Frequency Converter with Direction and Synchronization Monitor KFD2-UFT-2.D

2-channel signal conditioner
24 V DC supply (Power Rail)
Dry contact or NAMUR inputs
Input frequency 1 mHz ... 1 kHz
Current output 0/4 mA ... 20 mA
Relay contact and transistor output
Start-up override
Configurable by PACTware or keypad
Line fault detection (LFD)

Technical Data
Details
Informative Literature
Product Documentation
Design / Simulation
Approvals
Software
Produkty powiązane

Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.

Pobierz pełną kartę katalogową w formie pliku PDF:

Dane techniczne KFD2-UFT-2.D

General specifications
Signal type		Digital Input
Supply
Connection		terminals 23+, 24- or power feed module/Power Rail
Rated voltage		20 ... 30 V DC
Rated current		approx. 130 mA
Power dissipation		2.2 W
Power consumption		2.5 W
Interface
Programming interface		programming socket
Input
Connection side		field side
Connection		input I: terminals 1+, 3- input II: terminals 4+, 6- input III: terminals 13+, 14- (control input 1) input IV: terminals 15+, 14- (control input 2)
Input I, II		2-wire sensor, sensor acc. to EN 60947-5-6 (NAMUR) or mechanical contact
	Open circuit voltage/short-circuit current	8.2 V / 10 mA
	Switching point/switching hysteresis	logic 1: > 2.5 mA ; logic 0: < 1.9 mA
	Pulse duration	min. 250 µs , overlap on direction of rotation signal: ≥ 125 µs
	Input frequency	rotation direction monitoring 0.001 ... 1000 Hz slip monitoring 10 ... 1000 Hz
	Line fault detection	breakage I ≤ 0.15 mA; short-circuit I > 4 mA
Input III, IV
	Active/Passive	I > 4 mA (for min. 100 ms) / I < 1.5 mA
	Open circuit voltage/short-circuit current	18 V / 5 mA
Output
Connection side		control side
Connection		output I: terminals 10, 11, 12 output II: terminals 16, 17, 18 output III: terminals 19+, 20- output IV: terminals 21+, 20- output V: terminals 7-, 8+
Output I, II		signal, relay
	Contact loading	250 V AC / 2 A / cos φ ≥ 0.7 ; 40 DC / 2 A
	Mechanical life	5 x 10⁷ switching cycles
	Energized/De-energized delay	approx. 20 ms / approx. 20 ms
Output III and IV		signal , electronic output, passive
	Contact loading	40 V DC
	Signal level	1-signal: (L+) -2.5 V (50 mA, short-circuit/overload proof) 0-signal: blocked output (off-state current ≤ 10 µA)
Output V		analog
	Current range	0 ... 20 mA or 4 ... 20 mA
	Open loop voltage	max. 24 V DC
	Load	max. 650 Ω
	Fault signal	downscale I ≤ 3.6 mA, upscale I ≥ 21.5 mA (acc. NAMUR NE43)
Collective error message		Power Rail
Transfer characteristics
Input I and II
	Measuring range	0.001 ... 1000 Hz
	Resolution	slip monitoring: 1% frequency measurement: 0,1% of measured value; but >0.001Hz
	Accuracy	slip monitoring: 1% frequency measurement: 0.5% of measured value; but >0.001Hz
	Measuring time	frequency measurement: < 100 ms
	Influence of ambient temperature	0.003 %/K (30 ppm)
Output I, II
	Response delay	≤ 200 ms
Output V
	Resolution	< 10 µA
	Accuracy	< 30 µA
	Influence of ambient temperature	0.005 %/K (50 ppm)
Galvanic isolation
Input I, II/other circuits		reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 V_eff
Input III, IV/power supply and collective error		functional insulation acc. to IEC 62103, rated insulation voltage 50 V_eff
Output I, II/other circuits		reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 V_eff
Mutual output I, II, III		reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 V_eff
Mutual output I, II, IV		reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 V_eff
Output III, IV/power supply and collective error		basic insulation according to IEC/EN 61010-1, rated insulation voltage 50 V_eff
Output III, IV/input III, IV		basic insulation according to IEC/EN 61010-1, rated insulation voltage 50 V_eff
Output III, IV/V		basic insulation according to IEC/EN 61010-1, rated insulation voltage 50 V_eff
Output V/power supply and collective error		functional insulation acc. to IEC 62103, rated insulation voltage 50 V_eff
Interface/power supply and collective error		functional insulation acc. to IEC 62103, rated insulation voltage 50 V_eff
Interface/output III, IV		basic insulation according to IEC/EN 61010-1, rated insulation voltage 50 V_eff
Indicators/settings
Display elements		LEDs , display
Control elements		Control panel
Configuration		via operating buttons via PACTware
Labeling		space for labeling at the front
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2013 (industrial locations)
Low voltage
	Directive 2014/35/EU	EN 61010-1:2010
Conformity
Electromagnetic compatibility		NE 21:2006
Degree of protection		IEC 60529:2001
Input		EN 60947-5-6:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Mechanical specifications
Degree of protection		IP20
Connection		screw terminals
Mass		300 g
Dimensions		40 x 119 x 115 mm (1.6 x 4.7 x 4.5 inch) (W x H x D) , housing type C2
	Height	119 mm
	Width	40 mm
	Depth	115 mm
Mounting		on 35 mm DIN mounting rail acc. to EN 60715:2001
International approvals
UL approval		E223772
General information
Supplementary information		Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.

Classifications

System	Classcode
ECLASS 13.0	27210128
ECLASS 12.0	27210128
ECLASS 11.0	27210128
ECLASS 10.0.1	27210128
ECLASS 9.0	27210128
ECLASS 8.0	27210190
ECLASS 5.1	27210121
ETIM 9.0	EC002918
ETIM 8.0	EC002918
ETIM 7.0	EC002918
ETIM 6.0	EC002918
ETIM 5.0	EC002475
UNSPSC 12.1	39121007

Details: KFD2-UFT-2.D

Function

This signal conditioner analyzes 2 digital signals (NAMUR sensor/mechanical contact) and functions as a rotation direction indicator, slip monitor, frequency monitor or synchronization monitor.

Each proximity sensor or switch controls a passive transistor output. The 2 relay outputs indicate if the input signal is above or below the trip value or the rotational direction.

The analog output can be programmed to be proportional to the input frequency or slip differential.

The unit is easily programmed by the use of a keypad located on the front of the unit or with the PACTware™ configuration software.

Line fault detection of the field current is indicated by a red LED and through the collective error output via Power Rail.

For additional information, refer to the manual and www.pepperl-fuchs.com.

Informative Literature: KFD2-UFT-2.D

Literature	Język	Typ pliku	Rozmiar pliku
Application Report - Biological Cleaning of Wastwater and Secondary Sedimentation Stage	ENG	PDF	566 KB
Application Report - Generating Electricity in Coal-Fired Power Plants	ENG	PDF	412 KB
Application Report - Sand Trap and Preliminary Sedimentation Stage	ENG	PDF	448 KB
Application Report - Screening Systems in Sewage Treatment Plants	ENG	PDF	577 KB

Product Documentation: KFD2-UFT-2.D

Brief Instructions	Język	Typ pliku	Rozmiar pliku
Operator card KF-UFT-2.D / Bedienkarte KF-UFT-2.D	ALL	PDF	831 KB
Safety and Security Documentation
Instrukcja obsługi	POL	PDF	57 KB
Manuals
Manual KF**-UFT-(Ex)2.D	ENG	PDF	1611 KB
System Manual	ENG	PDF	3694 KB
Installation and configuration guide Device Type Manager (DTM)	ENG	PDF	8665 KB

Design / Simulation: KFD2-UFT-2.D

CAD	Język	Typ pliku	Rozmiar pliku
CAD 3-D / CAD 3-D	ALL	STP	2722 KB
CAD Portal / CAD Portal	ALL	LINK	---
CAE
CAE EPLAN Data Portal / CAE EPLAN Data Portal	ALL	LINK	---
CAE EPLAN macro EDZ / CAE EPLAN Makro EDZ	ALL	EDZ	2740 KB

Approvals: KFD2-UFT-2.D

Certificates	Nr. certyfikatu	Język	Typ pliku	Rozmiar pliku
DNV Marine	TAA00001WX	ALL	PDF	106 KB
USA Canada UL cULus Hazardous Location UL E223772 UL	CoC 20200622 - E223772 RepRef 20071210	ALL	PDF	82 KB
Declaration of Conformity
EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F)	DOC-0256B	ALL	PDF	100 KB
UKCA-Declaration of conformity / UKCA-Konformitätserklärung	DOC-6697	ALL	PDF	93 KB

Software: KFD2-UFT-2.D

Device Description Files/Drivers	Informacja o wersji	Typ pliku	Rozmiar pliku
DTM Collection Interface Technology 2 / DTM Collection Interface Technology 2	1.4.110.77	ZIP	---
Software Tools
PACTware 4.1 SP6 / PACTware 4.1 SP6	4.1.0.53	ZIP	43327 KB
PACTware 5.0 / PACTware 5.0	5.0.5.31	ZIP	44203 KB
PACTware 6.X / PACTware 6.X	6.1	ZIP	335938 KB

Produkty powiązane: KFD2-UFT-2.D

Matching System Components

	KFD2-EB2 Power Feed Module
	Interface for Power Rail, Supply current ≤ 4 A, Replaceable fuse, Relay contact output, reversible, LED status indicationpa

	UPR-03 Universal Power Rail
	35 mm DIN mounting rail with 3-conductor insert, Provides DC supply voltage to all equipped K-System modules, Standard length 2 m (6 foot), simple to customize to application space, Eliminates daisy-chainspa

	UPR-03-S Universal Power Rail
	35 mm DIN mounting rail with 3-conductor insert, Provides DC supply voltage to all equipped K-System modules, Standard length 0.8 m (2.6 ft), simple to customize to application space, Eliminates daisy-chainspa

	DTM Interface Technology DTM collection
	Device DTM, For K-, E- and H-System, Frame application, like e. g. PACTware, must be installed separatelypa

	PACTware 5.0 FDT Framework
	Universal DTM host platform, For all DTMs of Pepperl+Fuchs, Approved FDT/DTM technology, Free of charge, Download from Pepperl+Fuchs websitepa

	K-ADP-USB Adapter with USB Interface
	Isolated USB interface cable, Used with K-, E- and H-System devices, Used with PACTwarepa

	UPR-03-M Universal Power Rail
	35 mm DIN mounting rail with 3-conductor insert, Provides DC supply voltage to all equipped K-System modules, Standard length 1.6 m (5 foot), simple to customize to application space, Eliminates daisy-chainspa

	K-DUCT-GY Profile Rail
	Cable trunking is integrated in the mounting profile, Safe spacious separation of field and control signals, No additional cable guides necessary, Standard length 1.8 m (5.8 ft), simple to customize to application space, With mounting aidspa

	K-DUCT-GY-UPR-03 Profile Rail
	Cable trunking with integrated Power Rail UPR-03, Safe spacious separation of field and control signals, No additional cable guides necessary, Provides DC supply voltage to all equipped K-System modules, Standard length 1.8 m (5.8 ft), simple to customize to application space, With end caps UPR-E, cover and mounting aidspa

	PACTware 6.x FDT Framework
	Universal DTM host platform, For all DTMs of Pepperl+Fuchs, Approved FDT/DTM technology, Free of charge, Download from Pepperl+Fuchs websitepa

Accessories

	K-250R Measuring resistor
	1-channel, Precision resistor, Conversion of 0 mA ... 20 mA/0 V ... 5 Vpa

	K-500R0%1 Measuring resistor
	1-channel, Precision resistor, Conversion of 4 mA ... 20 mA/2 V ... 10 Vpa

	KF-ST-5GN Terminal Block
	3-pin screw terminal, For KF modules of K-System, Packaging unit: 5 pieces greenpa

	KF-CP Coding Pins
	Coding of K-System terminal blocks, Coding of LB/FB-System front sockets, Packaging unit: 20 x 6 coding pinspa

Uwagi ogólne dotyczące informacji o produktach firmy Pepperl+Fuchs

Linki

Selector for Safety Products

Choose from various selection criteria like safety integrity level, performance level, device function, and signal type and find the SIL/PL assessed device that you are looking for.

Pepperl+Fuchs Sp. z o.o.
ul. Owsiana 12
03-825 Warszawa
Polska
NIP: 522-28-27-777
phone +48 22 256 9770

Pepperl+Fuchs jest czołową firmą konstruującą i produkującą czujniki elektroniczne oraz inne komponenty dla globalnego rynku automatyki. Innowacyjność, wysoka jakość oraz stały rozwój firmy powodują, iż z sukcesem jesteśmy obecni na rynku od ponad 70 lat. Pepperl+Fuchs zatrudnia ponad 6300 pracowników na całym świecie i ma swoje zakłady produkcyjne w Niemczech, USA, Singapurze, na Węgrzech, w Indonezji i Wietnamie. Większość z nich posiada certyfikat ISO 9001.