Temperature Converter with Trip Values KFD2-GUT-1.D

1-channel signal conditioner
24 V DC supply (Power Rail)
Thermocouple, RTD, potentiometer or voltage input
Redundant TC input
Current output 0/4 mA ... 20 mA
2 relay contact outputs
Configurable by PACTware or keypad
Line fault (LFD) and sensor burnout detection
Up to SIL 2 acc. to IEC 61508

Technical Data
Product Documentation
Design / Simulation
Approvals
Software
Produkty powiązane

Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.

Pobierz pełną kartę katalogową w formie pliku PDF:

Dane techniczne KFD2-GUT-1.D

General specifications
Signal type		Analog input
Supply
Connection		terminals 23+, 24- or power feed module/Power Rail
Rated voltage		20 ... 30 V DC
Rated current		approx. 100 mA
Power dissipation/power consumption		≤ 2 W / 2.2 W
Input
Connection		terminals 1, 2, 3, 4, 6
RTD		Pt100, Pt500, Pt1000, Ni100, Ni1000
	Types of measuring	2-, 3-, 4-wire technology
	Lead resistance	max. 50 Ω
	Measurement loop monitoring	sensor breakage, sensor short-circuit
Thermocouples		type B, E, J, K, L, N, R, S, T (IEC 584-1: 1995)
	Cold junction compensation	external and internal
	Measurement loop monitoring	sensor breakage
Potentiometer		0.8 ... 20 kΩ
	Types of measuring	2-, 3-, 5-wire technology
Voltage		0 ... 10 V , 2 ... 10 V , 0 ... 1 V , -100 ... 100 mV
Input resistance		≥ 250 kΩ (0 ... 10 V) min. 1 MΩ (0 ... 1 V, -100 ... 100 mV)
Measuring current		approx. 400 µA with resistance measuring sensor
Output
Connection		output I: terminals 10, 11, 12 output II: terminals 16, 17, 18 output III: terminals 8+, 7-
Output I, II		relay
	Contact loading	250 V AC / 2 A / cos φ ≥ 0.7 ; 40 DC / 2 A
	Mechanical life	5 x 10⁷ switching cycles
	Energized/De-energized delay	approx. 20 ms / approx. 20 ms
Output III		Analog current output
	Current range	0 ... 20 mA or 4 ... 20 mA
	Open loop voltage	max. 24 V DC
	Load	max. 650 Ω
	Fault signal	downscale I ≤ 3.6 mA, upscale I ≥ 21 mA (acc. NAMUR NE43)
Transfer characteristics
Deviation
	Temperature effect	Input: 0.005 %/K (50 ppm) of span ; current output: 0.005 %/K (50 ppm) of span
	RTD	max. 0.2 % of span
	Thermocouples	max. 10µV deviation of CJC: ±0.8 K
	Voltage	0.1 % of span
	Potentiometer	0.1 % of span when < 5 kΩ 0.5 % of span when > 5 kΩ
	Current output	max. 20 µA
Sampling rate		approx. 700 ms
Galvanic isolation
Input/Other circuits		safe galvanic isolation acc. to EN 50020, voltage peak value 375 V
Output I, II against eachother		reinforced insulation according to IEC 61140, rated insulation voltage 300 V_eff
Output I, II/other circuits		reinforced insulation according to IEC 61140, rated insulation voltage 300 V_eff
Output III/power supply and collective error		reinforced insulation according to IEC 61140, rated insulation voltage 300 V_eff
Interface/power supply		reinforced insulation according to IEC 61140, rated insulation voltage 300 V_eff
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2013 (industrial locations)
Low voltage
	Directive 2014/35/EU	EN 61010-1:2010
Conformity
Insulation coordination		EN 50178
Galvanic isolation		EN 50178
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Mechanical specifications
Degree of protection		IP20
Mass		300 g
Dimensions		40 x 119 x 115 mm (1.6 x 4.7 x 4.5 inch) , housing type C2
	Height	119 mm
	Width	40 mm
	Length	115 mm
Mounting		on 35 mm DIN mounting rail acc. to EN 60715:2001
General information
Supplementary information		Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.

Classifications

System	Classcode
ECLASS 13.0	27210129
ECLASS 12.0	27210129
ECLASS 11.0	27210129
ECLASS 10.0.1	27210129
ECLASS 9.0	27210129
ECLASS 8.0	27210190
ECLASS 5.1	27210107
ETIM 9.0	EC002919
ETIM 8.0	EC002919
ETIM 7.0	EC002919
ETIM 6.0	EC002919
ETIM 5.0	EC001485
UNSPSC 12.1	32101514

Details: KFD2-GUT-1.D

Product Documentation: KFD2-GUT-1.D

Brief Instructions	Język	Typ pliku	Rozmiar pliku
Operator card KF-GUT-1.D / Bedienkarte KF-GUT-1.D	ALL	PDF	348 KB
Safety and Security Documentation
Instrukcja obsługi	POL	PDF	57 KB
Manuals
Manual	ENG	PDF	1342 KB
System Manual	ENG	PDF	3694 KB

Design / Simulation: KFD2-GUT-1.D

CAD	Język	Typ pliku	Rozmiar pliku
CAD 2-D / CAD 2-D	ALL	ZIP	657 KB
CAD 3-D / CAD 3-D	ALL	STP	870 KB
CAD Portal / CAD Portal	ALL	LINK	---
CAE
CAE EPLAN macro EDZ / CAE EPLAN Makro EDZ	ALL	EDZ	2450 KB

Approvals: KFD2-GUT-1.D

Certificates	Nr. certyfikatu	Język	Typ pliku	Rozmiar pliku
exida Functional Safety Assessment	P+F 05/03-24 R023	ALL	PDF	437 KB
Declaration of Conformity
EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F)	DOC-1887A	ALL	PDF	55 KB

Software: KFD2-GUT-1.D

Software Tools	Informacja o wersji	Typ pliku	Rozmiar pliku
PACTware 4.1 SP6 / PACTware 4.1 SP6	4.1.0.53	ZIP	43327 KB

Produkty powiązane: KFD2-GUT-1.D

Accessories

	PACTware 4.1 FDT Framework
	Universal DTM host platform, For all DTMs of Pepperl+Fuchs, Approved FDT/DTM technology, Free of charge, Internet download possiblepa

	DTM Interface Technology DTM collection
	Device DTM, For K-, E- and H-System, Frame application, like e. g. PACTware, must be installed separatelypa

Uwagi ogólne dotyczące informacji o produktach firmy Pepperl+Fuchs

Linki

Selector for Safety Products

Choose from various selection criteria like safety integrity level, performance level, device function, and signal type and find the SIL/PL assessed device that you are looking for.

Pepperl+Fuchs Sp. z o.o.
ul. Owsiana 12
03-825 Warszawa
Polska
NIP: 522-28-27-777
phone +48 22 256 9770

Pepperl+Fuchs jest czołową firmą konstruującą i produkującą czujniki elektroniczne oraz inne komponenty dla globalnego rynku automatyki. Innowacyjność, wysoka jakość oraz stały rozwój firmy powodują, iż z sukcesem jesteśmy obecni na rynku od ponad 70 lat. Pepperl+Fuchs zatrudnia ponad 6300 pracowników na całym świecie i ma swoje zakłady produkcyjne w Niemczech, USA, Singapurze, na Węgrzech, w Indonezji i Wietnamie. Większość z nich posiada certyfikat ISO 9001.