Wsparcie Czujników Przemysłowych
Wsparcie Ochrony przed wybuchem
Power Supply PS1000-A9-24.40
- 380 V AC to 480 V AC wide-range inputs
- Output 24 V DC, 40 A, 960 W, 3-phase
- Housing width 110 mm
- Efficiency up to 95.3 %
- Minimal inrush current surge
- Shutdown input
- Remote control for ON/OFF
- DC OK relay contact
- Current sharing for parallel use
Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.
Pobierz pełną kartę katalogową w formie pliku PDF:
Dane techniczne PS1000-A9-24.40
| Electrical specifications | ||
|---|---|---|
| Efficiency | 95.3 % at 3 x 400 V AC 95.2 % at 3 x 480 V AC |
|
| Power dissipation | 47.3 W at 3 x 400 V AC 48.4 W at 3 x 480 V AC |
|
| Input | ||
| Voltage range | 3x 380 ... 480 V AC (-15 %/+20 %), 50 ... 60 Hz (±6 %) | |
| Current | 1.65 A at 3 x 400 V AC 1.35 A at 3 x 480 V AC for lower output currents see technical information |
|
| Inrush current | 4.5 A peak at 3 x 400 V AC, temperature-independent 4.5 A peak at 3 x 480 V AC , temperature-independent |
|
| Capacity factor | 0.88 at 3 x 400 V AC 0.9 at 3 x 480 V AC |
|
| Remote control | terminals 15, 16 remote control for ON/OFF and shutdown input |
|
| Output | ||
| Rated voltage | 24 V DC | |
| Voltage range | 24 ... 28 V DC factory setting: 24.1 V |
|
| Rated current | 40 A | |
| Current | continuous: 40 ... 34.3 A short-term up to 4 s: 60 ... 51.5 A linear power derating see technical information |
|
| Power | 960 W | |
| Ripple | max. 100 mV pp | |
| Hold-up time | 25 ms at 3 x 400 V AC 25 ms at 3 x 480 V AC |
|
| Overload behavior | constant current mode | |
| Short-circuit current | typ. 46 A continuous, load impedance < 10 mΩ | |
| Voltage limitation | typ. 30.5 V DC max. 32 V DC |
|
| Fault indication output | ||
| Connection | terminals 13, 14 | |
| Output type | relay contact DC OK - contact is closed if the output voltage is > 90 % of the adjusted output voltage |
|
| Contact loading | max. 60 V DC/0.3 A ; 30 V DC/1 A ; 30 V AC/0.5 A resistive load min. 1 mA at 5 V DC |
|
| Galvanic isolation | ||
| Input/Output | SELV/PELV | |
| Indicators/settings | ||
| Display elements | LED green: status DC OK - LED lights up if the output voltage is > 90 % of the adjusted output voltage LED red: overload - LED lights up if the output voltage is < 90 % of the adjusted output voltage or in case of short circuit - flashes if the shutdown has been activated or if the device has shut down due to overtemperature |
|
| Control elements | potentiometer , plug-in jumper | |
| Configuration | setting of the output voltage via potentiometer setting of the operating mode - plug-in jumper plugged in: "parallel use" operating mode - plug-in jumper not plugged in: "single use" operating mode setting of the shutdown input: - plug-in jumper plugged in: device switches off |
|
| Directive conformity | ||
| Electromagnetic compatibility | ||
| Directive 2014/30/EU | IEC/EN 61000-6-1 , IEC/EN 61000-6-2 , IEC/EN 61000-6-3 , IEC/EN 61000-6-4 , IEC/EN 61000-3-2 , IEC/EN 61000-3-3 |
|
| Low voltage | ||
| Directive 2014/35/EU | EN 61010-1 | |
| RoHS | ||
| Directive 2011/65/EU (RoHS) | IEC/EN 63000:2019 | |
| Conformity | ||
| Degree of protection | EN 60529 | |
| Shock resistance | EN 60068-2-27 | |
| Vibration resistance | EN 60068-2-6 | |
| Ambient conditions | ||
| Ambient temperature | -25 ... 70 °C (-13 ... 158 °F) , see technical information | |
| Storage temperature | -40 ... 85 °C (-40 ... 185 °F) | |
| Relative humidity | 5 ... 95 %, noncondensing | |
| Shock resistance | 15 g , 6 ms or 10 g , 11 ms | |
| Vibration resistance | 2 ... 17.8 Hz : ± 1.6 mm , 17.8 ... 500 Hz : 1 g | |
| Mechanical specifications | ||
| Housing material | aluminum alloy , galvanized steel | |
| Degree of protection | IP20 | |
| Connection | ||
| Input | screw terminals conductor cross section: max. 6 mm2 (AWG 20-10) cable diameter: max. 2.8 mm, wire end ferrules included stripped insulation length: 7 mm tightening torque: max. 1 Nm |
|
| Output | screw terminals conductor cross section: max. 16 mm2 (AWG 22-8) cable diameter: max. 5.2 mm, wire end ferrules included stripped insulation length: 12 mm tightening torque: max. 2.3 Nm |
|
| Relay contact output | spring terminals conductor cross section: max. 1.5 mm2 (AWG 24-16) cable diameter: max. 1.6 mm, wire end ferrules included stripped insulation length: 7 mm |
|
| Remote control/shutdown input | spring terminals conductor cross section: max. 1.5 mm2 (AWG 24-16) cable diameter: max. 1.6 mm, wire end ferrules included stripped insulation length: 7 mm |
|
| Mass | approx. 1500 g | |
| Dimensions | 110 x 124 x 127 mm (W x H x D) , without DIN mounting rail | |
| Height | 124 mm | |
| Width | 110 mm | |
| Depth | 127 mm | |
| Mounting | on 35 mm DIN mounting rail acc. to EN 60715:2001 | |
| International approvals | ||
| UL approval | E223176 | |
| General information | ||
| Supplementary information | Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com. | |
Classifications
| System | Classcode |
|---|---|
| ECLASS 13.0 | 27040790 |
| ECLASS 12.0 | 27040790 |
| ECLASS 11.0 | 27040790 |
| ECLASS 10.0.1 | 27040790 |
| ECLASS 9.0 | 27040790 |
| ECLASS 8.0 | 27049090 |
| ECLASS 5.1 | 27049090 |
| ETIM 9.0 | EC002542 |
| ETIM 8.0 | EC002542 |
| ETIM 7.0 | EC002542 |
| ETIM 6.0 | EC002542 |
| ETIM 5.0 | EC002542 |
| UNSPSC 12.1 | 39121004 |
Details: PS1000-A9-24.40
Function
The device is used to supply field devices with 24 V DC and 40 A.
The device has a large power reserve of 150 % for up to 4 s to support the starting of heavy loads such as DC motors or capacitive loads.
The output voltage can be adjusted via a potentiometer. Device status and overload are indicated by LEDs.
The device has a relay contact output for remote monitoring.
The device has a connection for switching off the device via a switch or an external voltage.
The device is mounted on a 35 mm DIN mounting rail according to EN 60715.
Informative Literature: PS1000-A9-24.40
| Literature | Język | Typ pliku | Rozmiar pliku |
|---|---|---|---|
| Product Information - PS1000 for Global Use up to Zone 2/Div. 2 | ENG | 577 KB |
Product Documentation: PS1000-A9-24.40
| Product information | Język | Typ pliku | Rozmiar pliku |
|---|---|---|---|
| Technical information | ENG | 2915 KB | |
| Safety and Security Documentation | |||
| Instruction manual / Betriebsanleitung | ALL | 307 KB | |
Design / Simulation: PS1000-A9-24.40
| CAD | Język | Typ pliku | Rozmiar pliku |
|---|---|---|---|
| CAD 3-D / CAD 3-D | ALL | STP | 10238 KB |
| CAD Portal / CAD Portal | ALL | LINK | --- |
| CAE | |||
| CAE EPLAN macro EDZ / CAE EPLAN Makro EDZ | ALL | EDZ | 211 KB |
Approvals: PS1000-A9-24.40
| Certificates | Nr. certyfikatu | Język | Typ pliku | Rozmiar pliku |
|---|---|---|---|---|
| DNV GL Marine | TAA0000316 | ALL | 179 KB | |
| US CA UL | CoC E223176 RptRef E223176-20070416 | ALL | 444 KB | |
| Declaration of Conformity | ||||
| EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F) | DOC-4791 | ALL | 79 KB | |
| EU Declaration of Conformity (P+F) | TDOC-4791APOL | POL | 176 KB | |
Pepperl+Fuchs Sp. z o.o.
ul. Owsiana 12
03-825 Warszawa
Polska
NIP: 522-28-27-777
+48 22 256 9770
© 2024 Wszelkie prawa zastrzeżone
Pepperl+Fuchs jest czołową firmą konstruującą i produkującą czujniki elektroniczne oraz inne komponenty dla globalnego rynku automatyki. Innowacyjność, wysoka jakość oraz stały rozwój firmy powodują, iż z sukcesem jesteśmy obecni na rynku od ponad 70 lat. Pepperl+Fuchs zatrudnia ponad 6300 pracowników na całym świecie i ma swoje zakłady produkcyjne w Niemczech, USA, Singapurze, na Węgrzech, w Indonezji i Wietnamie. Większość z nich posiada certyfikat ISO 9001.