SMART Transmitter Power Supply/SMART Current Driver HiC2422

2-channel isolated barrier
24 V DC supply (bus powered)
Analog input (AI), Analog output (AO)
Operates as transmitter power supply or current driver
Up to SIL 2 (SC 3) acc. to IEC/EN 61508

Folha de Dados
Product Documentation
Design / Simulation
Approvals

Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.

Faça o download das folhas de dados em PDF:

Folhas de dados: Dados técnicos do HiC2422

General specifications
Signal type		Analog input/analog output
Functional safety related parameters
Safety Integrity Level (SIL)		SIL 2
Systematic capability (SC)		SC 3
Supply
Connection		SL1: 1a(-), 1b(-); 2a(+), 2b(+)
Rated voltage		19 ... 30 V DC via Termination Board
Ripple		max. 10 %
Rated current		max. 88 mA at 24 V
Power dissipation		max. 1.4 W
Power consumption		max. 2.1 W
Analog input
Number of channels		2
Suitable field devices		2-wire SMART transmitters
Signal		0/4 ... 20 mA , limited to approx. 30 mA
Field circuit		SL2: 5a(+), 5b(-); 1a(+), 1b(-)
Available voltage		min. 15 V at 20 mA min. 18 V at 4 mA
Control circuit		SL1: 8a(+), 7a(-); 10a(+), 9a(-)
Input voltage		Voltage across terminals 10 ... 30 V. If the current is supplied from a source > 24 V, series resistance of ≥ (V - 24)/0.02 Ω is needed, where V is the source voltage. The maximum value of the resistance is (V - 10)/0.02 Ω. (sink output)
Load		max. 350 Ω (source output)
Ripple		20 mV _eff
Analog output
Number of channels		2
Suitable field devices		SMART I/P converters (positioner), on-site-displays
Signal		0/4 ... 20 mA , limited to approx. 30 mA
Field circuit		SL2: 5a(+), 5b(-); 1a(+), 1b(-)
Load		max. 650 Ω
Voltage		min. 13 V at 20 mA
Ripple		20 mV _eff , on all signal terminals
Control circuit		SL1: 8a(+), 7a(-); 10a(+), 9a(-)
Voltage drop		max. 6 V
Line fault detection		> 100 kΩ at max. 30 V, with field wiring open
Transfer characteristics
Deviation		max. 20 µA incl. calibration, linearity, hysteresis, loads and fluctuations of supply voltage
	Influence of ambient temperature	< 2 µA/K (-40 ... 70 °C (-40 ... 158 °F))
Frequency range		field side into the control side: bandwidth with 0.5 V_pp signal 0 ... 3 kHz (-3 dB) control side into the field side: bandwidth with 0.5 V_pp signal 0 ... 3 kHz (-3 dB)
Settling time		max. 200 ms
Rise time/fall time		max. 100 ms (10 ... 90 %)
Galvanic isolation
Field circuit/control circuit		basic insulation according to IEC/EN 61010-1, rated insulation voltage 300 V_eff
Control circuit/control circuit		channel I/channel II : functional isolation, rated voltage: 50 V
Field circuit/power supply		reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 V_eff
Control circuit/power supply		basic insulation according to IEC/EN 61010-1, rated insulation voltage 60 V_eff
Indicators/settings
Display elements		LED
Factory setting		analog input with source output
Configuration		via DIP switches
Labeling		space for labeling at the front
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2013 (industrial locations)
Conformity
Electromagnetic compatibility		NE 21:2017 EN 61326-3-2:2018 For further information see system description.
Degree of protection		IEC 60529:2001
Protection against electrical shock		UL 61010-1:2012
Functional safety		IEC 61508:2010
Ambient conditions
Ambient temperature		-40 ... 70 °C (-40 ... 158 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Relative humidity		95 % non-condensing
Mechanical specifications
Degree of protection		IP20
Mass		approx. 100 g
Dimensions		12.5 x 106 x 128 mm (0.5 x 4.2 x 5.1 inch) (W x H x D)
	Height	106 mm
	Width	12.5 mm
	Depth	128 mm
Mounting		on termination board
Coding		pin 1 and 3 trimmed For further information see system description.
Data for application in connection with hazardous areas
EU-type examination certificate		UL 23 ATEX 3091 X
	Marking	II (1)G [Ex ia Ga] IIC II (1)D [Ex ia Da] IIIC I (M1) [Ex ia Ma] I
	Output	Ex ia, Ex iaD
	Voltage	25.2 V
	Current	100 mA
	Power	630 mW
	Internal capacitance	1.05 nF
	Internal inductance	0
Supply
	Maximum safe voltage	250 V _rms (Attention! The rated voltage can be lower.)
Input
	Maximum safe voltage	250 V _rms (Attention! The rated voltage can be lower.)
Certificate		UL 23 ATEX 3092 X
	Marking	II 3G Ex ec IIC T4 Gc
Galvanic isolation
	Field circuit/power supply	safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN IEC 60079-0:2018 , EN 60079-11:2012 , EN IEC 60079-7:2015+A1:2018
International approvals
UL approval		E106378
	Control drawing	116-0500 (cULus)
IECEx approval
	IECEx certificate	IECEx ULD 23.0026X
	IECEx marking	[Ex ia Ga] IIC , [Ex ia Da] IIIC , [Ex ia Ma] I Ex ec IIC T4 Gc
General information
Supplementary information		Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.

Classifications

System	Classcode
ECLASS 13.0	27210119
ECLASS 12.0	27210119
ECLASS 11.0	27210119
ECLASS 10.0.1	27210119
ECLASS 9.0	27210119
ECLASS 8.0	27210119
ECLASS 5.1	27210119
ETIM 9.0	EC001485
ETIM 8.0	EC001485
ETIM 7.0	EC001485
ETIM 6.0	EC001485
ETIM 5.0	EC001485
UNSPSC 12.1	32101514

Details: HiC2422

Product Documentation: HiC2422

Safety and Security Documentation	Idioma	Tipo de Arquivo	Tamanho do Arquivo
Manual de instruções	POR	PDF	166 KB
Functional Safety Manual	ENG	PDF	1982 KB
Manuals
System Manual	ENG	PDF	5438 KB

Design / Simulation: HiC2422

CAD	Idioma	Tipo de Arquivo	Tamanho do Arquivo
CAD 3-D / CAD 3-D	ALL	STP	2770 KB

Approvals: HiC2422

Certificates	Número do Certificado	Idioma	Tipo de Arquivo	Tamanho do Arquivo
Canada UL cUL Hazardous Location UL E106378	CoC UL-CA-2339915-1 Rep Ref E106378-20240424	ALL	PDF	217 KB
Canada UL cUL Hazardous Location UL E106378	CoC UL-CA-2339916-1 Rep Ref E106378-20240424	ALL	PDF	217 KB
Europe UL ATEX Category (1) D ATEX Category (M1) ATEX Category (1) G	UL 23 ATEX 3091X	ALL	PDF	568 KB
Europe United Kingdom UL ATEX Category 3 G	UL 23 ATEX 3092X	ALL	PDF	424 KB
USA UL UL E106378 Hazardous Location UL	CoC UL-US-2346170-1 Rep Ref E106378-20240424	ALL	PDF	255 KB
USA UL UL E106378 Hazardous Location UL	CoC UL-US-2346171-1 Rep Ref E106378-20240424	ALL	PDF	217 KB
Worldwide UL IECEx Certificate of Conformity	IECEx ULD 23.0026X	ALL	LINK	---
Control Drawings
Control drawing UL / Control drawing UL		ALL	PDF	87 KB
Declaration of Conformity
EU Declaration of Conformity (P+F)	TDOC-7580_POR	POR	PDF	226 KB

Notas Gerais sobre as informações de produto da Pepperl+Fuchs

Acesso Rápido

Selector for Safety Products

Choose from various selection criteria like safety integrity level, performance level, device function, and signal type and find the SIL/PL assessed device that you are looking for.

Pepperl+Fuchs Ltda.
Rua José Versolato, 111
Domo Corporate Tower, Conjunto 144
09750-730 São Bernardo do Campo, SP
Brasil
vendas@br.pepperl-fuchs.com
phone +55 11 4007 1448

A Pepperl+Fuchs é líder na fabricação e no desenvolvimento de sensores e componentes eletrônicos para o setor global da automação industrial. Inovação contínua, qualidade e crescimento constante garantem o nosso sucesso há mais de 70 anos. Empregamos mais de 6.300 colaboradores em todo o mundo e contamos com fábricas próprias na Alemanha, Estados Unidos, Cingapura, Hungria, Indonésia e Vietnã, todas com certificação ISO 9001.