Servisní linka pro průmyslové snímače
Kontaktujte zákaznický servis
Servisní linka ochrany před výbuchem
Kontaktujte zákaznický servis
Nedostupné pro prodej
Nedostupné pro prodej

Ultrasonic sensor UCC2500-50GK-B26-8MOL

UCC2500-50GK-B26-8MOL
  • Thread M50
  • PTFE coated transducer
  • Power save mode
  • PWM output
  • Physical LIN interface
  • Serial Interfaces
  • Temperature compensation

Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.

Stáhněte si kompletní katalogový list ve formátu PDF:

English

Výňatek z katalogového listu: Technická data   UCC2500-50GK-B26-8MOL

Popis produktu
Single head system
General specifications
Sensing range150 ... 2500 mm
Dead band0 ... 150 mm
Standard target plate100 mm x 100 mm
Transducer frequencyapprox. 120 kHz
Electrical specifications
Operating voltagefor UART and PWM operation:
UUART/PWM = 2.5 ... 5 V DC, typical 3.3 V
for LIN operation:
ULIN = 8 ... 18 V DC, typical 12 V
No-load supply current≤ 60 mA at 3.3 V DC
≤ 20 mA at 12 V DC
Quiescent current indication< 3 µA during standby mode at UART- and PWM operation
Power consumption≤ 250 mW in the measurement operating mode
Time delay before availability≤ 70 ms
Interface 1
Interface typePhysical LIN interface
Transfer rate19.2 kBit/s (8N1)
Cycle time55 ms
Resolution10 mm (corresponding to 1 LSB)
Interface 2
Interface typeUART 3.3V
Transfer rate19.2 kBit/s (8N1)
Cycle time55 ms
Resolution10 mm (corresponding to 1 LSB)
Input
Input typeStandby active
Signal levellow: 0 ... 0.8 V
Output
Output typePWM output (PNP) , not short-circuit protected
Resolutionpulse length 10 µs /cm
Output currentmax. 10 mA
Temperature influence3 % of full-scale value over the entire temperature range
Directive conformity
Electromagnetic compatibility
Directive 2014/30/EUEN IEC 60947-5-2:2020 : chapter 8.2.6.2.2, 8.2.6.2.3, 8.2.6.3
The sensor is designed to be supplied by a battery. The sensor signals are further processed in a control unit, which is also responsible for EMC protection.
Ambient conditions
Ambient temperature-25 ... 70 °C (-13 ... 158 °F)
Storage temperature-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection typefixed cable with plug
Degree of protectionIP66 / IP67 ( connector excluded )
Material
HousingPBT
Transducerepoxy resin/hollow glass bead mixture; Polyurethane foam, PTFE coated
ConnectorMolex connector 70107-0007
Number of pins8
Cable
Length276 mm ± 20 mm
Mass100 g
Dimensions
Height37 mm
Width50 mm
Length50 mm
Factory settings
OutputPWM output (PNP)
Temperature compensation
Address setting 7
Beam widthwide
General information
Scope of delivery2 nuts plastic

Classifications

SystemClasscode
ECLASS 13.027272803
ECLASS 12.027272803
ECLASS 11.027272803
ECLASS 10.0.127272803
ECLASS 9.027272803
ECLASS 8.027272803
ECLASS 5.127272803
ETIM 9.0EC001849
ETIM 8.0EC001849
ETIM 7.0EC001849
ETIM 6.0EC001849
ETIM 5.0EC001849
UNSPSC 12.141111960
Systém senzorů USi-safety

Systém ultrazvukových senzorů USi-safety posouvá bezpečnostní aplikace na novou úroveň – ať již se jedná o aplikace v náročných, prašných prostředích nebo ve venkovních prostorách.

Společnost Pepperl+Fuchs vám nabízí různé dokumenty ke stažení, které obsahují poznatky o ultrazvukových senzorech.

undefined

We value your privacy!

We and our partners are using technologies like cookies and process personal data like the IP-address or browser information in order to personalize the advertising that you see. This helps us to show you more relevant ads and improves your internet experience. We also use it in order to measure results or align our website content. Because we value your privacy, we are herewith asking for your permission to use these technologies. You can always change/withdraw your consent later by clicking on the settings button on the left lower corner of the page.

Deny all cookies

We value your privacy!

Please select the group of cookies and scripts, that you consent to.

Functional
These cookies are necessary so that you can navigate through the pages and use essential functions (e.g. login).
Analytics
We use these cookies and scripts to measure the visits and clicks on our website in order to constantly improve it.
Marketing
These cookies and similar technologies are used to provide you with personalized and therefore relevant advertising content.