housing type C2
	Height	119 mm
	Width	40 mm
	Depth	115 mm
Mounting		on 35 mm DIN mounting rail acc. to EN 60715:2001
Data for application in connection with hazardous areas
EU-type examination certificate		TÜV 03 ATEX 2140
	Marking	II (1)G [Ex ia Ga] IIC II (1)D [Ex ia Da] IIIC I (M1) [Ex ia Ma] I
	Input	Ex ia
Supply
	Maximum safe voltage	40 V DC (Attention! The rated voltage can be lower.)
Input		terminals 2, 6 (for active equipment)
	Voltage	13.1 V
	Current	8 mA
	Power	67 mW
	Voltage	29 V
	Current	11 mA
	Power	200 mW
Inputs		terminals 1, 2, 3, 4, 6 (for passive equipment)
	Voltage U_o	13.1 V
	Current I_o	21 mA
	Power P_o	67 mW
Analog output
	Maximum safe voltage	40 V (Attention! The rated voltage can be lower.)
Interface
	Maximum safe voltage	40 V (Attention! The rated voltage can be lower.) , RS 232
Certificate		PF 08 CERT 1213 X
	Marking	II 3G Ex nA nC IIC T4 Gc
Output I, II
	Contact loading	50 V AC/2 A/cos φ > 0.7; 40 V DC/1 A resistive load
Galvanic isolation
	Input/Other circuits	safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN IEC 60079-0:2018+AC:2020 , EN 60079-11:2012 , EN 60079-15:2010
International approvals
IECEx approval
	IECEx certificate	IECEx TUN 09.0019
	IECEx marking	[Ex ia Ga] IIC , [Ex ia Da] IIIC , [Ex ia Ma] I
General information
Supplementary information		Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.

Classifications

System	Classcode
ECLASS 13.0	27210129
ECLASS 12.0	27210129
ECLASS 11.0	27210129
ECLASS 10.0.1	27210129
ECLASS 9.0	27210129
ECLASS 8.0	27210190
ECLASS 5.1	27210107
ETIM 9.0	EC002919
ETIM 8.0	EC002919
ETIM 7.0	EC002919
ETIM 6.0	EC002919
ETIM 5.0	EC001485
UNSPSC 12.1	32101514

Details: KFD2-GUT-Ex1.D

Function

This isolated barrier is used for intrinsic safety applications.

The device converts the signal of a resistance thermometer, thermocouple, potentiometer, or voltage source to a proportional output current. It also provides a relay trip value.

The removable terminal block K-CJC-** is available as an accessory for internal cold junction compensation of thermocouples.

A fault is signalized by LEDs acc. to NAMUR NE44 and a separate collective error message output.

The device is easily configured by the use of the PACTware configuration software.

For additional information, refer to the manual and www.pepperl-fuchs.com.

Informative Literature: KFD2-GUT-Ex1.D

Literature	Język	Typ pliku	Rozmiar pliku
Application Report - Biological Cleaning of Wastwater and Secondary Sedimentation Stage	ENG	PDF	566 KB
Application Report - Energy Generation in Wastwater Treatment Plants	ENG	PDF	532 KB
Application Report - Generating Electricity in Coal-Fired Power Plants	ENG	PDF	412 KB
Application Report - Intelligent und Efficient: Temperature Measurement with Trip Amplifiers	ENG	PDF	285 KB
Application Report - Sand Trap and Preliminary Sedimentation Stage	ENG	PDF	448 KB
Application Report - Screening Systems in Sewage Treatment Plants	ENG	PDF	577 KB
Application Report - Sicherer Brennstofftransport in Kohlekraftwerken	ENG	PDF	391 KB
Application Report - Temperature Converter Detects Limit Values	ENG	PDF	348 KB
Application Report - Water Inlet in Wastewater Treatment Plants	ENG	PDF	526 KB

Product Documentation: KFD2-GUT-Ex1.D

Brief Instructions	Język	Typ pliku	Rozmiar pliku
Operator card KF-GUT-1.D / Bedienkarte KF-GUT-1.D	ALL	PDF	348 KB
Safety and Security Documentation
Instrukcja obsługi	POL	PDF	168 KB
Manuals
Manual	ENG	PDF	1342 KB
Manual	ENG	PDF	3685 KB
Installation and configuration guide Device Type Manager (DTM)	ENG	PDF	8665 KB

Design / Simulation: KFD2-GUT-Ex1.D

CAD	Język	Typ pliku	Rozmiar pliku
CAD 3-D / CAD 3-D	ALL	STP	2720 KB
CAD Portal / CAD Portal	ALL	LINK	---
CAE
CAE EPLAN Data Portal / CAE EPLAN Data Portal	ALL	LINK	---
EPLAN macro EDZ / EPLAN Makro EDZ	ALL	EDZ	83 KB

Approvals: KFD2-GUT-Ex1.D

Certificates	Nr. certyfikatu	Język	Typ pliku	Rozmiar pliku
China SITIIAS CCC Ex Certificate	2020322316001421 (Singapore)	ALL	PDF	1074 KB
DNV Marine	TAA00001WX	ALL	PDF	106 KB
Europe Pepperl+Fuchs Certificate of Compliance ATEX Category 3	PF 08 CERT 1213 X	ALL	PDF	198 KB
Europe TUV Nord ATEX Category (1) D ATEX Category (M1) ATEX Category (1) G	TÜV 03 ATEX 2140	ALL	PDF	371 KB
India PESO (India) CCOE	A/P/HQ/KA/104/5959 (P542586)	ALL	PDF	84 KB
Korea KOSHA	18-AV4BO-230	ALL	PDF	645 KB
South Africa MASC	MASC MS/17-0880	ALL	PDF	731 KB
TUV Nord IECEx Certificate of Conformity	IECEx TUN 09.0019	ALL	LINK	---
United Kingdom CML UK-Type Examination Certificate UKEX Category (1) D UKEX Category (1) G UKEX Category (M1)	CML 22UKEX2498X	ALL	PDF	164 KB
exida Functional Safety Assessment	P+F 05/03-24 R023	ALL	PDF	437 KB
Declaration of Conformity
EU Declaration of Conformity (P+F)	TDOC-0052EPOL	POL	PDF	184 KB

Software: KFD2-GUT-Ex1.D

Device Description Files/Drivers	Informacja o wersji	Typ pliku	Rozmiar pliku
DTM Collection Interface Technology 2 / DTM Collection Interface Technology 2	1.4.110.77	ZIP	---
Software Tools
PACTware 4.1 SP6 / PACTware 4.1 SP6	4.1.0.53	ZIP	43327 KB
PACTware 5.0 / PACTware 5.0	5.0.5.31	ZIP	44203 KB
PACTware 6.X / PACTware 6.X	6.1	ZIP	335938 KB

Produkty powiązane: KFD2-GUT-Ex1.D

Matching System Components

	KFD2-EB2 Power Feed Module
	Interface for Power Rail, Supply current ≤ 4 A, Replaceable fuse, Relay contact output, reversible, LED status indicationpa

	UPR-03 Universal Power Rail
	35 mm DIN mounting rail with 3-conductor insert, Provides DC supply voltage to all equipped K-System modules, Standard length 2 m (6 foot), simple to customize to application space, Eliminates daisy-chainspa

	UPR-03-S Universal Power Rail
	35 mm DIN mounting rail with 3-conductor insert, Provides DC supply voltage to all equipped K-System modules, Standard length 0.8 m (2.6 ft), simple to customize to application space, Eliminates daisy-chainspa

	DTM Interface Technology DTM collection
	Device DTM, For K-, E- and H-System, Frame application, like e. g. PACTware, must be installed separatelypa

	PACTware 5.0 FDT Framework
	Universal DTM host platform, For all DTMs of Pepperl+Fuchs, Approved FDT/DTM technology, Free of charge, Download from Pepperl+Fuchs websitepa

	K-ADP-USB Adapter with USB Interface
	Isolated USB interface cable, Used with K-, E- and H-System devices, Used with PACTwarepa

	UPR-03-M Universal Power Rail
	35 mm DIN mounting rail with 3-conductor insert, Provides DC supply voltage to all equipped K-System modules, Standard length 1.6 m (5 foot), simple to customize to application space, Eliminates daisy-chainspa

	K-DUCT-BU Profile Rail
	Cable trunking is integrated in the mounting profile, Safe spacious separation of safe and hazardous signals, No additional cable guides necessary, Standard length 1.8 m (5.8 ft), simple to customize to application space, With mounting aidspa

	K-DUCT-BU-UPR-03 Profile Rail
	Cable trunking with integrated Power Rail UPR-03, Safe spacious separation of safe and hazardous signals, No additional cable guides necessary, Provides DC supply voltage to all equipped K-System modules, Standard length 1.8 m (5.8 ft), simple to customize to application space, With end caps UPR-E, cover and mounting aidspa

	PACTware 6.x FDT Framework
	Universal DTM host platform, For all DTMs of Pepperl+Fuchs, Approved FDT/DTM technology, Free of charge, Download from Pepperl+Fuchs websitepa

Accessories

	K-CJC-BU Terminal Block for Cold Junction Compensation
	3-pin screw terminal, For KF modules of K-System, Integrated Cold Junction Compensation, Packaging unit: 1 piece, bluepa

	K-250R Measuring resistor
	1-channel, Precision resistor, Conversion of 0 mA ... 20 mA/0 V ... 5 Vpa

	K-500R0%1 Measuring resistor
	1-channel, Precision resistor, Conversion of 4 mA ... 20 mA/2 V ... 10 Vpa

	KF-ST-5GN Terminal Block
	3-pin screw terminal, For KF modules of K-System, Packaging unit: 5 pieces greenpa

	KF-ST-5BU Terminal Block
	3-pin screw terminal, For KF modules of K-System, Packaging unit: 5 pieces bluepa

	KF-CP Coding Pins
	Coding of K-System terminal blocks, Coding of LB/FB-System front sockets, Packaging unit: 20 x 6 coding pinspa

Uwagi ogólne dotyczące informacji o produktach firmy Pepperl+Fuchs

Linki

Selector for Safety Products

Choose from various selection criteria like safety integrity level, performance level, device function, and signal type and find the SIL/PL assessed device that you are looking for.

Pepperl+Fuchs Sp. z o.o.
ul. Owsiana 12
03-825 Warszawa
Polska
NIP: 522-28-27-777
phone +48 22 256 9770

Pepperl+Fuchs jest czołową firmą konstruującą i produkującą czujniki elektroniczne oraz inne komponenty dla globalnego rynku automatyki. Innowacyjność, wysoka jakość oraz stały rozwój firmy powodują, iż z sukcesem jesteśmy obecni na rynku od ponad 70 lat. Pepperl+Fuchs zatrudnia ponad 6300 pracowników na całym świecie i ma swoje zakłady produkcyjne w Niemczech, USA, Singapurze, na Węgrzech, w Indonezji i Wietnamie. Większość z nich posiada certyfikat ISO 9001.