Atendimento ao Cliente da Divisão de Sensores Industriais
Rede de Atendimento - Divisão de Proteção Contra Explosão
Ultrasonic sensor UC800-F77S-IU-IO-V31-P001
- IO-Link interface for parameterization
- Programmable via DTM with PACTWARE
- Selectable sound lobe width
- Synchronization options
- Temperature compensation
- Analog output
- Customer-specific configuration
Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.
Faça o download das folhas de dados em PDF:
Folhas de dados: Dados técnicos do UC800-F77S-IU-IO-V31-P001
| Descrição do Produto |
|---|
| Single head system |
| General specifications | ||
|---|---|---|
| Sensing range | 100 ... 800 mm | |
| Adjustment range | 100 ... 800 mm | |
| Dead band | 0 ... 100 mm | |
| Standard target plate | 100 mm x 100 mm | |
| Transducer frequency | approx. 255 kHz | |
| Response delay | minimum : 13 ms factory setting: 49 ms |
|
| Sensor cycle time | ≥ 13 ms (factory setting) ; programmable to 60 s |
|
| Memory | ||
| Non-volatile memory | EEPROM | |
| Write cycles | 300000 | |
| Indicators/operating means | ||
| LED green | solid: power on flashing: standby mode or IO-Link communication |
|
| LED yellow | solid: object in evaluation range flashing: programming of the limits, object detected |
|
| LED red | solid: fault flashing: programming limits, object not detected |
|
| Electrical specifications | ||
| Operating voltage | 18 ... 30 V DC , ripple 10 %SS |
|
| No-load supply current | ≤ 50 mA | |
| Power consumption | ≤ 500 mW | |
| Time delay before availability | ≤ 300 ms | |
| Interface | ||
| Interface type | IO-Link (available after activation via programming button until next reset) | |
| Input/Output | ||
| Input/output type | 1 synchronization connection, bidirectional | |
| 0 Level | 0 ... 1 V | |
| 1 Level | 2.5 V ... UB | |
| Input impedance | > 22 kΩ | |
| Output current | current source < 2.5 mA | |
| Pulse length | ≥ 1 ms with external control, low active | |
| Synchronization frequency | ||
| Common mode operation | ≤ 82 Hz | |
| Multiplex operation | ≤ 82 Hz / n , n = number of sensors , n ≤ 10 |
|
| Output | ||
| Output type | 1 analog output 0 (4) ... 20 mA or 1 analog output 0 ... 10 V |
|
| Resolution | current output: evaluation range [mm]/3200 but ≥ 0.35 mm voltage output: evaluation range [mm]/4000 but ≥ 0.35 mm |
|
| Deviation of the characteristic curve | ≤ ± 1 % of full-scale value | |
| Repeat accuracy | ≤ ± 0.1 % of full-scale value | |
| Load impedance | current output: ≤ 500 Ohm voltage output: ≥ 1000 Ohm |
|
| Temperature influence | ≤ ± 0.75 % of the end value (with temperature compensation) from 10 minutes after switching on the sensor ; 0.17 %/K (without temperature compensation) | |
| Compliance with standards and directives | ||
| Standard conformity | ||
| Standards | EN IEC 60947-5-2:2020 IEC 60947-5-2:2019 EN 60947-5-7:2003 IEC 60947-5-7:2003 IEC 61131-9:2013 |
|
| Approvals and certificates | ||
| UL approval | cULus Listed, Class 2 Power Source | |
| CCC approval | CCC approval / marking not required for products rated ≤36 V | |
| Ambient conditions | ||
| Ambient temperature | current output -25 ... 60 °C (-13 ... 140 °F) voltage output -25 ... 70 °C (-13 ... 158 °F) When fixing with one M18 nut, the temperature range for each begins with 0 °C (32 °F). |
|
| Storage temperature | -40 ... 85 °C (-40 ... 185 °F) | |
| Mechanical specifications | ||
| Connection type | Connector plug M8 x 1 , 4-pin | |
| Degree of protection | IP67 | |
| Material | ||
| Housing | Polycarbonate | |
| Transducer | epoxy resin/hollow glass sphere mixture; polyurethane foam | |
| Installation position | any position | |
| Mass | 13 g | |
| Tightening torque, fastening screws | with M3 nuts max. 0.2 Nm with M18 nuts max. 1 Nm |
|
| Dimensions | ||
| Height | 31 mm | |
| Width | 21 mm | |
| Length | 23 mm | |
| Factory settings | ||
| Output | near limit: 100 mm far limit: 800 mm Output mode: rising ramp output type: 4 ... 20 mA |
|
| Beam width | wide | |
Classifications
| System | Classcode |
|---|---|
| ECLASS 13.0 | 27272803 |
| ECLASS 12.0 | 27272803 |
| ECLASS 11.0 | 27272803 |
| ECLASS 10.0.1 | 27272803 |
| ECLASS 9.0 | 27272803 |
| ECLASS 8.0 | 27272803 |
| ECLASS 5.1 | 27272803 |
| ETIM 9.0 | EC001849 |
| ETIM 8.0 | EC001849 |
| ETIM 7.0 | EC001849 |
| ETIM 6.0 | EC001849 |
| ETIM 5.0 | EC001849 |
| UNSPSC 12.1 | 41111960 |
Details: UC800-F77S-IU-IO-V31-P001
Product Documentation: UC800-F77S-IU-IO-V31-P001
| Brief Instructions | Idioma | Tipo de Arquivo | Tamanho do Arquivo |
|---|---|---|---|
| Commissioning instruction for UC*-F77*-IU* / Inbetriebnahmeanleitung für UC*-F77*-IU* | ALL | 440 KB | |
| Manuals | |||
| Manual UC***-F77 Series Parameterization of Ultrasonic Sensors with IO-Link Interface | ENG | 4224 KB | |
Design / Simulation: UC800-F77S-IU-IO-V31-P001
| CAD | Idioma | Tipo de Arquivo | Tamanho do Arquivo |
|---|---|---|---|
| CAD 3-D / CAD 3-D | ALL | STP | 1739 KB |
| CAE | |||
| EPLAN macro EDZ / EPLAN Makro EDZ | ALL | EDZ | 63 KB |
Software: UC800-F77S-IU-IO-V31-P001
| Software Tools | Informações | Tipo de Arquivo | Tamanho do Arquivo |
|---|---|---|---|
| PACTware 4.1 SP6 / PACTware 4.1 SP6 | 4.1.0.53 | ZIP | 43327 KB |
| PACTware 5.0 / PACTware 5.0 | 5.0.5.31 | ZIP | 44203 KB |
| Pepperl+Fuchs PACTware Connection Wizard (Add-In for parameterization software PACTware) / Pepperl+Fuchs PACTware Connection Wizard (Add-In für Parametriersoftware PACTware) | 1.0.0.3 | ZIP | 295 KB |
Produtos Relacionados: UC800-F77S-IU-IO-V31-P001
| Accessories | ||||||
|---|---|---|---|---|---|---|
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
O Sistema de sensor ultrassônico de segurança USi está abrindo novos caminhos para aplicações de segurança, seja em ambientes empoeirados e desafiadores ou em áreas externas.
A Pepperl+Fuchs oferece a você vários documentos para download sobre os sensores ultrassônicos.
Pepperl+Fuchs Ltda.
Rua José Versolato, 111
Domo Corporate Tower, Conjunto 144
09750-730 São Bernardo do Campo, SP
Brasil
vendas@br.pepperl-fuchs.com
+55 11 4007 1448
© 2024 Todos os Direitos Reservados.
A Pepperl+Fuchs é líder na fabricação e no desenvolvimento de sensores e componentes eletrônicos para o setor global da automação industrial. Inovação contínua, qualidade e crescimento constante garantem o nosso sucesso há mais de 70 anos. Empregamos mais de 6.300 colaboradores em todo o mundo e contamos com fábricas próprias na Alemanha, Estados Unidos, Cingapura, Hungria, Indonésia e Vietnã, todas com certificação ISO 9001.