HART Transmitter Power Supply, Input Isolator FB3202B2

1-channel
Input Ex ia
Power supply for 2- or 3-wire transmitters with 4 mA ... 20 mA
Module can be exchanged under voltage (hot swap)
Installation in suitable enclosures in Zone 1
Supply circuit 15 V (20 mA)
Input from active signals of 4-wire transmitters
HART communication via field bus or service bus
HART communication also for separately powered devices
Simulation mode for service operations (forcing)
Line fault detection (LFD) and Live Zero monitoring
Permanently self-monitoring

Technical Data
Informative Literature
Product Documentation
Design / Simulation
Approvals
お問い合わせ

注: Pepperl+Fuchs GmbH(旧社名)で発行された証明書・適合宣言書などすべての製品関連文書は、Pepperl+Fuchs AG(新社名)にそのまま適用されます。

データシート(PDF):

技術データ FB3202B2

Slots
Occupied slots		1
Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies FB92**
Power dissipation		0.75 W
Power consumption		1.1 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog input
Number of channels		1
Suitable field devices
	Field device	pressure converter
	Field device [2]	flow converter
	Field device [3]	level converter
	Field device [4]	Temperature Converter
Field device interface
	Connection	2-wire transmitter
	Connection [2]	3-wire transmitter
	Connection [3]	4-wire transmitter
Connection		2-wire transmitter (HART): supply circuit: 2/3+, 4/5- 3-wire transmitter (HART): supply circuit: 2/3+, 6- measuring circuit: 4/5+, 6- 4-wire transmitter (separately powered): measuring circuit: 4/5+, 6- HART measuring circuit: 1+, 6-
Transmitter supply voltage		min. 15 V at 20 mA ; 21.5 V at 4 mA
Input resistance		15 Ω (terminals 5, 6) 236 Ω (terminals 1, 6) HART
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: > 22 mA configurable between 0 ... 26 mA
	Open-circuit	factory setting: < 1 mA configurable between 0 ... 26 mA
HART communication		yes
HART secondary variable		yes
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
	Influence of ambient temperature	0.1 %/10 K of the signal range
Resolution		12 Bit (0 ... 26 mA)
Refresh time		100 ms
Indicators/settings
LED indication		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1) red: line fault (lead breakage or short circuit) Status LED (2) yellow: Live Zero monitoring
Coding		optional mechanical coding via front socket
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2013
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Environmental test		EN 60068-2-14:2009
Shock resistance		EN 60068-2-27:2009
Vibration resistance		EN 60068-2-6:2008
Damaging gas		EN 60068-2-42:2003
Relative humidity		EN 60068-2-78:2001
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Relative humidity		95 % non-condensing
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz; transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g; 10 cycles frequency range 5 ... 100 Hz; transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g; 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 (module) , a separate housing is required acc. to the system description
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 350 g
Dimensions		28 x 107 x 132 mm (1.1 x 4.2 x 5.2 inch)
Data for application in connection with hazardous areas
EU-type examination certificate		BVS 13 ATEX E 050 X
	Marking	II 2(1) G Ex d [ia Ga] IIC T4 Gb II (1) D [Ex ia Da] IIIC
Supply
	Voltage	27 V
	Current	92 mA
	Power	619 mW (linear characteristic)
Connection 1-6
	Voltage	8.9 V
	Current	4 mA
	Power	24 mW (trapezoid characteristic curve)
Input
	Voltage	0.7 V
	Current	7 mA
	Power	5 mW (trapezoid characteristic curve)
	Internal capacitance	242 nF
	Internal inductance	0 mH
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11:2007 , voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN IEC 60079-0:2018+AC:2020 EN 60079-1:2014 EN 60079-11:2012
International approvals
ATEX approval		BVS 13 ATEX E 050 X
General information
System information		The module has to be mounted in appropriate backplanes and housings (FB92**) in Zone 1, 2, 21, 22 or outside hazardous areas (gas or dust). Here, observe the corresponding EC-type examination certificate.
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.

Classifications

System	Classcode
ECLASS 13.0	27210120
ECLASS 12.0	27210101
ECLASS 11.0	27210120
ECLASS 10.0.1	27210120
ECLASS 9.0	27210120
ECLASS 8.0	27210120
ECLASS 5.1	27210120
ETIM 9.0	EC001485
ETIM 8.0	EC001485
ETIM 7.0	EC001485
ETIM 6.0	EC001485
ETIM 5.0	EC001485
UNSPSC 12.1	39121008

Details: FB3202B2

Informative Literature: FB3202B2

Literature	言語	ファイルタイプ	ファイルサイズ
Application Report - Communication Redundancy for Uninterrupted Operation	ENG	PDF	529 KB
Application Report - LB and FB Remote I/O Systems for Digitally Connecting Analog Field Devices	ENG	PDF	208 KB
Application Report - Space Saving Extension for Existing Plants	ENG	PDF	300 KB
Application Report - Using Remote I/O Systems for the Efficient Digitalization of Plants	ENG	PDF	371 KB

Product Documentation: FB3202B2

Safety and Security Documentation	言語	ファイルタイプ	ファイルサイズ
Instruction manual	ENG	PDF	65 KB
Manuals
Hardware Manual FB-Remote-I/O-System	ENG	PDF	9157 KB

Design / Simulation: FB3202B2

CAE	言語	ファイルタイプ	ファイルサイズ
CAE EPLAN Data Portal / CAE EPLAN Data Portal	ALL	LINK	---
CAE EPLAN macro EDZ / CAE EPLAN Makro EDZ	ALL	EDZ	104 KB

Approvals: FB3202B2

Certificates	認証番号	言語	ファイルタイプ	ファイルサイズ
Europe DEKRA EXAM ATEX Category (1) D ATEX Category 2 (1)	BVS 13 ATEX E 050 X	ALL	PDF	6278 KB
Lloyd's Register Marine	LR2003616TA-02	ALL	PDF	557 KB
Declaration of Conformity
EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F)	DOC-1047C	ALL	PDF	1041 KB