Frequency Converter with Trip Values KFD2-UFC-1.D

1-channel signal conditioner
24 V DC supply (Power Rail)
Input for 2- or 3-wire sensors, NAMUR sensors or dry contacts
Input frequency 1 mHz ... 10 kHz
Current output 0/4 mA ... 20 mA
Relay contact and transistor output
Start-up override
Line fault detection (LFD)
Up to SIL 2 acc. to IEC/EN 61508 / IEC/EN 61511

Technical Data
Informative Literature
Product Documentation
Design / Simulation
Approvals
Software
関連製品
お問い合わせ

注: Pepperl+Fuchs GmbH(旧社名)で発行された証明書・適合宣言書などすべての製品関連文書は、Pepperl+Fuchs AG(新社名)にそのまま適用されます。

データシート(PDF):

技術データ KFD2-UFC-1.D

General specifications
Signal type		Digital Input
Functional safety related parameters
Safety Integrity Level (SIL)		SIL 2
Supply
Connection		terminals 23+, 24- or power feed module/Power Rail
Rated voltage		20 ... 30 V DC
Rated current		approx. 100 mA
Power dissipation/power consumption		≤ 2 W / 2.2 W
Interface
Programming interface		programming socket
Input
Connection side		field side
Connection		Input I: 2-wire sensor: terminals 1+, 3- three wire sensor: terminals 1+, 2- and 3 input II: terminals 13+, 14- start-up override;
Input I		2- or 3-wire sensor, sensor acc. to EN 60947-5-6 (NAMUR) or mechanical contact
	Open circuit voltage/short-circuit current	22 V / 40 mA
	Input resistance	4.7 kΩ
	Switching point/switching hysteresis	logic 1: > 2.5 mA ; logic 0: < 1.9 mA
	Pulse duration	> 50 µs
	Input frequency	0.001 ... 10000 Hz
	Line fault detection	breakage I ≤ 0.15 mA; short-circuit I > 4 mA
Input II		startup override: 1 ... 1000 s, adjustable in steps of 1 s
	Active/Passive	I > 4 mA (for min. 100 ms) / I < 1.5 mA
	Open circuit voltage/short-circuit current	18 V / 5 mA
Output
Connection side		control side
Connection		output I: terminals 10, 11, 12 output II: terminals 16, 17, 18 outout III: terminasl 19+, 20- output IV: terminals 8+, 7-
Output I, II		signal, relay
	Contact loading	250 V AC / 2 A / cos φ ≥ 0.7 ; 40 V DC / 2 A
	Mechanical life	5 x 10⁷ switching cycles
	Energized/De-energized delay	approx. 20 ms / approx. 20 ms
Output III		electronic output, passive
	Contact loading	40 V DC
	Signal level	1-signal: (L+) -2.5 V (50 mA, short-circuit/overload proof) 0-signal: blocked output (off-state current ≤ 10 µA)
Output IV		analog
	Current range	0 ... 20 mA or 4 ... 20 mA
	Open loop voltage	max. 24 V DC
	Load	max. 650 Ω
	Fault signal	downscale I ≤ 3.6 mA , upscale ≥ 21.5 mA (acc. NAMUR NE43)
Collective error message		Power Rail
Transfer characteristics
Input I
	Measuring range	0.001 ... 10000 Hz
	Resolution	0.1 % of the measurement value , ≥ 0.001 Hz
	Accuracy	0.1 % of the measurement value , > 0.001 Hz
	Measuring time	< 100 ms
	Influence of ambient temperature	0.003 %/K (30 ppm)
Output I, II
	Response delay	≤ 200 ms
Output IV
	Resolution	< 10 µA
	Accuracy	< 20 µA
	Influence of ambient temperature	0.005 %/K (50 ppm)
Galvanic isolation
Input I/other circuits		reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 V_eff
Output I, II/other circuits		reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 V_eff
Mutual output I, II, III		reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 V_eff
Output III/power supply and collective error		basic insulation according to IEC/EN 61010-1, rated insulation voltage 50 V_eff
Output III/IV		basic insulation according to IEC/EN 61010-1, rated insulation voltage 50 V_eff
Output IV/power supply and collective error		functional insulation acc. to IEC 62103, rated insulation voltage 50 V_eff
Start-up override/power supply and collective error		functional insulation acc. to IEC 62103, rated insulation voltage 50 V_eff
Interface/power supply and collective error		functional insulation acc. to IEC 62103, rated insulation voltage 50 V_eff
Interface/output III		basic insulation according to IEC/EN 61010-1, rated insulation voltage 50 V_eff
Indicators/settings
Display elements		LEDs , display
Control elements		Control panel
Configuration		via operating buttons via PACTware
Labeling		space for labeling at the front
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2013 (industrial locations)
Low voltage
	Directive 2014/35/EU	EN 61010-1:2010
Conformity
Electromagnetic compatibility		NE 21:2006
Degree of protection		IEC 60529:2001
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Mechanical specifications
Degree of protection		IP20
Connection		screw terminals
Mass		300 g
Dimensions		40 x 119 x 115 mm (1.6 x 4.7 x 4.5 inch) (W x H x D) , housing type C2
	Height	119 mm
	Width	40 mm
	Depth	115 mm
Mounting		on 35 mm DIN mounting rail acc. to EN 60715:2001
Data for application in connection with hazardous areas
Certificate		PF 08 CERT 1216 X
	Marking	II 3G Ex nA nC IIC T4 Gc
Output I, II
	Contact loading	50 V AC/2 A/cos φ > 0.7; 40 V DC/1 A resistive load
Ambient conditions
	Ambient temperature	-20 ... 50 °C (-4 ... 122 °F)
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2012+A11:2013 , EN 60079-15:2010
International approvals
UL approval		E223772
General information
Supplementary information		Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.

Classifications

System	Classcode
ECLASS 13.0	27210128
ECLASS 12.0	27210128
ECLASS 11.0	27210128
ECLASS 10.0.1	27210128
ECLASS 9.0	27210128
ECLASS 8.0	27210190
ECLASS 5.1	27210121
ETIM 9.0	EC002918
ETIM 8.0	EC002918
ETIM 7.0	EC002918
ETIM 6.0	EC002918
ETIM 5.0	EC002475
UNSPSC 12.1	39121007

Details: KFD2-UFC-1.D

Informative Literature: KFD2-UFC-1.D

Literature	言語	ファイルタイプ	ファイルサイズ
Application Report - Biological Cleaning of Wastwater and Secondary Sedimentation Stage	ENG	PDF	566 KB
Application Report - Generating Electricity in Coal-Fired Power Plants	ENG	PDF	412 KB
Application Report - Sand Trap and Preliminary Sedimentation Stage	ENG	PDF	448 KB
Application Report - Screening Systems in Sewage Treatment Plants	ENG	PDF	577 KB

Product Documentation: KFD2-UFC-1.D

Brief Instructions	言語	ファイルタイプ	ファイルサイズ
Operator card KF-UFC-1.D / Bedienkarte KF-UFC-1.D	ALL	PDF	849 KB
Safety and Security Documentation
Instruction manual	ENG	PDF	47 KB
Functional Safety Manual	ENG	PDF	2055 KB
Manuals
Manual	ENG	PDF	1757 KB
System Manual	ENG	PDF	3694 KB
Installation and configuration guide Device Type Manager (DTM)	ENG	PDF	8665 KB

Design / Simulation: KFD2-UFC-1.D

CAD	言語	ファイルタイプ	ファイルサイズ
CAD 3-D / CAD 3-D	ALL	STP	870 KB
CAD Portal / CAD Portal	ALL	LINK	---
CAE
CAE EPLAN Data Portal / CAE EPLAN Data Portal	ALL	LINK	---
CAE EPLAN macro EDZ / CAE EPLAN Makro EDZ	ALL	EDZ	588 KB

Approvals: KFD2-UFC-1.D

Certificates	認証番号	言語	ファイルタイプ	ファイルサイズ
DNV Marine	TAA00001WX	ALL	PDF	106 KB
Europe Pepperl+Fuchs ATEX Category 3 G	PF 08 CERT 1216 X	ALL	PDF	214 KB
USA Canada UL cULus Hazardous Location UL E223772 UL	CoC 20200622 - E223772 RepRef 20071210	ALL	PDF	82 KB
exida Functional Safety Assessment	P+F 04/03-15 R016	ALL	PDF	337 KB
Declaration of Conformity
EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F)	DOC-0032C	ALL	PDF	51 KB
UKCA-Declaration of conformity / UKCA-Konformitätserklärung	DOC-5301	ALL	PDF	67 KB

Software: KFD2-UFC-1.D

Device Description Files/Drivers	Release Info	ファイルタイプ	ファイルサイズ
DTM Collection Interface Technology 2 / DTM Collection Interface Technology 2	1.4.110.77	ZIP	---
Software Tools
PACTware 4.1 SP6 / PACTware 4.1 SP6	4.1.0.53	ZIP	43327 KB
PACTware 5.0 / PACTware 5.0	5.0.5.31	ZIP	44203 KB
PACTware 6.X / PACTware 6.X	6.1	ZIP	335938 KB

関連製品: KFD2-UFC-1.D

Matching System Components

	DTM Interface Technology DTM collection
	Device DTM, For K-, E- and H-System, Frame application, like e. g. PACTware, must be installed separatelypa

	PACTware 5.0 FDT Framework
	Universal DTM host platform, For all DTMs of Pepperl+Fuchs, Approved FDT/DTM technology, Free of charge, Download from Pepperl+Fuchs websitepa

	K-ADP-USB Adapter with USB Interface
	Isolated USB interface cable, Used with K-, E- and H-System devices, Used with PACTwarepa

	KFD2-EB2 Power Feed Module
	Interface for Power Rail, Supply current ≤ 4 A, Replaceable fuse, Relay contact output, reversible, LED status indicationpa

	UPR-03 Universal Power Rail
	35 mm DIN mounting rail with 3-conductor insert, Provides DC supply voltage to all equipped K-System modules, Standard length 2 m (6 foot), simple to customize to application space, Eliminates daisy-chainspa

	UPR-03-M Universal Power Rail
	35 mm DIN mounting rail with 3-conductor insert, Provides DC supply voltage to all equipped K-System modules, Standard length 1.6 m (5 foot), simple to customize to application space, Eliminates daisy-chainspa

	UPR-03-S Universal Power Rail
	35 mm DIN mounting rail with 3-conductor insert, Provides DC supply voltage to all equipped K-System modules, Standard length 0.8 m (2.6 ft), simple to customize to application space, Eliminates daisy-chainspa

	K-DUCT-GY Profile Rail
	Cable trunking is integrated in the mounting profile, Safe spacious separation of field and control signals, No additional cable guides necessary, Standard length 1.8 m (5.8 ft), simple to customize to application space, With mounting aidspa

	K-DUCT-GY-UPR-03 Profile Rail
	Cable trunking with integrated Power Rail UPR-03, Safe spacious separation of field and control signals, No additional cable guides necessary, Provides DC supply voltage to all equipped K-System modules, Standard length 1.8 m (5.8 ft), simple to customize to application space, With end caps UPR-E, cover and mounting aidspa

	PACTware 6.x FDT Framework
	Universal DTM host platform, For all DTMs of Pepperl+Fuchs, Approved FDT/DTM technology, Free of charge, Download from Pepperl+Fuchs websitepa

Accessories

	K-250R Measuring resistor
	1-channel, Precision resistor, Conversion of 0 mA ... 20 mA/0 V ... 5 Vpa

	K-500R0%1 Measuring resistor
	1-channel, Precision resistor, Conversion of 4 mA ... 20 mA/2 V ... 10 Vpa

	KF-ST-5GN Terminal Block
	3-pin screw terminal, For KF modules of K-System, Packaging unit: 5 pieces greenpa

	KF-CP Coding Pins
	Coding of K-System terminal blocks, Coding of LB/FB-System front sockets, Packaging unit: 20 x 6 coding pinspa

General Notes Relating to Pepperl+Fuchs Product Information

クイックリンク

Selector for Safety Products

Choose from various selection criteria like safety integrity level, performance level, device function, and signal type and find the SIL/PL assessed device that you are looking for.